i want to rebuild engine s65

wheelpro · 10-08-2015, 04:40 AM

Hi All
please i want to rebuild my engine ,
its m3 e92 , with super charger
after some friend drive my car with out methanol , for 2 days
i found oil leak from blow valve
when i saw that , i feel my piston , or something wrong happened in engine
now i am looking for upgrade this engine for max performance ,
please i want advice for good brand with good price too

Weyne Masters · 10-08-2015, 07:39 AM

Wellpro you should go to Www.VAC.com

jdamore · 10-08-2015, 08:34 AM

You have the worst luck with your car. First the supercharger, now the engine! You need to be more careful man!

What about a Dinan Stroker?

lutfy · 10-08-2015, 09:15 AM

Quote:

Originally Posted by Weyne Masters

Wellpro you should go to Www.VAC.com

+1. From Lebanon and they do good amount of business in the Middle East.

Cheers,

Lutfy

wheelpro · 10-08-2015, 09:52 AM

Quote:

Originally Posted by jdamore

You have the worst luck with your car. First the supercharger, now the engine! You need to be more careful man!

What about a Dinan Stroker?

??

wheelpro · 10-08-2015, 09:54 AM

Quote:

Originally Posted by wheelpro

Quote:

Originally Posted by jdamore

You have the worst luck with your car. First the supercharger, now the engine! You need to be more careful man!

What about a Dinan Stroker?

??

Too much
Dinan told. Me it will coast up to 25 k

wheelpro · 10-08-2015, 09:55 AM

Quote:

Originally Posted by lutfy

Quote:

Originally Posted by Weyne Masters

Wellpro you should go to Www.VAC.com

+1. From Lebanon and they do good amount of business in the Middle East.

Cheers,

Lutfy

More details please

Mit_Boost · 10-08-2015, 03:25 PM

Quote:

Originally Posted by wheelpro

Too much
Dinan told. Me it will coast up to 25 k

If 25k is "too much," then you're not ready to rebuild this engine for "max performance." 25k is going to be right around where the build will set, between the aftermarket rods & pistons, standard additional bits (bearings, wrist pins, gaskets, etc.) and then the machining. Plus, it'll probably make sense to upgrade to the ARH Headers if you're pushing this much power, so that's another cost outside the motor build.

VT3M33 and IMG are running the highest HP S65's on the forums (both over 700 WHP), and they both used Prime Performance to build their motors. I'd recommend contacting them.

Malek@MRF · 10-08-2015, 05:25 PM

Shoot me an email. I can help you out.

VF-Engineering · 10-08-2015, 05:55 PM

http://vf-engineering.com/vfe90-race-engine/

Just sayiiinnn....

Good luck with your build. Sorry to hear about that oil leak!

Mit_Boost · 10-08-2015, 07:18 PM

Quote:

Originally Posted by VF-Engineering

http://vf-engineering.com/vfe90-race-engine/

Just sayiiinnn....

Is anyone running this setup? Or are the components just for sale?? Active said they were working on a YSI/Low Compression S65, don't remember seeing anything beyond a short YouTube dyno video.

VF-Engineering · 10-08-2015, 07:27 PM

Quote:

Originally Posted by Mit_Boost

Is anyone running this setup? Or are the components just for sale?? Active said they were working on a YSI/Low Compression S65, don't remember seeing anything beyond a short YouTube dyno video.

We have 6 of these set-ups on the road right now that have been running for just over a year. They're running the stock supercharger kits, so we haven't turned the boost up on them yet, however we plan to.

wheelpro · 10-09-2015, 03:15 AM

I want to rebuild but my budget max 10 k
May be i can buy pistons with low compression !
Like vac co. Said
I know dinan and vf great but price too high

OM VT3 · 10-09-2015, 03:45 PM

Quote:

Originally Posted by wheelpro

I want to rebuild but my budget max 10 k
May be i can buy pistons with low compression !
Like vac co. Said
I know dinan and vf great but price too high

Cant be done for 10 maybe you can go low comp but you will snap the stock rods woth a bit of power so no point

Mit_Boost · 10-09-2015, 07:40 PM

Quote:

Originally Posted by wheelpro

I want to rebuild but my budget max 10 k
May be i can buy pistons with low compression !
Like vac co. Said
I know dinan and vf great but price too high

10k might get a stock rebuild setup + machining OR a replacement motor from a reputable source. I would highly recommend that you don't just buy any replacement S65 motor, just in case you' get sold an unhealthy motor -- History of detonation problems, poor maintenance by previous owner, worn out bearings, etc.

wheelpro · 10-10-2015, 02:48 PM

I want to rebuild but my budget max 10 k
May be i can buy pistons with low compression !
Like vac co. Said
I know dinan and vf great but price too high

wheelpro · 10-22-2015, 07:37 AM

what about ppm they offer me
any idea ?

wheelpro · 10-22-2015, 04:12 PM

please i want any replies for stoker kite for s65 ?

Cidle · 10-22-2015, 04:34 PM

Quote:

Originally Posted by wheelpro

please i want any replies for stoker kite for s65 ?

Not a kit but 4K for a stroker crankshaft seems reasonable;
http://store.langracing.com/bmw-s65-stroker-crankshaft/

wheelpro · 10-22-2015, 04:43 PM

Quote:

Originally Posted by cidle323

Not a kit but 4K for a stroker crankshaft seems reasonable;
http://store.langracing.com/bmw-s65-stroker-crankshaft/

only crank ? i think its not good idea to change crank with out pistons and connect
with rings

Cidle · 10-22-2015, 04:49 PM

Quote:

Originally Posted by wheelpro

only crank ? i think its not good idea to change crank with out pistons and connect
with rings

Plenty of con rods and piston options available, just showed you a descent priced crankshaft as a starting point.

wheelpro · 10-25-2015, 04:41 PM

Quote:

Originally Posted by cidle323

Plenty of con rods and piston options available, just showed you a descent priced crankshaft as a starting point.

thanks

10-08-2015, 04:40 AM	#1
wheelpro Lieutenant 196 Rep 594 Posts Drives: M5,F10,JB4,DP,CP,METH,SSP Join Date: Sep 2012 Location: CAIRO iTrader: (0)	i want to rebuild engine s65 Hi All please i want to rebuild my engine , its m3 e92 , with super charger after some friend drive my car with out methanol , for 2 days i found oil leak from blow valve when i saw that , i feel my piston , or something wrong happened in engine now i am looking for upgrade this engine for max performance , please i want advice for good brand with good price too
	Appreciate 0 Tweet Quote

10-08-2015, 07:39 AM	#2
Weyne Masters Lieutenant 87 Rep 414 Posts Drives: M3 LIME ROCK VT2-625 Join Date: Jul 2013 Location: Brazil iTrader: (0)	Wellpro you should go to Www.VAC.com
	Appreciate 0 Quote

10-08-2015, 08:34 AM	#3
jdamore Captain 451 Rep 864 Posts Drives: 2008 e92 M3 Join Date: May 2013 Location: New Jersey iTrader: (4)	You have the worst luck with your car. First the supercharger, now the engine! You need to be more careful man! What about a Dinan Stroker? __________________ -- 08 JB e92 6MT ///M3 ESS VT2-625 --
	Appreciate 0 Quote

10-08-2015, 05:25 PM	#9
Malek@MRF Brigadier General 789 Rep 3,732 Posts Drives: E92 M3, E46 M3, G82 M4 Join Date: Jan 2008 Location: Irvine, California iTrader: (5)	Shoot me an email. I can help you out. __________________ BMW PERFORMANCE SPECIALISTS. Race Engines. Suspension. F/I. Brakes. Race Preparation. Factory Service. Alignments. OFFICIAL PARTNERS: KW. MOTON. Brembo. AP Racing. BBS Motorsport. iND. HRE. Turner Motorsport. VAC. BMW Motorsport. Facebook \| Instagram \| Yelp! \| Flikr Phone: 949-233-0448 \| E-Mail: info@mrfengineering.com
	Appreciate 1 Quote

10-08-2015, 05:55 PM	#10
VF-Engineering Major 1015 Rep 1,387 Posts Drives: F82 M4 Join Date: Nov 2008 Location: Anaheim, CA iTrader: (0)	http://vf-engineering.com/vfe90-race-engine/ Just sayiiinnn.... Good luck with your build. Sorry to hear about that oil leak!
	Appreciate 0 Quote

10-09-2015, 03:15 AM	#13
wheelpro Lieutenant 196 Rep 594 Posts Drives: M5,F10,JB4,DP,CP,METH,SSP Join Date: Sep 2012 Location: CAIRO iTrader: (0)	I want to rebuild but my budget max 10 k May be i can buy pistons with low compression ! Like vac co. Said I know dinan and vf great but price too high __________________ Mohamed kamal elkasaby
	Appreciate 0 Quote

10-10-2015, 02:48 PM	#16
wheelpro Lieutenant 196 Rep 594 Posts Drives: M5,F10,JB4,DP,CP,METH,SSP Join Date: Sep 2012 Location: CAIRO iTrader: (0)	I want to rebuild but my budget max 10 k May be i can buy pistons with low compression ! Like vac co. Said I know dinan and vf great but price too high __________________ Mohamed kamal elkasaby
	Appreciate 0 Quote

10-22-2015, 07:37 AM	#17
wheelpro Lieutenant 196 Rep 594 Posts Drives: M5,F10,JB4,DP,CP,METH,SSP Join Date: Sep 2012 Location: CAIRO iTrader: (0)	what about ppm they offer me any idea ?
	Appreciate 0 Quote

10-22-2015, 04:12 PM	#18
wheelpro Lieutenant 196 Rep 594 Posts Drives: M5,F10,JB4,DP,CP,METH,SSP Join Date: Sep 2012 Location: CAIRO iTrader: (0)	please i want any replies for stoker kite for s65 ?
	Appreciate 0 Quote