BMW M3 Forum (E90 E92)

BMW Garage BMW Meets Register Search Today's Posts Mark Forums Read


Go Back   M3Post - BMW M3 Forum > E90/E92 M3 Technical Topics > Engine, Transmission, Exhaust, Drivetrain, ECU Software Modifications
 
Post Reply
 
Thread Tools Search this Thread
      02-02-2014, 04:41 PM   #45
tmntmn
///M
United_States
160
Rep
1,867
Posts

Drives: e92 M3/M-DCT
Join Date: Feb 2008
Location: Bay Area

iTrader: (6)

can you check what 273A error code is?


Thanks
__________________
THANKS TO:~<RPM>~ ~<SONICMS>~ ~<MODECARBON>~ ~<McKennaPerformance>~
MODS: MODECARBON V2 GTS FRONT LIP & REAR DIFFUSER, AA GREEN FILTER, RPI SCOOPS, PSW, Verstraβe Extended DCT Shifter, ZCP WHEELS (SEMI-GLOSS), OHLINS R&T, Megan Exhaust, AKRA XPIPE, BMW LED INTERIOR, BLACKOUT W/ORION V4 LED AE, OSRAM CBI
Appreciate 0
      02-02-2014, 11:25 PM   #46
regular guy
Lieutenant Colonel
427
Rep
1,947
Posts

Drives: Sprint car
Join Date: May 2013
Location: California

iTrader: (0)

273a - P2271, 273a - P0136, 273A - P013E, 273A - P2270

273A - P2271

273A - P2271
Information saved inDME
Fault code273A - P2271
Fault textOxygen sensor vibration check behind catalytic converter, bank 1
Fault descriptionO2 Sensor Signal Biased/Stuck Rich (Bank 1 Sensor 2)
Condition for fault identificationTest condition: Trim control suspicion with observation of P component and I component leads to guided LEAN control; if the post-cat oxygen sensor signal fails to respond accordingly, the error is assigned to the post-cat oxygen sensor
Terminal condition: Engine running
Voltage condition: none
Condition for fault memory entryAfter K_LAVK_OBD_ACT_NK_M_CNT (1x) LEAN control events the oxygen sensor remains stuck at RICH
Action in service1. Check exhaust system for leaks
2. If OK, replace post-cat oxygen sensor LSNK B1
Fault effect and breakdown warningMIL on after engine runs 2x / no effects on drivability
Driver informationWarning light: MIL
Service instructionNone



273A - P0136

273A - P0136
Information saved inDME
Fault code273A - P0136
Fault textOxygen sensor vibration check behind catalytic converter, bank 1
Fault descriptionO2 Sensor Circuit (Bank 1 Sensor 2)
Condition for fault identificationTest condition: Oxygen sensor signal too low, lower than threshold 649 mV (K_LANK_OBD_S_VL_US) for 2 (K_LANK_OBD_S_CNT) /K_LANK_OBD_S_AUTOM_CNT requests
Terminal condition: Engine running
Voltage condition: none
Condition for fault memory entryTime K_LANK_OBD_S_SA_T (3s) after SA for K_LANK_OBD_S_CNT (2x) /K_LANK_OBD_S_AUTOM_CNT (3x) tries
Action in service1. Check exhaust system for leaks
2. If OK, replace post-cat oxygen sensor LSNK B1
Fault effect and breakdown warningMIL on after engine runs 2x
Driver informationWarning light: MIL
Service instructionNone



273A - P013E

273A - P013E
Information saved inDME
Fault code273A - P013E
Fault textOxygen sensor vibration check behind catalytic converter, bank 1
Fault descriptionO2 Sensor Delayed Response - Rich to Lean (Bank 1 Sensor 2)
Condition for fault identificationTest condition: * Determine whether oxygen sensor voltage remains above 151 mV (K_LANK_OBD_S_SA_US) * Fault after 2 (K_LANK_OBD_S_CNT)/K_LANK_OBD_S_AUTOM_CNT attempts
Terminal condition: Engine running
Voltage condition: none
Condition for fault memory entryFull-load for K_LANK_OBD_S_VL_T (6s) for K_LANK_OBD_S_CNT (2x) /K_LANK_OBD_S_AUTOM_CNT (3x) attempts
Action in service1. Check exhaust system for leaks
2. If OK, replace post-cat oxygen sensor LSNK B1
Fault effect and breakdown warningMIL on after engine runs 2x
Driver informationWarning light: MIL
Service instructionNone



273A - P2270

273A - P2270
Information saved inDME
Fault code273A - P2270
Fault textOxygen sensor vibration check behind catalytic converter, bank 1
Fault descriptionO2 Sensor Signal Biased/Stuck Lean (Bank 1 Sensor 2)
Condition for fault identificationTest condition: Trim control suspicion with observation of P component and I component laeds to guided RICH control; if the post-cat oxygen sensor signal fails to respond accordingly, the error is assigned to the post-cat oxygen sensor
Terminal condition: Engine running
Voltage condition: none
Condition for fault memory entryAfter K_LAVK_OBD_ACT_NK_F_CNT (1x) RICH control events the oxygen sensor sticks at LEAN
Action in service1. Check exhaust system for leaks
2. If OK, replace post-cat oxygen sensor LSNK B1
Fault effect and breakdown warningMIL on after engine runs 2x / no effects on drivability
Driver informationWarning light: MIL
Service instructionNone

Last edited by regular guy; 02-02-2014 at 11:32 PM..
Appreciate 0
      02-06-2014, 12:23 PM   #47
MDIAU
Lieutenant
MDIAU's Avatar
42
Rep
449
Posts

Drives: 2009 AW e92M
Join Date: Dec 2010
Location: VA

iTrader: (14)

Could you help me with code P2626 Bank1 Sensor1? I'm assuming it's the precat o2 sensor.
Thanks in advance!
__________________
Cayenne "wifey"
M3 "mine"
Previous toys: 997.1 GT3, C63, e92M3, 350Z, ISF, IS350, B5 S4, R1/Ninja 636
Appreciate 0
      02-08-2014, 01:01 PM   #48
regular guy
Lieutenant Colonel
427
Rep
1,947
Posts

Drives: Sprint car
Join Date: May 2013
Location: California

iTrader: (0)

Quote:
Originally Posted by MDIAU View Post
Could you help me with code P2626 Bank1 Sensor1? I'm assuming it's the precat o2 sensor.
Thanks in advance!
Most likely you're looking for 2b26. The display in a lot of code readers make it hard to tell the difference between "b" and "6."

2B26 - P155D, Post-44
Appreciate 0
      02-23-2014, 10:18 AM   #49
regular guy
Lieutenant Colonel
427
Rep
1,947
Posts

Drives: Sprint car
Join Date: May 2013
Location: California

iTrader: (0)

2b16 - P1630, 2b16 - P210a, 2b16 - P0639

2B16 - P1630

2B16 - P1630
Information saved inDME
Fault code2B16 - P1630
Fault textThrottle-valve actuator, governor monitoring, bank 2
Fault descriptionThrottle Valve Circuit (Bank 2)
Condition for fault identificationTest condition: Actuator shifts to Failsafe mode
Terminal condition: TERM87
Voltage condition: none
Condition for fault memory entry10 ms
Action in service1. Clear fault memory, conduct EDR electronic throttle control system test,
2. Check plug and wiring harness at DKG2 and EDR2,
3. Replace DKG2 or EDR Bank 2
Fault effect and breakdown warningCC message
Engine speed limited
Reduced power
MIL after engine runs 2x
Driver informationWarning light: MIL, EML, CC message, backup program
Service instructionNone



2B16 - P210A

2B16 - P210A
Information saved inDME
Fault code2B16 - P210A
Fault textThrottle-valve actuator, governor monitoring, bank 2
Fault descriptionThrottle Actuator 'B' Control Motor Circuit/Open
Condition for fault identificationTest condition: Actuator shifts to Failsafe mode
Terminal condition: TERM87
Voltage condition: none
Condition for fault memory entry10 ms
Action in service1. Clear fault memory, conduct EDR electronic throttle control system test,
2. Check plug and wiring harness at DKG2 and EDR2,
3. Replace DKG2 or EDR Bank 2
Fault effect and breakdown warningCC message
Engine speed limited
Reduced power
MIL after engine runs 2x
Driver informationWarning light: MIL, EML, CC message, backup program
Service instructionNone



2B16 - P0639

2B16 - P0639
Information saved inDME
Fault code2B16 - P0639
Fault textThrottle-valve actuator, governor monitoring, bank 2
Fault descriptionThrottle Actuator Control Range/Performance (Bank 2)
Condition for fault identificationTest condition: Actuator reports system error
Terminal condition: TERM87
Voltage condition: none
Condition for fault memory entry10 ms
Action in service1. Clear fault memory, conduct EDR electronic throttle control system test,
2. Check plug and wiring harness at DKG2 and EDR2,
3. Replace DKG2 or EDR Bank 2
Fault effect and breakdown warningCC message
Engine speed limited
Reduced power
MIL after engine runs 2x
Driver informationWarning light: MIL, EML, CC message, backup program
Service instructionNone



2B16 - P0639

2B16 - P0639
Information saved inDME
Fault code2B16 - P0639
Fault textThrottle-valve actuator, governor monitoring, bank 2
Fault descriptionThrottle Actuator Control Range/Performance (Bank 2)
Condition for fault identificationTest condition: Actuator reports system error
Terminal condition: TERM87
Voltage condition: none
Condition for fault memory entry10 ms
Action in service1. Clear fault memory, conduct EDR electronic throttle control system test,
2. Check plug and wiring harness at DKG2 and EDR2,
3. Replace DKG2 or EDR Bank 2
4. With UMWB engine protection check throttle valve assembly for stiction
Fault effect and breakdown warningCC message
Engine speed limited
Reduced power
MIL after engine runs 2x
Driver informationWarning light: MIL, EML, CC message, backup program
Service instructionNone
Appreciate 0
      02-24-2014, 09:09 PM   #50
regular guy
Lieutenant Colonel
427
Rep
1,947
Posts

Drives: Sprint car
Join Date: May 2013
Location: California

iTrader: (0)

2b0d - P152c, 2b0d - P152d, 2b0d - P152e, 2b0d - P152f

2B0D - P152C

2B0D - P152C
Information saved inDME
Fault code2B0D - P152C
Fault textIdle actuator monitoring, bank 1
Fault descriptionIdle-Speed Control Valve Monitoring Dissimilar Desired Values (Bank 1)
Condition for fault identificationTest condition: Difference too large
Terminal condition: TERM87
Voltage condition: Battery voltage > 6.8V (k_egas_can_ed_ub_min)
Condition for fault memory entry300 ms
Action in service1. Clear fault memory, LLS idle actuator system test
2. Check LLS1 voltage supply
3. Replace LLS1
Fault effect and breakdown warningDSC lamp / CC message / engine speed limited to 5000 rpm / reduced power / engine start may be possible only with use of accelerator pedal
Driver informationWarning light: MIL, EML, CC message, backup program
Service instructionNone



2B0D - P152D

2B0D - P152D
Information saved inDME
Fault code2B0D - P152D
Fault textIdle actuator monitoring, bank 1
Fault descriptionIdle-Speed Control Valve Monitoring Incorrect Actual Value (Bank 1)
Condition for fault identificationTest condition: Error detection received via CAN
Terminal condition: TERM87
Voltage condition: Battery voltage > 6.8V (k_egas_can_ed_ub_min)
Condition for fault memory entry100 ms
Action in service1. Clear fault memory, LLS idle actuator system test
2. Check LLS1 voltage supply
3. Replace LLS1
Fault effect and breakdown warningDSC lamp / CC message / engine speed limited to 5000 rpm / reduced power / engine start may be possible only with use of accelerator pedal
Driver informationWarning light: MIL, EML, CC message, backup program
Service instructionNone



2B0D - P152E

2B0D - P152E
Information saved inDME
Fault code2B0D - P152E
Fault textIdle actuator monitoring, bank 1
Fault descriptionIdle-Speed Control Valve Monitoring Actual Value / Desired Value Correlation (Bank 1)
Condition for fault identificationTest condition: Difference too large
Terminal condition: TERM87
Voltage condition: Battery voltage > 6.8V (k_egas_can_ed_ub_min)
Condition for fault memory entry350 ms
Action in service1. Clear fault memory, LLS idle actuator system test
2. Check LLS1 voltage supply
3. Replace LLS1
Fault effect and breakdown warningDSC lamp / CC message / engine speed limited to 5000 rpm / reduced power / engine start may be possible only with use of accelerator pedal
Driver informationWarning light: MIL, EML, CC message, backup program
Service instructionNone



2B0D - P152F

2B0D - P152F
Information saved inDME
Fault code2B0D - P152F
Fault textIdle actuator monitoring, bank 1
Fault descriptionIdle-Speed Control Valve Monitoring Reset Error (Bank 1)
Condition for fault identificationTest condition: Not identical for too long
Terminal condition: TERM87
Voltage condition: Battery voltage > 6.8V (k_egas_can_ed_ub_min)
Condition for fault memory entry250 ms
Action in service1. Clear fault memory, LLS idle actuator system test
2. Check LLS1 voltage supply
3. Replace LLS1
Fault effect and breakdown warningDSC lamp / CC message / engine speed limited to 5000 rpm / reduced power / engine start may be possible only with use of accelerator pedal
Driver informationWarning light: MIL, EML, CC message, backup program
Service instructionNone
Appreciate 0
      02-26-2014, 09:50 AM   #51
regular guy
Lieutenant Colonel
427
Rep
1,947
Posts

Drives: Sprint car
Join Date: May 2013
Location: California

iTrader: (0)

27af - P1411

27AF - P1411

27AF - P1411
Information saved inDME
Fault code27AF - P1411
Fault textSecondary-air pump
Fault descriptionSecondary Air Pump No Activity Detected
Condition for fault identificationTest condition: sls_obdh_mdf_max_intg_norm (after 20s) < KL_SLS_OBDH_HFM_DIAG_MIN & > K_SLS_OBDH_SLP_DEF or
sls_obdh_mdf_max_intg_norm (after 20 sec.) < KL_SLS_OBDH_HFM_DIAG_MIN & < K_SLS_OBDH_SLP_DEF & exhaust lamda not high
Terminal condition: Engine running
Voltage condition: Battery voltage > 10.8 V (k_sls_obd_ub_min)
Condition for fault memory entry30000 ms
Action in service1. Check wiring to secondary air pump
2. Check plugs and wiring harness on secondary air pump
3. If OK, remove secondary air pump relay, and connect the two terminals (30 and 87) in the socket with ignition on, if secondary air pump still does not start, it is defective, replace secondary air pump.
4. If secondary air pump
Fault effect and breakdown warningMIL is on after 2x engine cold start
Driver informationWarning light: MIL
Service instructionNone
Appreciate 0
      02-26-2014, 05:45 PM   #52
Bx Tpr
Captain
Bx Tpr's Avatar
123
Rep
891
Posts

Drives: 23 CSL
Join Date: Feb 2009
Location: NY

iTrader: (8)

Fault code 5A43? Came up for my DCT once.

Can't find it anywhere.

Last edited by Bx Tpr; 02-26-2014 at 06:08 PM..
Appreciate 0
      02-26-2014, 08:15 PM   #53
regular guy
Lieutenant Colonel
427
Rep
1,947
Posts

Drives: Sprint car
Join Date: May 2013
Location: California

iTrader: (0)

Quote:
Originally Posted by Bx Tpr View Post
Fault code 5A43? Came up for my DCT once.

Can't find it anywhere.
Sorry, I only have ECU fault codes, not tranny fault codes.
Appreciate 0
      02-26-2014, 09:06 PM   #54
Bx Tpr
Captain
Bx Tpr's Avatar
123
Rep
891
Posts

Drives: 23 CSL
Join Date: Feb 2009
Location: NY

iTrader: (8)

Quote:
Originally Posted by regular guy View Post
Sorry, I only have ECU fault codes, not tranny fault codes.
Any idea where I can find tranny fault codes other than the dealership?
Appreciate 0
      02-26-2014, 09:29 PM   #55
BPMSport
BimmerPost Supporting Vendor
BPMSport's Avatar
United_States
3381
Rep
7,539
Posts


Drives: Harrop M3 / F10 M5 / F82 M4
Join Date: Apr 2008
Location: SoCal

iTrader: (9)

Garage List
2000 BMW M5  [0.00]
1990 BMW 735i Turbo  [0.00]
2008 BMW M3  [7.50]
2015 BMW M3  [0.00]
2015 BMW M5  [0.00]
Quote:
Originally Posted by Bx Tpr
Quote:
Originally Posted by regular guy View Post
Sorry, I only have ECU fault codes, not tranny fault codes.
Any idea where I can find tranny fault codes other than the dealership?
We can read them remotely if needed. Other than that, an independent shop with a BMW specific tool should be able to.
__________________

-----| Like us on Facebook | Instagram || Tuning Information | Remote Coding |-----
----Visit us at www.BPMSport.com - Emotion. Driven. | Toll Free: (888) 557-5133----
Appreciate 0
      02-26-2014, 09:36 PM   #56
BPMSport
BimmerPost Supporting Vendor
BPMSport's Avatar
United_States
3381
Rep
7,539
Posts


Drives: Harrop M3 / F10 M5 / F82 M4
Join Date: Apr 2008
Location: SoCal

iTrader: (9)

Garage List
2000 BMW M5  [0.00]
1990 BMW 735i Turbo  [0.00]
2008 BMW M3  [7.50]
2015 BMW M3  [0.00]
2015 BMW M5  [0.00]
Quote:
Originally Posted by Bx Tpr View Post
Fault code 5A43? Came up for my DCT once.

Can't find it anywhere.
5A43: DCT Pressure sensor, clutch 2, total failure

This could mean that the pressure sensor is reporting incorrect values, that the pressure sensor circuit has shorted or that the circuit is open.

First thing to do is to read the sensor data from pressure sensor on clutch 2. It's supposed to be within .2 and 1.8 bar pressure.

If the pressure sensor is reporting incorrectly, it needs to be replaced.

Otherwise there is a hardware issue or fluid issue.

This fault will cause clutch circuit 2 to be turned off, which will prevent selection of gears 2, 4 and 6.

Hope this helps.
__________________

-----| Like us on Facebook | Instagram || Tuning Information | Remote Coding |-----
----Visit us at www.BPMSport.com - Emotion. Driven. | Toll Free: (888) 557-5133----
Appreciate 0
      02-26-2014, 09:51 PM   #57
Bx Tpr
Captain
Bx Tpr's Avatar
123
Rep
891
Posts

Drives: 23 CSL
Join Date: Feb 2009
Location: NY

iTrader: (8)

Quote:
Originally Posted by Mike Benvo View Post
5A43: DCT Pressure sensor, clutch 2, total failure

This could mean that the pressure sensor is reporting incorrect values, that the pressure sensor circuit has shorted or that the circuit is open.

First thing to do is to read the sensor data from pressure sensor on clutch 2. It's supposed to be within .2 and 1.8 bar pressure.

If the pressure sensor is reporting incorrectly, it needs to be replaced.

Otherwise there is a hardware issue or fluid issue.

This fault will cause clutch circuit 2 to be turned off, which will prevent selection of gears 2, 4 and 6.

Hope this helps.
It absolutely did! Sending you another PM regarding this.
Appreciate 0
      02-27-2014, 12:32 AM   #58
Brian_Fantana
Second Lieutenant
Brian_Fantana's Avatar
United_States
83
Rep
225
Posts

Drives: 09 Alpine white E90 M3 DCT
Join Date: May 2013
Location: Gig harbor wa

iTrader: (0)

Garage List
2009 M3  [0.00]
How about 27c3? I thought it was the gas cap but just bought one and it came back. Then read it was the dtml pump but read another guy had this code and replaced his pump but it didn't fix it. His last resort was a leak somewhere in his exhaust and he needed a smoke machine.
__________________
They've done studies, you know. Sixty percent of the time, it works every time. ~ Brian Fantana
Appreciate 0
      02-27-2014, 12:58 AM   #59
regular guy
Lieutenant Colonel
427
Rep
1,947
Posts

Drives: Sprint car
Join Date: May 2013
Location: California

iTrader: (0)

27c3 - P0456

27C3 - P0456

27C3 - P0456
Information saved inDME
Fault code27C3 - P0456
Fault textDMTL leakage detection
Fault descriptionEvaporative Emission System Leak Detected (very small leak)
Condition for fault identificationTest condition: Current rise during diagnosis less than (dmtl_i_ref - dmtl_i_min) x KL_DMTL_I_REF_KORR + dmtl_i_min
Terminal condition: TERM15 off
Voltage condition: 11V < UBatt < 14.5V (k_dmtl_ub_min ; k_dmtl_ub_max), with start using tester: None
Condition for fault memory entrynone
Action in service1. Check filler cap seal
2. Pressurize tank and search for leaks
Fault effect and breakdown warningCC message / possible gasoline odor
Driver informationWarning light: MIL, EML, default program
Service instructionNone
Appreciate 0
      03-02-2014, 02:42 PM   #60
regular guy
Lieutenant Colonel
427
Rep
1,947
Posts

Drives: Sprint car
Join Date: May 2013
Location: California

iTrader: (0)

2739 - P2433, 2739 - P2432, 2739 - P2430

2739 - P2433

2739 - P2433
Information saved inDME
Fault code2739 - P2433
Fault textAir-mass sensor, secondary air, electrical diagnosis
Fault descriptionSecondary Air Injection System Air Flow/Pressure Sensor Circuit High (Bank 1)
Condition for fault identificationTest condition: Air mass > 70 kg/h (K_SL_ML_HFM_DIAG_MAX)
Terminal condition: Engine running
Voltage condition: None
Condition for fault memory entry5 ms
Action in service1. Check plug and wiring harness on Mini-HFM
2. Replace Mini-HFM
Fault effect and breakdown warningMIL on after engine runs 2x
Driver informationWarning light: MIL
Service instructionNone



2739 - P2432

2739 - P2432
Information saved inDME
Fault code2739 - P2432
Fault textAir-mass sensor, secondary air, electrical diagnosis
Fault descriptionSecondary Air Injection System Air Flow/Pressure Sensor Circuit Low (Bank 1)
Condition for fault identificationTest condition: Air mass < -10kg/h (K_SL_ML_HFM_DIAG_MIN)
Terminal condition: Engine running
Voltage condition: None
Condition for fault memory entry5 ms
Action in service1. Check plug and wiring harness on Mini-HFM
2. Replace Mini-HFM
Fault effect and breakdown warningMIL on after engine runs 2x
Driver informationWarning light: MIL
Service instructionNone



2739 - P2430

2739 - P2430
Information saved inDME
Fault code2739 - P2430
Fault textAir-mass sensor, secondary air, electrical diagnosis
Fault descriptionSecondary Air Injection System Air Flow/Pressure Sensor Circuit (Bank 1)
Condition for fault identificationTest condition: Air mass > 0.5 kg/h (K_SL_ML_HFM_OFFSET_MIN)
Terminal condition: Engine off
Voltage condition: None
Condition for fault memory entry5 ms
Action in service1. Check plug and wiring harness on Mini-HFM
2. Replace Mini-HFM
Fault effect and breakdown warningMIL on after engine runs 2x
Driver informationWarning light: MIL
Service instructionNone
Appreciate 0
      03-02-2014, 02:49 PM   #61
regular guy
Lieutenant Colonel
427
Rep
1,947
Posts

Drives: Sprint car
Join Date: May 2013
Location: California

iTrader: (0)

2743 - P0155

2743 - P0155

2743 - P0155
Information saved inDME
Fault code2743 - P0155
Fault textOxygen sensor heater resistance diagnosis before cat. converter, bank 2
Fault descriptionO2 Sensor Heater Circuit (Bank 2 Sensor 1)
Condition for fault identificationTest condition: The upper or lower threshold of the resistance values has been violated, above/below 6.0 ohms (K_LSHVK_DIAG_RU) 14.5 ohms (K_LSHVK_DIAG_RO)
Terminal condition: Engine running
Voltage condition: Battery voltage > 9V (k_ed_ubmin)
Condition for fault memory entrymin. K_LSHVK_DIAG_ANZ_MESS (100) valid calculations of heater resistance - roughly.1.5 sec.
Action in service1. DME software release must be more recent than 07-06-510, fix incorporated since 07-09-521
2. Check plug, wiring harness on pre-cat oxygen sensor LSVK B2,
3. If OK, replace oxygen sensor
Fault effect and breakdown warningMIL lamp on after engine runs 2x /Small influence on drivability
Driver informationWarning light: MIL
Service instructionNone
Appreciate 0
      03-02-2014, 02:50 PM   #62
Amirsm3
Brigadier General
Amirsm3's Avatar
513
Rep
3,482
Posts

Drives: 2011 Space Grey e90 M3
Join Date: Feb 2014
Location: Williams/Flagstaff, AZ

iTrader: (3)

Wow, thanks for the detailed descriptions! Definitely gonna keep this handy in case something happens and I pop a CEL.
__________________
2011 e90 M3 Space Grey DCT ZCP- eAs, BMW Performance, Agency Power, Macht Schnell, iND, Milltek, Volk, Challenge, Stoptech, Ohlins

BMWCCA:518970
Appreciate 0
      03-09-2014, 08:53 PM   #63
tmntmn
///M
United_States
160
Rep
1,867
Posts

Drives: e92 M3/M-DCT
Join Date: Feb 2008
Location: Bay Area

iTrader: (6)

Do you know what codes 2789 and 278a are

Thanks
__________________
THANKS TO:~<RPM>~ ~<SONICMS>~ ~<MODECARBON>~ ~<McKennaPerformance>~
MODS: MODECARBON V2 GTS FRONT LIP & REAR DIFFUSER, AA GREEN FILTER, RPI SCOOPS, PSW, Verstraβe Extended DCT Shifter, ZCP WHEELS (SEMI-GLOSS), OHLINS R&T, Megan Exhaust, AKRA XPIPE, BMW LED INTERIOR, BLACKOUT W/ORION V4 LED AE, OSRAM CBI

Last edited by tmntmn; 03-10-2014 at 02:51 PM..
Appreciate 0
      03-12-2014, 11:18 PM   #64
regular guy
Lieutenant Colonel
427
Rep
1,947
Posts

Drives: Sprint car
Join Date: May 2013
Location: California

iTrader: (0)

273e - P0030

273E - P0030

273E - P0030
Information saved inDME
Fault code273E - P0030
Fault textOxygen sensor final stage diagnosis heater before cat. converter, bank 1
Fault descriptionHO2S Heater Control Circuit (Bank 1 Sensor 1)
Condition for fault identificationTest condition: Driver info includes OPENLOAD
Terminal condition: none
Voltage condition: none
Condition for fault memory entry5000 ms
Action in service1. Check plug and wiring harness on pre-cat oxygen sensor LSVK B1,
2. If OK replace oxygen sensor
Fault effect and breakdown warningMIL on after engine runs 2x
Driver informationWarning light: MIL
Service instructionNone
Appreciate 0
      03-12-2014, 11:37 PM   #65
regular guy
Lieutenant Colonel
427
Rep
1,947
Posts

Drives: Sprint car
Join Date: May 2013
Location: California

iTrader: (0)

273f - P0050

273F - P0050

273F - P0050
Information saved inDME
Fault code273F - P0050
Fault textOxygen sensor final stage diagnosis heater before cat. converter, bank 2
Fault descriptionHO2S Heater Control Circuit (Bank 2 Sensor 1)
Condition for fault identificationTest condition: Driver info includes OPENLOAD
Terminal condition: none
Voltage condition: none
Condition for fault memory entry5000 ms
Action in service1. Check plug and wiring harness on pre-cat oxygen sensor LSVK B2,
2. If OK replace oxygen sensor
Fault effect and breakdown warningMIL on after engine runs 2x
Driver informationWarning light: MIL
Service instructionNone
Appreciate 0
      03-12-2014, 11:41 PM   #66
regular guy
Lieutenant Colonel
427
Rep
1,947
Posts

Drives: Sprint car
Join Date: May 2013
Location: California

iTrader: (0)

2724 - P0132

2724 - P0132

2724 - P0132
Information saved inDME
Fault code2724 - P0132
Fault textOxygen sensor, signal before cat., bank 1
Fault descriptionO2 Sensor Circuit High Voltage (Bank 1 Sensor 1)
Condition for fault identificationTest condition: lavk_atic42_pin_diag_b1 BIT1 or BIT3 or BIT5 or BIT7 set
Terminal condition: none
Voltage condition: none
Condition for fault memory entry3000 ms
Action in service1. Check plug and wiring harness on pre-cat oxygen sensor LSVK B1,
2. If OK replace oxygen sensor
Fault effect and breakdown warningMIL on after engine runs 2x
Driver informationWarning light: MIL
Service instructionNone
Appreciate 0
Post Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 02:49 PM.




m3post
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST