Sponsored by The Tire Rack

[MrMikeHenry]

19x9.5 / 19x11 255/35 295/30

[Gman_e92m3]

Originally Posted by Jaydm

I have the same wheels. What spacers are you using ?

I tried ECS 5mm spacers, but they don't quite sit properly on the BBS

i believe turner motorsports...

[yidgyi]

Apex Arc-8 18x10 squared ET25
Toyo r888r 275/35/18
-3 Camber front, -2.7 camber rear.
5mm spacer front. Ordered a 5mm for rear.
I was about an inch lower in the front but I rub too hard with these tires that low.

[last1left]

Originally Posted by yidgyi

Apex Arc-8 18x10 squared ET25
Toyo r888r 275/35/18
-3 Camber front, -2.7 camber rear.
5mm spacer front. Ordered a 5mm for rear.
I was about an inch lower in the front but I rub too hard with these tires that low.

Proper fitment nice M too

[6ixSpd]

Does anyone have photos of a 20x11 with a 285/30/20?

[jeff@autocouture]

Originally Posted by 6ixSpd

Does anyone have photos of a 20x11 with a 285/30/20?

I just test fit my work Equip 19x11.5 with 285/30/19 i know its not what your looking for but no rub and not an aggressive stretch.

[6ixSpd]

Originally Posted by jeff@autocouture

I just test fit my work Equip 19x11.5 with 285/30/19 i know its not what your looking for but no rub and not an aggressive stretch.

Do you have a photo? What tire brand/model did you use?

I'm trying to avoid a stretched look, most 285/30/20 on a 11" seems.okay if you stick with Michelin.

[jeff@autocouture]

Originally Posted by 6ixSpd

Do you have a photo? What tire brand/model did you use?

I'm trying to avoid a stretched look, most 285/30/20 on a 11" seems.okay if you stick with Michelin.

I dont have a down the car shot that would work for you. i only have a profile shot i snapped for IG. However, I did Michelin PSS. Have room for a 5mm spacer in the rear to really dial it in if i wanted. Or i could have gone up to a 295/30. wheel faces are out getting repainted.

[6ixSpd]

The big issue with 295/30 is how much taller it is than stock. A 285/30 is barely within 3%, if only 295/25 was available in Conti ECS or PSS/PS4S...

[thetastelingers]

Originally Posted by 6ixSpd

Does anyone have photos of a 20x11 with a 285/30/20?

Here's 20x10.5 with 285-30 if that helps

I'll try to find a better rear picture.

20180124_193241 by thetastelingers, on Flickr

[thetastelingers]

Found a couple.

20180204_203716 by thetastelingers, on Flickr

20180204_203706 by thetastelingers, on Flickr

[6ixSpd]

Originally Posted by thetastelingers

Found a couple.

Thanks! That sure does. Do you know what model tire that is?

Car looks great btw!

[thetastelingers]

Originally Posted by 6ixSpd

Thanks! That sure does. Do you know what model tire that is?

Car looks great btw!

Hankook Ventus V12


Thanks!

[_.loso._]

I just bought a set of GMR Wheels.

Specs Front: 18x9.5 +21 (3.5" lip), Rear: 18x10.5 +21 (4" lip)

I test fitted one of the tears and it sticks out any recommendations on any rear camber kits and tire sizes I'm not trying to get an extremely low profile tire.. but I don't know if I have no choose but to do so.

[slowm3]

Originally Posted by _.loso._

I just bought a set of GMR Wheels.

Specs Front: 18x9.5 +21 (3.5" lip), Rear: 18x10.5 +21 (4" lip)

I test fitted one of the tears and it sticks out any recommendations on any rear camber kits and tire sizes I'm not trying to get an extremely low profile tire.. but I don't know if I have no choose but to do so.

Maybe -10 camber for the rear to fit. Sticks out wayyyy too much.

[_.loso._]

Originally Posted by slowm3

Maybe -10 camber for the rear to fit. Sticks out wayyyy too much.

Any recommended brand?

[slowm3]

Originally Posted by _.loso._

Any recommended brand?

I personally think those wheels are too wide for that car. So even if you tried maxing out front and rear camber, with camber kits, you will still need to run a pretty big stretch on the tires. If you want to go static you might have to shop around and see who can make you custom camber kits for your setup, because regular camber plates will not be enough for this setup.

[thetastelingers]

I would check to change the barrel and lip to modify the offset before I did anything else.

[Loki Motorsports]

Originally Posted by slowm3

Maybe -10 camber for the rear to fit. Sticks out wayyyy too much.

It MIGHT fit with gangster camber (RiP your tire-wear) and a gnarly fender roll... At first glance though, it DOES look way overboard. However, I dig those wheels! Nice setup dude. Hope you find a way to make those bad boys fit.

[SSII_E90M3]

Currently
245/35/19 (F) 265/35/19 (R)

Will be testing fitting Saturday
265/30/19 (F) 305/30/19 (R)

I hope they don't rub. but ill see how it goes.

Stock suspension.
No Spacers.
EDC
No rubbing. for now....

[o0wkr0o]

Originally Posted by thetastelingers

Here's 20x10.5 with 285-30 if that helps

I'll try to find a better rear picture.

[img]https://farm5.staticflickr.com/4761/...46562397_b.jpg[/img]20180124_193241 by thetastelingers, on Flickr

Hi, so that's with zcp pack or not
sitting in rear will rub right?
Appreciated

[thetastelingers]

Originally Posted by o0wkr0o

Hi, so that's with zcp pack or not
sitting in rear will rub right?
Appreciated

NOT ZCP pack.
Standard springs. It shouldn't rub though. The car these came off of had coil overs and was lower than my car.

I just lowered the car with swift springs. I will have these wheels back on the car after the alignment Friday. I'll post updated picture next week.