|
|
03-30-2020, 08:53 PM | #89 |
Private
8
Rep 62
Posts |
AP Racing Radical CP9660
Volk ZE40 18x9.5 +20 |
Appreciate
1
jritt@essex1029.00 |
04-24-2020, 06:47 PM | #90 |
Private
34
Rep 89
Posts |
Hey guys, I have a set of AP CP8520 w/ 380mm rotors, and my wheels are 18x10+25 Enkei NT03. I'm pretty sure the 380mm doesn't fit so does anyone know if 372mm rotors will fit? Thanks.
|
Appreciate
0
|
04-14-2021, 02:10 PM | #92 |
First Lieutenant
366
Rep 317
Posts |
Necrothreading a little here, dunno if OP is still updating the first post. I found this while researching my BBK recently and thought it might help!
I have a square set of Bimmerworld TA16's in 18x10ET25. It will clear the Stoptech ST60 street kit (380mm). |
Appreciate
0
|
05-15-2021, 07:40 PM | #93 | |
I want to drive a Zamboni
1132
Rep 5,559
Posts
Drives: 13 E93 M3 18 F80 M3 16 K71
Join Date: Mar 2006
Location: Monte Sereno, CA
|
Quote:
Had the 220M wheels F 19X8.5 ET 29 R 19X9.5 ET 23 Will the Brembo 365mm and 345mm kit clear the wheels.Thanks
__________________
18 F80 Imola Red 6MT
16 K71 F800GT Montego Blue 13 E93 M3 Melbourne Red 2000 E46,2006 E90,09 E82,13 E93 328i,14 F30 335i,18 F80 M3 My next vehicle would be a Zamboni |
|
Appreciate
0
|
05-15-2021, 10:22 PM | #94 | |
Major General
2747
Rep 6,734
Posts
Drives: 'E46 M3 Race Car, '23 X7
Join Date: Jan 2009
Location: Wisconsin - Instagram - @slicer_m
|
Quote:
__________________
'23 X7
'04 M3 - Fall Line Motorsports Built Race Car - S65 swap, Dry Sump, Bosch Stand-Alone ECU, Drenth Sequential Trans, MCS 3-Way, Flossmann Wide Body, Brembo Motorsports Brakes, Drexler LSD, BBS E88 Etc. INSTAGRAM - @Slicer_M |
|
Appreciate
0
|
05-16-2021, 01:31 AM | #95 |
I want to drive a Zamboni
1132
Rep 5,559
Posts
Drives: 13 E93 M3 18 F80 M3 16 K71
Join Date: Mar 2006
Location: Monte Sereno, CA
|
Thank you so much
__________________
18 F80 Imola Red 6MT
16 K71 F800GT Montego Blue 13 E93 M3 Melbourne Red 2000 E46,2006 E90,09 E82,13 E93 328i,14 F30 335i,18 F80 M3 My next vehicle would be a Zamboni |
Appreciate
0
|
06-23-2021, 12:51 PM | #96 |
New Member
0
Rep 11
Posts |
Would like to chime in for some answers. I'm going to pull the trigger on 3 piece BBS sport classics (step lip) or 3 piece BBS RS2's Concaved (step lip) and wondering if they would fit brembo gt 6 pot 380mm with or without spacer.
Specs are 19x10.5 and 19x11.5 not sure on ET Thanks for any info that can be provided |
Appreciate
0
|
10-31-2023, 05:18 AM | #97 |
New Member
2
Rep 19
Posts |
I have Volk Racing TE37 SLs in 18x9.5" ET22 and Brembo 380mm calipers. It is very thight clearence.
Caliper even touches sometimes when the wheel flexes.( hard compression situations). I dremeled the caliper where it rubbed before about 1 mm. It seems to not touch anymore. FYI slicer See the scrathes on the wheel. Last edited by ghalacli; 10-31-2023 at 05:25 AM.. |
Appreciate
0
|
04-02-2024, 03:41 PM | #98 |
First Lieutenant
234
Rep 317
Posts |
Has anyone run the new Brembo B-M6 calipers on a BBK? I was hoping to get those with a 355mm rotor but can't find any fitment info or even a pdf cutaway to check clearance on my wheel.
I have 18x9 +30 Apex Arc 8 in the front. |
Appreciate
0
|
Post Reply |
Bookmarks |
|
|