220M square set-up

GOLFFRR · 04-11-2011, 07:46 PM

Quote:

Originally Posted by Malekreza11

No. 19x10 359M rear wheel with 265-35 PS2 tires.

Suspension, H&R lowering springs on a ZCP car.

Malek knows whats up

Dave07997S · 04-11-2011, 10:54 PM

I would like to run a 275/30/19 front with the 359 rear wheel and my current 285/30/19 for the rear.

What you think Malek??

Dave

DCC · 04-11-2011, 11:08 PM

Quote:

Originally Posted by ring007

I have a ZCP coupe and am running a square setup with 220's on the track. My first setup using 265/35 PS2's on the front caused rubbing on the rear part of the driver side wheel well liner at full lock (passenger side was fine). Didn't shred the tire in the two sessions that I used it like that, but did wear the liner. I have been running 275/30 AD08's (25.5" diameter) all around with good luck since then though.

so you ran a 19x9.5 220 wheel up front with 265/35/19 and it rubbed the liner only on one side? is this a bad rub or just a slight rub?

DCC · 04-11-2011, 11:10 PM

Quote:

Originally Posted by Malekreza11

No. 19x10 359M rear wheel with 265-35 PS2 tires.

Suspension, H&R lowering springs on a ZCP car.

Based on your experience, I should be save running a 19x9.5 220M rear wheel with 265/35/19 up front with a stock non-ZCP suspension...yes?
Thanks

Malek@MRF · 04-12-2011, 02:56 AM

[QUOTE=DCC;9346940][quote=Malekreza11;9344821]No. 19x10 359M rear wheel with 265-35 PS2 tires.

Suspension, H

Malek@MRF · 04-12-2011, 02:57 AM

Quote:

Originally Posted by Dave07997S

I would like to run a 275/30/19 front with the 359 rear wheel and my current 285/30/19 for the rear.

What you think Malek??

Dave

This is not a problem at all. The 30 series opens a lot of room.

DCC · 04-12-2011, 07:18 AM

[quote=Malekreza11;9347850][quote=DCC;9346940]

Quote:

Originally Posted by Malekreza11

No. 19x10 359M rear wheel with 265-35 PS2 tires.

Suspension, H

huh?....

ring007 · 04-12-2011, 08:38 AM

Correct. Funny isn't it.

Not sure how to differentiate between a bad vs. slight rub. I can tell you though that it rubbed through the liner in a spot about 1 inch long (top to bottom) and about 1/8" wide side to side.

Quote:

Originally Posted by DCC

so you ran a 19x9.5 220 wheel up front with 265/35/19 and it rubbed the liner only on one side? is this a bad rub or just a slight rub?

ring007 · 04-12-2011, 08:40 AM

Interesting. Maybe a 10" wheel stretches the tire enough to lower the diameter sufficiently to avoid rubbing? Never thought about that as a solution. Guess I could measure the diameter or my 359 street wheels to see if the 10" width makes a difference.

[QUOTE=DCC;9348458][quote=Malekreza11;9347850]

Quote:

Originally Posted by DCC

huh?....

DCC · 04-13-2011, 01:53 PM

Quote:

Originally Posted by ring007

Correct. Funny isn't it.

Not sure how to differentiate between a bad vs. slight rub. I can tell you though that it rubbed through the liner in a spot about 1 inch long (top to bottom) and about 1/8" wide side to side.

On which part of the liner?
Thanks

Tptboy · 12-30-2011, 01:36 AM

Am I to understand that a square set of rear 220 wheels with 275-30-19 ad08's all around fits a stock car without problems? I am about to pull the trigger on this.

jphughan · 06-26-2012, 12:19 PM

Bump on this thread since it doesn't have a definitive answer to the OP's original question (nor can I find an answer in any other thread), and I'm contemplating this to get around some understeer that's now in my way as I've increased my skills on the track -- but I would be running this setup full-time since I don't yet want to deal with dedicated track wheels and tires. Will OEM rear 220Ms with OEM rear tires fit on the front of a non-ZCP M3 with no modifications? If so, will they protrude outside the fender, and if so by how much? And will they rub at all, and if so how much wheel lock will it take, and does it just tear up the fender liner or will it damage the tire as well?

Boosted-M · 07-02-2012, 02:16 PM

Square setup looks and drives great!

FVM3 · 05-19-2013, 03:18 PM

slammed

GORDON.M3 · 08-27-2017, 01:18 AM

Bump can anyone confirm if you can run 265/35 on the 220M for the fronts?

becausephilchow · 08-27-2017, 04:05 PM

Quote:

Originally Posted by gordon@

Bump can anyone confirm if you can run 265/35 on the 220M for the fronts?

265/35/19 is too tall for the fronts. But, if you're stock height, with a non-aggressive front, it should still fit.

GORDON.M3 · 08-27-2017, 07:42 PM

Quote:

Originally Posted by becausephilchow

265/35/19 is too tall for the fronts. But, if you're stock height, with a non-aggressive front, it should still fit.

Yeah I'm stock height.

Ngilbe36 · 12-06-2017, 07:13 AM

Quote:

Originally Posted by gordon@

Yeah I'm stock height.

What's the word gordon@ ? Did you do it? Did it fit? Im between wrapping them in 275/30 or 265/35

GORDON.M3 · 12-06-2017, 11:54 AM

Quote:

Originally Posted by Ngilbe36

What's the word gordon@ ? Did you do it? Did it fit? Im between wrapping them in 275/30 or 265/35

I haven't done it yet, didn't find a clean set of square 220m for the front yet.
Thinking of just getting new wheels all together, maybe a set of HRE or BBS next summer.

Ngilbe36 · 04-04-2018, 09:46 AM

A quick update:
I am now running 19x9.5 220Ms with 275/30 PS4S on all four corners with no rubbing. Ive got about 120 miles on the setup so far and it feels great. Ive got some 10mm spacers on the way for the rear to bring them out to the same width as the front. Will upload pics later on.
Thanks

BIGMIG · 08-24-2018, 09:55 AM

Quote:

Originally Posted by Ngilbe36

A quick update:
I am now running 19x9.5 220Ms with 275/30 PS4S on all four corners with no rubbing. Ive got about 120 miles on the setup so far and it feels great. Ive got some 10mm spacers on the way for the rear to bring them out to the same width as the front. Will upload pics later on.
Thanks

Any pictures from this set up?

Thx

Ngilbe36 · 08-27-2018, 07:39 AM

Quote:

Originally Posted by MiguelY

Quote:

Originally Posted by Ngilbe36

A quick update:
I am now running 19x9.5 220Ms with 275/30 PS4S on all four corners with no rubbing. Ive got about 120 miles on the setup so far and it feels great. Ive got some 10mm spacers on the way for the rear to bring them out to the same width as the front. Will upload pics later on.
Thanks

Any pictures from this set up?

Thx

[IMG]undefined[/IMG]

04-11-2011, 10:54 PM	#24
Dave07997S Brigadier General 720 Rep 3,964 Posts Drives: 2020 Ford Mustang GT Join Date: May 2009 Location: El Segundo, CA iTrader: (1)	I would like to run a 275/30/19 front with the 359 rear wheel and my current 285/30/19 for the rear. What you think Malek?? Dave __________________ 2020 Ford Mustang GT 6MT PP1 444rwhp (Sold)2013 M3 Coupe-MR/BLK ZCP, 2011 M3 Coupe-MR/Blk 2007 Porsche 997C2S Speed Yellow/Blk sport seats 2004 BMW M3 Imola/Blk
	Appreciate 0 Quote

04-12-2011, 02:56 AM	#27
Malek@MRF BimmerPost Supporting Vendor 731 Rep 3,735 Posts Drives: E92 M3, E46 M3, G82 M4 Join Date: Jan 2008 Location: Irvine, California iTrader: (5)	[QUOTE=DCC;9346940][quote=Malekreza11;9344821]No. 19x10 359M rear wheel with 265-35 PS2 tires. Suspension, H __________________ BMW PERFORMANCE SPECIALISTS. Race Engines. Suspension. F/I. Brakes. Race Preparation. Factory Service. Alignments. OFFICIAL PARTNERS: KW. MOTON. Brembo. AP Racing. BBS Motorsport. iND. HRE. Turner Motorsport. VAC. BMW Motorsport. Facebook \| Instagram \| Yelp! \| Flikr Phone: 949-233-0448 \| E-Mail: info@mrfengineering.com
	Appreciate 0 Quote

12-30-2011, 01:36 AM	#33
Tptboy Private 0 Rep 53 Posts Drives: 2021 BMW m340ix, 2020 BMW X1 Join Date: Sep 2011 Location: philadelphia, pa iTrader: (0)	Am I to understand that a square set of rear 220 wheels with 275-30-19 ad08's all around fits a stock car without problems? I am about to pull the trigger on this.
	Appreciate 0 Quote

06-26-2012, 12:19 PM	#34
jphughan Brigadier General 594 Rep 4,488 Posts Drives: '16 Cayman GT4 Join Date: Mar 2011 Location: Austin, TX iTrader: (0)	Bump on this thread since it doesn't have a definitive answer to the OP's original question (nor can I find an answer in any other thread), and I'm contemplating this to get around some understeer that's now in my way as I've increased my skills on the track -- but I would be running this setup full-time since I don't yet want to deal with dedicated track wheels and tires. Will OEM rear 220Ms with OEM rear tires fit on the front of a non-ZCP M3 with no modifications? If so, will they protrude outside the fender, and if so by how much? And will they rub at all, and if so how much wheel lock will it take, and does it just tear up the fender liner or will it damage the tire as well? __________________ '16 Cayman GT4 (delivery pics, comparison to E92 M3 write-up) Gone but not forgotten: '11.75 M3 E92 Le Mans \| Black Nov w/ Alum \| 6MT (owned 5/2011 - 11/2015) Last edited by jphughan; 06-26-2012 at 12:40 PM..
	Appreciate 0 Quote

07-02-2012, 02:16 PM	#35
Boosted-M First Lieutenant 37 Rep 339 Posts Drives: F10 535D XDrive (USA) Join Date: Apr 2011 Location: Northeast PA & NJ iTrader: (2)	Square setup looks and drives great!
	Appreciate 0 Quote

05-19-2013, 03:18 PM	#36
FVM3 Major General 270 Rep 5,751 Posts Drives: e92 m3, f30 328i Join Date: Sep 2010 Location: Los Angeles iTrader: (2)	slammed
	Appreciate 0 Quote

08-27-2017, 01:18 AM	#37
GORDON.M3 Colonel 1419 Rep 2,998 Posts Drives: E92 M3 • F25 X3 M-Sport Join Date: Dec 2013 Location: LAX/YYZ/NRT iTrader: (11)	Bump can anyone confirm if you can run 265/35 on the 220M for the fronts?
	Appreciate 0 Quote

04-04-2018, 09:46 AM	#42
Ngilbe36 Captain 1619 Rep 880 Posts Drives: 2011 E90 M3, 2019 F150 Join Date: Mar 2017 Location: MI iTrader: (0) Garage List 2011 BMW E90 M3 [0.00]	A quick update: I am now running 19x9.5 220Ms with 275/30 PS4S on all four corners with no rubbing. Ive got about 120 miles on the setup so far and it feels great. Ive got some 10mm spacers on the way for the rear to bring them out to the same width as the front. Will upload pics later on. Thanks
	Appreciate 0 Quote