|
|
|
Post Reply |
|
Thread Tools | Search this Thread |
06-16-2022, 06:49 PM | #1 |
Second Lieutenant
274
Rep 298
Posts |
FS: 2009 S65 long block 78k miles, Spun Bearing(still runs)
2009 s65 long block with 78k miles. Spun bearing number 1. Has upgraded BE rod bearings and ARP bolts, Bimmerworld dipstick oil pan mod installed. Was still running when removed. $1000 OBO. Pickup only. Last edited by bmwm3s65; 01-28-2024 at 10:10 AM.. |
06-17-2022, 08:18 AM | #2 |
First Lieutenant
186
Rep 392
Posts |
It spun a bearing with BE bearings?
__________________
|
Appreciate
2
DrFerry6748.00 Robocop30512.00 |
07-04-2022, 03:23 AM | #7 |
New Member
8
Rep 27
Posts |
1
|
Appreciate
2
DrFerry6748.00 Robocop30512.00 |
07-08-2022, 01:32 PM | #8 | |
Second Lieutenant
274
Rep 298
Posts |
Quote:
|
|
Appreciate
3
|
07-12-2022, 03:54 PM | #10 | |
BimmerPost Supporting Vendor
1452
Rep 1,614
Posts |
Quote:
|
|
Appreciate
4
|
07-15-2022, 02:34 PM | #11 | |
Second Lieutenant
274
Rep 298
Posts |
Quote:
|
|
Appreciate
1
DrFerry6748.00 |
07-15-2022, 02:38 PM | #12 |
Second Lieutenant
274
Rep 298
Posts |
Here is a picture of the slight damage to the journal before installing the replacement bearing. It drove just fine to the dealership which was about 4 miles away. I have not torn down the engine again after it was pulled to see if more damage was done.
|
Appreciate
2
DrFerry6748.00 Assimilator1615.50 |
09-21-2022, 06:47 AM | #17 | |
Field Marshal
6748
Rep 1,829
Posts
Drives: '08 E92 M3
Join Date: Jul 2010
Location: Greenville, SC
|
Quote:
__________________
'08 E92 M3 DCT Melbourne Red/Bamboo Beige Leather/EDC/SSP Spec-R DCT clutch discs/SSP Pro-Gold DCT Fluid/Quaife LSD/3:45 Final Drive by Diffs Online/BE Bearings & ARP Bolts/Vibra Technics Engine Mounts/M3 World HFC X-Pipe/LUX H8 180/BPM Sport DCT Tune/PFC Z-Rated Pads/ECS Brass Brake Caliper Bushings/Alex Shop Solid Sub-frame Bushings/Motul 600/Tint
|
|
Appreciate
3
|
01-28-2024, 10:17 AM | #18 |
Second Lieutenant
274
Rep 298
Posts |
I had BE bearings already installed, prior to it spinning. I actually replaced the damaged shell with my original oem shell that I kept after having the BE bearings installed. I pulled the pan and confirmed that the oem shell i put back in before driving to the dealer appeared to have no additional wear. sorry for the really really late replay.
|
Appreciate
2
DrFerry6748.00 Assimilator1615.50 |
01-29-2024, 01:16 PM | #21 |
Second Lieutenant
274
Rep 298
Posts |
|
Appreciate
0
|
01-29-2024, 06:25 PM | #22 |
Second Lieutenant
244
Rep 261
Posts |
Then, I doubt your Main Bearings gave out. If your #1 Main Bearing gave out it would have starved a lot more than just your #1 Rod Bearing. Oil stoppage at #1 would have dried out All the other Bearings in a daisy chain. Your #1 RB may have been too loose and you might have lost the oil film.
When you took out the spun #1 and replaced it with the original one, did the engine “knock” right away? |
Appreciate
2
MilehighM3919.00 Robocop30512.00 |
Post Reply |
Bookmarks |
|
|