|
|
12-20-2021, 03:13 PM | #199 | |
Major
238
Rep 1,318
Posts |
Quote:
So the tolerances will be slightly different for sure. When you get those 5mm spacers you should try one on that side to see how it changes your turning angle. It make end up in a spot it won't rub but will have to test. It's all part of the beauty of modding! Lol |
|
Appreciate
0
|
12-20-2021, 05:53 PM | #200 | |
Lieutenant
176
Rep 527
Posts |
Quote:
I'll try the spacer in the front but even if that resolves the rubbing issue, but if that works, I'll have other problems: 1) front wheels sticking out bit more which I am not sure I'll like the look of it and 2) I'll need to order another pair of 5mm spacers for the back wheels. Hahaha, no stopping in mods parts orders! |
|
Appreciate
0
|
12-20-2021, 05:56 PM | #201 | |
Major
238
Rep 1,318
Posts |
Quote:
So in this car.. Once you drop, the rears will come in and the fronts will come out. That's just where the camber adjustment is for these cars. |
|
Appreciate
0
|
12-20-2021, 06:17 PM | #202 |
Lieutenant
176
Rep 527
Posts |
I should have done some more research on the tire sizing because I just found a thread that confirms how 265/40/18 in the fronts won't work with 18x9.5 spec. There seems to be two options: 1) go with 255/40/18s in the front or 2) downsize the front wheels to 18x9 and keep current front tires. In terms of money saving, 2nd option sounds more sensible but I'd have to sell the two front wheels which may be a headache.
Or, with my car sitting at stock height, and if I avoid full turn to right, maybe this won't cause any issues other than wearing out a bit of layer off the fenderwell. With this set-up purchased for winter season, I can ride this out for the next few months and then swap out to another set with correct tire sizes. However, I'm somewhat concerned that the rubbing will wear down the fenderwell and create an opening that will cause further damage to the reservoir area. |
Appreciate
0
|
12-20-2021, 06:26 PM | #204 | |
Major
238
Rep 1,318
Posts |
Quote:
Also, can you post a link to that thread? I'm curious what the offset consideration is there. Unless it's apex specific which would make sense as their 18x9 offset is likely static. |
|
Appreciate
0
|
12-20-2021, 06:35 PM | #205 | |
Lieutenant
176
Rep 527
Posts |
Quote:
This actually is specific to Apex wheels but here's the link: https://www.m3post.com/forums/showthread.php?t=1590874 |
|
Appreciate
0
|
12-20-2021, 07:08 PM | #206 | |
Major
238
Rep 1,318
Posts |
Quote:
Is it the inner or outer part that is causing the rubbing? |
|
Appreciate
0
|
12-20-2021, 09:00 PM | #207 |
Lieutenant
176
Rep 527
Posts |
It's the outer edge of the front tire rubbing against the spot shown in the pics. Looks like this happens when the wheel is turned in the right direction. I didn't notice this until this AM and the mark on the lining looks very fresh. I think this started to happen as the suspension settled after installing the wheel (suspension lifted and settled over last few days of driving). Also, I noticed very thin layer of plastic built-up from the tire rubbing against it which I was able to peel off with ease. There is still a good deal of plastic integrity when I pushed against the rubbing spot. I hope it will stop at some point and not completely rub off and create an opening.
|
Appreciate
0
|
12-20-2021, 10:17 PM | #208 | |
Colonel
730
Rep 2,770
Posts
Drives: M3
Join Date: Feb 2012
Location: South Florida/ St. Louis
iTrader: (28)
Garage List 2016 BMW X5M [0.00]
08 BMW M3 [0.00] 14 BMW X5 50i - sold [0.00] 09 BMW 335i - Sold [0.00] 09 BMW 328i - Sold [0.00] 07 BMW 328i - Sold [0.00] |
Quote:
I also ran this setup with 275 square on the EC7s 18 inch.. no longer rubbed but seems like you're are just making themselves at home and will probably stop soon... if there is a hole in there makes no difference... won't cause any issues and not a lot of dirt gets in there anyway ...
__________________
Evolve, Eisenmann, Strasse, StopTech, Active Autowerke
|
|
Appreciate
0
|
12-21-2021, 02:40 AM | #210 | |
Lieutenant
176
Rep 527
Posts |
Quote:
|
|
Appreciate
0
|
12-21-2021, 07:09 AM | #211 |
Lieutenant
176
Rep 527
Posts |
Pat: Can't you make emblem like the one in the link?
https://www.m3post.com/forums/showthread.php?t=1881909 |
Appreciate
0
|
12-25-2021, 03:22 AM | #213 | |
Major
238
Rep 1,318
Posts |
Quote:
Car looking slick bro. I particularly like the rear shot revealing the large exhaust tips! 🔥 |
|
Appreciate
0
|
12-25-2021, 03:30 AM | #214 |
Major
238
Rep 1,318
Posts |
If you ever decide to upgrade your taillights to LED, here's an alternative to the OEM LCI. I think I a little over $600 for mine and these are priced lower.
https://bayoptiks.com/products/e92-b...re-lci-and-lci
__________________
|
Appreciate
0
|
12-25-2021, 07:38 AM | #215 |
Private First Class
109
Rep 170
Posts |
Looking great - Rear 3/4 is definitely the best angle.
Wheels are looking pretty flush. I also rub on occasion in the front right when backing at full left lock…have just decided to accept it. Merry Christmas to both of you and your families. Cheers!
__________________
Current Garage: 2008 E93 M3 6MT; 2017 Ford Raptor Supercab; 2019 Jeep JLU Sarah
Previous Toys: 1976 Bronco; 1965 Mustang; 1976 Scout II; 1982 Jeep CJ7; 1999 M3 Vert MT; 1982 911SC Targa Previous Bimmers: 2008 328i coupe x-drive; 2008 128i coupe x-drive; 2014 328i sedan x-drive msport |
Appreciate
0
|
12-25-2021, 01:48 PM | #216 | |
Lieutenant
176
Rep 527
Posts |
Quote:
|
|
Appreciate
0
|
12-25-2021, 01:50 PM | #217 | |
Lieutenant
176
Rep 527
Posts |
Quote:
Thabks for the compliments! I just received 5 mm spacers for the rear which should make the stance in the rear look more flush. |
|
Appreciate
0
|
Post Reply |
Bookmarks |
Thread Tools | Search this Thread |
|
|