(100%) E9x OEM Camera Installation (DIY)

[unrulyteach]

Originally Posted by Dubstar

Tried to change the CAN bus cable on TRSVC? Maybe it's wrong..

I think it's wiring oem wire should be here Wednesday

[SaNGRia]

Originally Posted by unrulyteach

Still getting the same results as i did with f series trsvc module

Did you try without the TRSVC to see are you getting any error on PDC?

I assume you already had rear PDC fitted in. And you are splitting the Canbus from there to the TRSVC. Make sure you are doing a connection while the PDC wires intertwined tightly. Cat5 cables same with canbus cables. If yours intertwined that shouldnt be an issue. Report back!

[unrulyteach]

Originally Posted by SaNGRia

Did you try without the TRSVC to see are you getting any error on PDC?

I assume you already had rear PDC fitted in. And you are splitting the Canbus from there to the TRSVC. Make sure you are doing a connection while the PDC wires intertwined tightly. Cat5 cables same with canbus cables. If yours intertwined that shouldnt be an issue. Report back!

Yea when pdc isn't Sharing wires with trsvc module Pdc works fine with no errors at all, only when sharing wiring, so that's why I'm thinking it's the wiring. Will report back on Wednesday when i install wiring

[SaNGRia]

Originally Posted by unrulyteach

Yea when pdc isn't Sharing wires with trsvc module Pdc works fine with no errors at all, only when sharing wiring, so that's why I'm thinking it's the wiring. Will report back on Wednesday when i install wiring

What is this? Did you made your own socket? If so, is the other end has intertwined cable all the way to the PDC for canbus?

[unrulyteach]

Originally Posted by SaNGRia

What is this? Did you made your own socket? If so, is the other end has intertwined cable all the way to the PDC for canbus?
Attachment 2451339

Yes they do

[SaNGRia]

Originally Posted by unrulyteach

Yes they do

If i was you, i would connect the canbus directly to PDC harness not like additional socket or anything

[unrulyteach]

Originally Posted by SaNGRia

If i was you, i would connect the canbus directly to PDC harness not like additional socket or anything

U mean tapping it?

[SaNGRia]

Originally Posted by unrulyteach

U mean tapping it?

correct. Canbus is a very sensetive data cable you dont want any interruption!

[emanmor345]

Wonder if I can get this in on a K line e90. I have a JBBF81 so my car is wired for kline, havent anything about jumping to jbbf3 there is a KL high version jbbf that seems to be the equivalent to a M version, but its awesome to the the OEM camera, it looks great with the pdc obstacles!

[unrulyteach]

Originally Posted by SaNGRia

correct. Canbus is a very sensetive data cable you dont want any interruption!

That's what i did when i retrofitted ACC i solder it? I'm not quite sure but it's that what u did

[unrulyteach]

Originally Posted by SaNGRia

correct. Canbus is a very sensetive data cable you dont want any interruption!

So i got oem cable but it doesn't hav pins on it or ground connect, hoe did u connect power to jbe and how did u connect canbus again

[unrulyteach]

Had something to do with wiring harness. I tapped each wire just for testing purposes and it worked. Ps cam is in trunk so that's why it's dark. So just need to figure out how to draw power and were to put ground at.

[unrulyteach]

Is it just my module that sounds like a jet engine when it turns on?

[SaNGRia]

Originally Posted by unrulyteach

Is it just my module that sounds like a jet engine when it turns on?

It is overheating somehow. As i thought it is the Canbus cable issue. You re good now. You can connect the negative cable on the chassis somewhere such as the 2 nuts that keeps the Combox bracket in place is one of them and positive to PDC wiring harness. Then you are all set!

[SaNGRia]

Originally Posted by unrulyteach

So i got oem cable but it doesn't hav pins on it or ground connect, hoe did u connect power to jbe and how did u connect canbus again

i used the Pin 10 (KL15) on the fusebox with 5amp fuse and negative to chassis.

[SaNGRia]

Originally Posted by emanmor345

Wonder if I can get this in on a K line e90. I have a JBBF81 so my car is wired for kline, havent anything about jumping to jbbf3 there is a KL high version jbbf that seems to be the equivalent to a M version, but its awesome to the the OEM camera, it looks great with the pdc obstacles!

E90s don't have kline, not even early ones. The pin for Kline is x60002 #2 (on all MSV & MSD DMEs) and you will find on the E9x they all say "not used". (hassmaschine)

What year and model your car is and what is your DME?

But if you re 100% it is Kline then you will need DCAN cuz none of the modules like PDC or TRSVC will communicare over KLine! Too slow

[unrulyteach]

Originally Posted by SaNGRia

It is overheating somehow. As i thought it is the Canbus cable issue. You re good now. You can connect the negative cable on the chassis somewhere such as the 2 nuts that keeps the Combox bracket in place is one of them and positive to PDC wiring harness. Then you are all set!

That's not a good thing any idea why it would be over heating

[emanmor345]

Originally Posted by SaNGRia

E90s don't have kline, not even early ones. The pin for Kline is x60002 #2 (on all MSV & MSD DMEs) and you will find on the E9x they all say "not used". (hassmaschine)

What year and model your car is and what is your DME?

But if you re 100% it is Kline then you will need DCAN cuz none of the modules like PDC or TRSVC will communicare over KLine! Too slow

well yea my car does kline or dcan, but my odb port isnt wired for it

[unrulyteach]

Originally Posted by SaNGRia

E90s don't have kline, not even early ones. The pin for Kline is x60002 #2 (on all MSV & MSD DMEs) and you will find on the E9x they all say "not used". (hassmaschine)

What year and model your car is and what is your DME?

But if you re 100% it is Kline then you will need DCAN cuz none of the modules like PDC or TRSVC will communicare over KLine! Too slow

Did u use pin 10 on the blue or black connector

[unrulyteach]

Does camera auto adjust it self? No matter what i do I'm still swing the silicone

[unrulyteach]

How did u fit handle with cam? Did u install cam afterwards

[SaNGRia]

Originally Posted by unrulyteach

How did u fit handle with cam? Did u install cam afterwards

I wrote the details on the description!!!