(100%) E9x OEM Camera Installation (DIY)

[DimitrisM3]

Originally Posted by SaNGRia

Well i have never seen any of the modules that has a full set of number on the version that works on E series. Usually it includes a letter in it. If that was a working TRSVC on E series then it must be exceptional.

Because I am confused what camera Modul need for e9x with nbt !
From F series from e84-e70 ??

[DimitrisM3]

No answer 🤷🏻*♂️

[dumitru.o]

i had iCam on my e90 with NBT retrofit. i think you can use both iCam and TRSVC from e84 but you will have to wire it before or after the adapter

[DimitrisM3]

Originally Posted by dumitru.o

i had iCam on my e90 with NBT retrofit. i think you can use both iCam and TRSVC from e84 but you will have to wire it before or after the adapter

I have the adapter from Carsystems

[dumitru.o]

i've used that with iCam. not happey with the iCam, i would go for TRSVC. check this topic or the other topics, somebody explained to to wire the TRSVC for the emulator to work

[DimitrisM3]

Originally Posted by dumitru.o

i've used that with iCam. not happey with the iCam, i would go for TRSVC. check this topic or the other topics, somebody explained to to wire the TRSVC for the emulator to work

I read it all but I never found it

[Nickco43]

I have finished fitting the camera to my E92. It really wasn't that terribly difficult to do just that the parts were expensive. I managed to spend $400 on all the parts for this retrofit.

Install notes for anyone else fitting this in the future:

1. E7x top view camera module works just fine.
2. Don't glue the camera in as you will never fit it in the trunk. Make sure you cut enough to where the camera can friction fit in the hole and the lens is sticking pretty far out. Place the camera in the trunk lid, then fit the handle, then push the camera into the handle so that it is snug in place.

[norkus]

Thanks for the great DIY.

I wanted to ask if I have an E92 LCI with front and rear original parktronics, do I still need to buy a PDC module from the E84?

I am going to buy F10 reverse camera, TRSVC and its cable. Would that be enough for me? And what exactly TRVSC do I need? Should be with only one output and that’s enough?

Thanks for your experience and reply.

[dumitru.o]

yes, you need PDC from E84 with reverse camera, also ideal would be TRSVC from the same car (although will work one from e70 also). don t get TRSVC from F series !

[art unique]

I have the full retrofit kit for this DIY if anyone is interested

[norkus]

Originally Posted by art unique

I have the full retrofit kit for this DIY if anyone is interested

how much?

Also, would rear camera from F10 work with TRSVC from E70 but with these outputs? (Top rear view camera) or it requires only with one output?

[dumitru.o]

i ve just told you that trsvc from e70 works, it was said several times on the topic already.....

there is no e70 trsvc with one output

[unrulyteach]

How do i go about adjusting the lines to be after the bumper?

[Mert335d]

Yeah my lines are also a bit „in“ the bumper. Would like to adjust the lines as well. There is a thread about that. I tried by changing the values in NETTODAT.TRC. But it didnt work.

Note: You can only code the TRSVC with K+DCAN (Enhanced) or ICOM.

[Adam M]

Just done this for the second time in a car.

Just wanted to say a huge thanks to Sangria for the hardware and coding support. The man is a legend/genius.

[SaNGRia]

Originally Posted by Adam M

Just done this for the second time in a car.

Just wanted to say a huge thanks to Sangria for the hardware and coding support. The man is a legend/genius.

Appreciated brother

[03BeastCharmer]

I have an old Alekshop rear camera setup that only works occasionally. Wonder if I would switch over easily since I already have a camera wired to the trunk. That was pretty plug n play as the module just piggybacked into the screen and other harnesses, but rarely worked during the summers.

[unrulyteach]

Originally Posted by Mert335d

Yeah my lines are also a bit „in“ the bumper. Would like to adjust the lines as well. There is a thread about that. I tried by changing the values in NETTODAT.TRC. But it didnt work.

Note: You can only code the TRSVC with K+DCAN (Enhanced) or ICOM.

Hmm can u post the thread here

[scroller]

I have changed my PDC because my original PDC module wasn't able to flash to the X1 with the part number i need it so after doing some more research i have done it successfully the retrofit and i'm so happy

[SaNGRia]

Great. Congrats!

[CTMike]

Originally Posted by SaNGRia

Great. Congrats!

Hey SaNGRia… I’m debating an NBT EVO retrofit. Would I still follow the procedure in this thread to retrofit a rear view camera to my 2011 E93 M3? Thanks for all you contribute!

Thanks,
Mike

[SaNGRia]

Originally Posted by CTMike

Hey SaNGRia… I’m debating an NBT EVO retrofit. Would I still follow the procedure in this thread to retrofit a rear view camera to my 2011 E93 M3? Thanks for all you contribute!

Thanks,
Mike

Hey. Yes you can follow the same procedure. And Thank you!