BMW M3 Forum (E90 E92)

BMW Garage BMW Meets Register Search Today's Posts Mark Forums Read


Go Back   M3Post - BMW M3 Forum > E90/E92 M3 Technical Topics > Mechanical Maintenance: Break-in / Oil & Fluids / Servicing
 
EXXEL Distributions
Post Reply
 
Thread Tools Search this Thread
      07-13-2018, 11:02 AM   #1
delirium330
First Lieutenant
delirium330's Avatar
United_States
205
Rep
330
Posts

Drives: 2010 E92 M3 3 Pedals
Join Date: May 2015
Location: West Coast

iTrader: (0)

Valve Cover Leak?

99% sure this is a classic valve cover leak, but figured worth getting a confirmation before I tackle this job. Was getting a burning smell at cold start... and upon inspection saw this.

I think I still have some Loctite RTV 598 from my last BMW valve cover job...
Attached Images
 
Appreciate 0
      07-13-2018, 12:05 PM   #2
Mvy
Captain
United_States
538
Rep
979
Posts

Drives: 2008 E93 M3
Join Date: Nov 2014
Location: GA Peach

iTrader: (0)

Thats it. I just got the same thing starting finally after 10 years. You might want to open the oil cap and check to see how the inside of the cover looks. Mine is all gross and mustardy yellow with chunks falling off. No real worry of engine damage as the oil filter picks it up but its time for new covers with the gasket for me at my next opportunity to remove the super charger.
__________________

Harrop Supercharger, BPM Tune, K/W Coil over kit, Stoptek BBK, Magnaflow exhaust, ear to ear grin everytime I drive...
Appreciate 0
      07-13-2018, 12:32 PM   #3
shimmy23
F15 daddymobile
shimmy23's Avatar
2330
Rep
3,496
Posts

Drives: GS X5
Join Date: Aug 2011
Location: WA

iTrader: (3)

Seems like the mustardy and peeling cover issue is common. Is it recommended to just replace the cover?
Appreciate 0
      07-13-2018, 12:45 PM   #4
Mvy
Captain
United_States
538
Rep
979
Posts

Drives: 2008 E93 M3
Join Date: Nov 2014
Location: GA Peach

iTrader: (0)

Quote:
Originally Posted by shimmy23 View Post
Seems like the mustardy and peeling cover issue is common. Is it recommended to just replace the cover?
Yes. Its expensive but it takes care of the leak and mustard all at once. I think they are 650 each.
__________________

Harrop Supercharger, BPM Tune, K/W Coil over kit, Stoptek BBK, Magnaflow exhaust, ear to ear grin everytime I drive...
Appreciate 0
      07-13-2018, 01:00 PM   #5
shimmy23
F15 daddymobile
shimmy23's Avatar
2330
Rep
3,496
Posts

Drives: GS X5
Join Date: Aug 2011
Location: WA

iTrader: (3)

Quote:
Originally Posted by Mvy View Post
Yes. Its expensive but it takes care of the leak and mustard all at once. I think they are 650 each.
I’ll have to do this eventually. I’ve noticed some leakage. Also read that the early covers can warp?
Appreciate 0
      07-13-2018, 01:26 PM   #6
delirium330
First Lieutenant
delirium330's Avatar
United_States
205
Rep
330
Posts

Drives: 2010 E92 M3 3 Pedals
Join Date: May 2015
Location: West Coast

iTrader: (0)

Yellow mustard build up is interesting. I had a ton of mustard build up on my 2005 330i ZHP, was thick like mayo and I spent 2 hours trying to clean it up before putting the valve cover back on.
Appreciate 0
      07-13-2018, 01:49 PM   #7
pbonsalb
Lieutenant General
5179
Rep
10,557
Posts

Drives: 18 F90 M5, 99 E36 M3 Turbo
Join Date: Feb 2011
Location: New England

iTrader: (4)

I’d probably clean it and see how long it takes to return. Obviously it won’t fix itself but it may not need immediate attention.
Appreciate 0
      07-13-2018, 03:26 PM   #8
Mvy
Captain
United_States
538
Rep
979
Posts

Drives: 2008 E93 M3
Join Date: Nov 2014
Location: GA Peach

iTrader: (0)

Quote:
Originally Posted by pbonsalb View Post
I’d probably clean it and see how long it takes to return. Obviously it won’t fix itself but it may not need immediate attention.
I think its a coating inside that flakes off the magnesium valve cover. I think they put the coating on to protect it but the heat cycles makes it fall off. I am not sure if blasting and re coating it is the best idea, or if just blasting it clean and adding a new gasket would work. I am just leaning towards replacing as the time it will take to clean it up then recoat is going to cost me close to just replacing.
__________________

Harrop Supercharger, BPM Tune, K/W Coil over kit, Stoptek BBK, Magnaflow exhaust, ear to ear grin everytime I drive...
Appreciate 0
      07-13-2018, 04:59 PM   #9
deansbimmer
BimmerPost Supporting Vendor
deansbimmer's Avatar
3741
Rep
2,907
Posts


Drives: 2011 E93 M3
Join Date: Nov 2014
Location: DFW, Texas

iTrader: (17)

Garage List
1988 BMW M3  [0.00]
2013 BMW M3  [0.00]
2011 X5M  [0.00]
2011 BMW M3  [0.00]
The underside isn't fully coated like the exterior. The mfg coats the gasket grooves and any overspray into the underside is all it gets. It doesn't take much time for it to start deteriorating.

Two new covers are over $1200. Most people spend some time cleaning them up and reusing them. Take extra care to clean and smooth the gasket sealing grooves. I use a stainless wheel brush on a rotary tool.
Appreciate 3
UPSROD941.00
Mvy537.50
      07-14-2018, 04:29 PM   #10
motion732
Private First Class
38
Rep
166
Posts

Drives: E92 M3, F30 335 M Sport
Join Date: Jun 2017
Location: Monmouth County, NJ

iTrader: (0)

How bad for the car is it? Mine kinda weeps over a few hundred miles and I just wipe it off
Appreciate 1
      07-14-2018, 07:09 PM   #11
BimmerMan33
Private First Class
BimmerMan33's Avatar
United_States
121
Rep
189
Posts

Drives: 2011 BMW M3, 2014 BMW X5
Join Date: Apr 2014
Location: Illinois, USA

iTrader: (0)

$1200 for a pair of valve covers is too much. I would rather get them sandblasted & powder coated matte red or some other interesting color on the outside, would not coat/color the inside so there would be none to flake off, shouldn't cost over $300 and look cool too!
Appreciate 0
      07-15-2018, 07:04 AM   #12
pbonsalb
Lieutenant General
5179
Rep
10,557
Posts

Drives: 18 F90 M5, 99 E36 M3 Turbo
Join Date: Feb 2011
Location: New England

iTrader: (4)

Quote:
Originally Posted by Mvy View Post
I think its a coating inside that flakes off the magnesium valve cover. I think they put the coating on to protect it but the heat cycles makes it fall off. I am not sure if blasting and re coating it is the best idea, or if just blasting it clean and adding a new gasket would work. I am just leaning towards replacing as the time it will take to clean it up then recoat is going to cost me close to just replacing.
I meant the exterior leak in the picture. BMW has been using magnesium valve covers on some cars since at least the early 90s — M50 and M60 motors—
and the paint or coating on the inside does flake off. The flaking has not killed those motors but maybe the earlier motors were more durable.

Not sure what a flake does when it drops? Disintegrate? Get trapped in the pick up or filter? Score a cam or crank journal?
Appreciate 0
      07-17-2018, 09:43 AM   #13
Mvy
Captain
United_States
538
Rep
979
Posts

Drives: 2008 E93 M3
Join Date: Nov 2014
Location: GA Peach

iTrader: (0)

Quote:
Originally Posted by pbonsalb View Post
Not sure what a flake does when it drops? Disintegrate? Get trapped in the pick up or filter? Score a cam or crank journal?
I think the general consensus is it gets caught in the oil filter without causing damage.
__________________

Harrop Supercharger, BPM Tune, K/W Coil over kit, Stoptek BBK, Magnaflow exhaust, ear to ear grin everytime I drive...
Appreciate 0
      07-19-2018, 08:52 PM   #14
MachinesWithSouls
Colonel
MachinesWithSouls's Avatar
United_States
4833
Rep
2,442
Posts

Drives: 2022 M3 6MT
Join Date: Apr 2015
Location: New Jersey

iTrader: (0)

Garage List
2022 BMW M3  [10.00]
Mine does it marginally, more so if the car is driven harder. I've always just wiped it off and it's been ok.
__________________
2022 M3 6MT - Portimao Blue Metallic
2022 X3 M40i - Tanzanite Blue Metallic
Appreciate 0
      07-20-2018, 07:09 AM   #15
motion732
Private First Class
38
Rep
166
Posts

Drives: E92 M3, F30 335 M Sport
Join Date: Jun 2017
Location: Monmouth County, NJ

iTrader: (0)

Quote:
Originally Posted by SoManyBlueCars View Post
Mine does it marginally, more so if the car is driven harder. I've always just wiped it off and it's been ok.
Exactly what I've been doing and ditto with hard driving. Hoping no issues. Can anyone advise?
Appreciate 0
      07-20-2018, 07:53 AM   #16
deansbimmer
BimmerPost Supporting Vendor
deansbimmer's Avatar
3741
Rep
2,907
Posts


Drives: 2011 E93 M3
Join Date: Nov 2014
Location: DFW, Texas

iTrader: (17)

Garage List
1988 BMW M3  [0.00]
2013 BMW M3  [0.00]
2011 X5M  [0.00]
2011 BMW M3  [0.00]
Crankcase pressures are higher during high rpm/wot conditions as more combustion pressure leaks past the rings than during light operation. It's to be expected that there will be more oil consumption during those conditions, plus leaks if the seals are not 100%.
Appreciate 3
      07-20-2018, 08:54 AM   #17
motion732
Private First Class
38
Rep
166
Posts

Drives: E92 M3, F30 335 M Sport
Join Date: Jun 2017
Location: Monmouth County, NJ

iTrader: (0)

Quote:
Originally Posted by deansbimmer View Post
Crankcase pressures are higher during high rpm/wot conditions as more combustion pressure leaks past the rings than during light operation. It's to be expected that there will be more oil consumption during those conditions, plus leaks if the seals are not 100%.
Thanks for the response.

It seems like one impact would be a slight loss in power (material?). Any other detriments, other than oil in engine bay?
Appreciate 0
      07-20-2018, 09:27 AM   #18
deansbimmer
BimmerPost Supporting Vendor
deansbimmer's Avatar
3741
Rep
2,907
Posts


Drives: 2011 E93 M3
Join Date: Nov 2014
Location: DFW, Texas

iTrader: (17)

Garage List
1988 BMW M3  [0.00]
2013 BMW M3  [0.00]
2011 X5M  [0.00]
2011 BMW M3  [0.00]
Your butt dyno wouldn't be able to notice any difference in power at this level. Oily engine bays deteriorate plastic and rubber parts faster. It seems oily-leaky valve covers also bubble up their coating faster. There may not be an immediately noticeable detriment but it will cost you in the long run.
Appreciate 0
      07-20-2018, 10:38 AM   #19
svinfinity
First Lieutenant
57
Rep
383
Posts

Drives: E92 JEREZ M3
Join Date: Mar 2015
Location: Fort lee nj

iTrader: (0)

I have some seeping through a couple screws but that seems to be the extent of it. I don’t notice any oil loss.
Appreciate 0
      07-20-2018, 10:58 AM   #20
motion732
Private First Class
38
Rep
166
Posts

Drives: E92 M3, F30 335 M Sport
Join Date: Jun 2017
Location: Monmouth County, NJ

iTrader: (0)

Quote:
Originally Posted by deansbimmer View Post
Your butt dyno wouldn't be able to notice any difference in power at this level. Oily engine bays deteriorate plastic and rubber parts faster. It seems oily-leaky valve covers also bubble up their coating faster. There may not be an immediately noticeable detriment but it will cost you in the long run.
Thank you. I clean it off whenever it becomes noticeable as I keep my engine bay as clean as I can. Hopefully no other ill effects.

I wouldn't even call it a leak, more of a slow 'sweat'. Every 3 months or so I'll clean it off.
Appreciate 0
      07-26-2018, 03:13 PM   #21
delirium330
First Lieutenant
delirium330's Avatar
United_States
205
Rep
330
Posts

Drives: 2010 E92 M3 3 Pedals
Join Date: May 2015
Location: West Coast

iTrader: (0)

Just got a quote from a reputable indy shop for this job:

$760 for gaskets.
$900 for gaskets and both oil separators (no additional labor for this, just parts).

I was debating to DIY this... any opinions on length of time/difficulty to DIY? I think I'll plan to do the oil separators either way. I did DIY my E46 ZHP valve cover gasket in the past and have DIY'd my spark plugs on the e92, so that is about as close as I've gotten to the e92 gaskets.

If I DIY, looks like roughly $100 in gasket parts (2 x 11127838271/2) and $200 in oil separator parts (2 x 11157848155), so roughly $300 in parts to DIY. End Result = $600 for shop to do this.

Also, FCP Euro sells a valve cover gasket kit for $176 that includes 8 spark plug tubes... do those need to be replaced as well?

Last edited by delirium330; 07-26-2018 at 03:21 PM..
Appreciate 0
      07-26-2018, 04:48 PM   #22
M3MPH1S
Captain
M3MPH1S's Avatar
United_States
592
Rep
769
Posts

Drives: 2010 E92 M3
Join Date: Mar 2015
Location: Atlanta

iTrader: (8)

Quote:
Originally Posted by delirium330 View Post
Just got a quote from a reputable indy shop for this job:

$760 for gaskets.
$900 for gaskets and both oil separators (no additional labor for this, just parts).

I was debating to DIY this... any opinions on length of time/difficulty to DIY? I think I'll plan to do the oil separators either way. I did DIY my E46 ZHP valve cover gasket in the past and have DIY'd my spark plugs on the e92, so that is about as close as I've gotten to the e92 gaskets.

If I DIY, looks like roughly $100 in gasket parts (2 x 11127838271/2) and $200 in oil separator parts (2 x 11157848155), so roughly $300 in parts to DIY. End Result = $600 for shop to do this.

Also, FCP Euro sells a valve cover gasket kit for $176 that includes 8 spark plug tubes... do those need to be replaced as well?
Definitely do spark plug tubes. I had a spark plug tube leak that prompted me to do the valve cover gasket job, so change them now while you're in there. Depending on how many miles/years are on your car it is a good idea to replace the o-rings around the bolts for the valve covers. The only problem is...for the S65 they decided they wouldn't sell the o-rings by themselves...you have to buy the bolts together. This ended up being the most expensive part of the repair. But since I was at 113k miles it made sense to go ahead and change them.

It's not that difficult of a job to DIY. Getting the plenum off can be a little tricky if you've never done it, and getting the clips off the fuel rail is kind of aggravating (a tiny pick/hook tool was extremely helpful here). I had been under the plenum before, but never done a valve cover gasket job and it only took me about 3 hours.
Appreciate 0
Post Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 05:34 AM.




m3post
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST