|
|
03-08-2018, 09:10 AM | #23 |
Lieutenant
239
Rep 479
Posts |
Also, wipe off the excess gasket sealant too... I did that after I initially placed the oil cap back onto the valve cover. After wiping the excess sealant I placed the cap back on and let it cure for a day. Cheap and simple fix.
|
Appreciate
0
|
03-10-2018, 02:09 AM | #24 |
Private First Class
27
Rep 145
Posts |
I had this issue and took the gasket out to take a close look. The gasket had a slight crack in it which I'm sure caused the leaking.
I flipped the gasket around, cleaned it thoroughly and put it back on. It stopped leaking after that but got a new cap and gasket under warranty anyway. |
Appreciate
0
|
04-30-2019, 10:26 AM | #25 |
Registered
3
Rep 2
Posts |
I had a leak at the filler cap and tried different caps but it still leaked. Dealer recommended I replace the whole valve cover. I noticed once the paints start to wear, there is an uneven lip surface by the filler hole. I lightly sanded the lip to make it smooth and put some high temp touch up paint to seal it. Just make sure you confirm that it is from the filler cap area by cleaning first and seeing where the oil starts from. Leak has been gone and hoping it stays that way.
|
04-30-2019, 11:27 AM | #26 | |
Major General
1889
Rep 5,506
Posts |
Quote:
How did you sand down the surface without dropping stuff into the oil? For touch up paint, aren't those usually sprays? Did you get a brush on one?
__________________
Auto Detailing Enthusiast!
|
|
Appreciate
0
|
06-28-2019, 01:18 PM | #27 | |
Lieutenant
366
Rep 404
Posts |
Quote:
First, I dampened a piece of a shop towel with oil so that dust would have an easier time sticking to it, and put it in the fill hole. Then I got my sweet Metro Vac hand vac, put the flex hose and crevice tool on it, turned it on, held the nozzle on the inner edge of the hole next to where I was sanding, and took it nice and slow. I tried to move the sandpaper and vac nozzle in unison. I figured that between what debris fell outside the engine, what the sandpaper held onto, what the vac picked up, and what fell and stuck onto the shop towel, little if anything would enter the engine. Afterward, I cleaned up first by running the vac nozzle around the rim, and then by wiping the rim down inside-to-outside before gently extracting the shop towel. Then I poured a little oil onto the cam gear and chain to rinse them off for good measure. It looks like I still have a leak, but it's MUCH slower now -- like a weep, almost unnoticeable. FWIW. |
|
Appreciate
0
|
06-28-2019, 01:21 PM | #28 | |
Major
748
Rep 1,256
Posts
Drives: '08 M3, '09 328xi Sport Wagon
Join Date: Oct 2008
Location: Ancaster, ON, Canada
|
Quote:
If you didn't give the gap a thorough cleaning, the oil you're seeing could just be a little residual from underneath the seal on the cap.
__________________
|
|
Appreciate
0
|
06-28-2019, 02:40 PM | #29 |
Lieutenant
366
Rep 404
Posts |
|
Appreciate
0
|
06-28-2019, 07:04 PM | #30 |
Brigadier General
3897
Rep 4,160
Posts |
I had the same oil cap leak when I got my car. Changed the oil cap for the one from the E46 M3 which some forums said was tighter. Leaked reduced significantly but still slowly wept oil over time.
Then I replaced my valve covers due to the paint bubbling. Zero leaks since then, using the same E46 M3 oil cap. |
Appreciate
0
|
06-29-2019, 04:57 PM | #31 |
Stop the hate, get a V8
3850
Rep 8,625
Posts |
As I've mentioned before, a little bit of weeping is normal. Oils that contain esters have some polar action so it will actually climb up the threads and down the side -- you often see this on opened bottles of oil that have been sitting around for a while.
__________________
Now: 2017 Corvette Grand Sport, 2021 AMG C63 S sedan
Past: 2011.5 M3 sedan ZCP |
Appreciate
1
SAMM3Y3085.00 |
06-29-2019, 05:09 PM | #32 | ||
General
63297
Rep 24,651
Posts |
Quote:
Quote:
__________________
"MAX VERSTAPPEN" IS THE 2021+2022+2023 F1 WORLD CHAMPION - #UnLeashTheLion
BPM DEV-Tune & DCT Software-Tune & Servotronic & coding ///Alpine HID Angeleyes ///Oem.exhaust mod. |
||
Appreciate
0
|
06-29-2019, 05:16 PM | #33 |
Colonel
3085
Rep 2,747
Posts |
I have the new style oil cap on newly refinished vc's... it still has a thin oily film around the neck, this makes sense appreciate the info... thanks
__________________
9ers
|
Appreciate
0
|
06-29-2019, 08:11 PM | #34 | |
Lieutenant
366
Rep 404
Posts |
Quote:
Either way, this explanation does make some sense. Wouldn't it also suggest that there should be a difference in leakage rates for different oils? |
|
Appreciate
0
|
06-30-2019, 12:09 PM | #35 |
Major
529
Rep 1,122
Posts |
I've actually ruined some clothes by storing an opened (but TIGHTLY sealed) bottle of ester-based engine cleaner near them. As mentioned by dparm it literally crept up and out of the bottle... Really odd behavior.
|
Appreciate
0
|
07-05-2019, 07:11 AM | #36 |
Registered
0
Rep 2
Posts |
I have bought two oil caps at BMW dealer and still have the leak too. I have 70k miles and now my valve cover are leaking as well too. Are ya'll seeing this issue too?
|
Appreciate
0
|
07-08-2019, 10:37 PM | #37 |
Captain
592
Rep 769
Posts |
My mileage was higher than that, but as described in the OP, my valve covers went around the same time as the oil cap issue cropped up. I posted an update on the OP and someone else in the thread had the same solution - I would 100% recommend using some type of gasket maker to fix the oil cap issue and I would definitely recommend replacing your valve cover gaskets AND spark plug tubes.
|
Appreciate
0
|
Post Reply |
Bookmarks |
Tags |
leak, oil cap, paint, valve cover |
|
|