|
|
02-29-2024, 08:03 AM | #1 |
BimmerPost Supporting Vendor
119
Rep 427
Posts
Drives: All BMW models
Join Date: Feb 2024
Location: Unit 32 Sundon Industrial Estate Dencora Way Luton Bedfordshire LU3 3HP
|
EVOLVE | Eventuri Intakes - Last units available
As an Eventuri dealer we have existing stock ready to ship! These are the last units we have available in stock currently, and with stock generally on back order, we wanted to give customers the chance to order immediately.
2 Units Remaining: Eventuri Gloss Carbon Fibre Intake System for the E9X M3 Performance Gain Dyno: 8-10hp, 10-12ft-lb Performance Gain Road Dyno (Insoric): 16hp, 14Nm IAT Difference with Ambient: Stock 7.5C: Eventuri 4.5C V-Box Acceleration: 100-200kph Reduced By 0.3 Seconds The BMW E90 | E92 | E93 M3 Eventuri intake system is the result of extensive research and optimisation which improves possibly one of the best designed stock intake systems we have seen. The E9X stock airbox system is a brilliantly designed intake with an excellent flow path and feed system for ambient air. However on closer inspection, there are restrictions in the inlet tube connecting the airbox to the inlet manifold. By redesigning the tube yet maintaining the airbox, we have been able to allow the V8 engine to breathe with greater efficiency and therefore gain power. In addition to the new tube design, we also identified a further restriction in the air feed system. To overcome this, we designed a scoop to allow an increase in airflow through the airbox. This reduces inlet temperature values further and adds to the performance gain of the system. Performance Gain Dyno: 8-10hp, 10-12ft-lb Dyno tests were carried out showing a consistent gain of approximately 9hp and 11ft-lb of torque. The gain is not just at the peak but throughout the RPM range. This translates on the road to increased part throttle and full throttle response with the car pulling much more eagerly to the redline. The testing was done on the same day back-to-back and temperatures were monitored to ensure consistency. The car was tested firstly with the stock intake - hood closed. We then left the car on the dyno and installed the Eventuri. The car was then run again - hood closed. Several runs were carried out with both configurations to get a consistent result. Performance Gain Road Dyno (Insoric): 16hp, 14Nm The system was also tested using a road based measurement device (Insoric). On the road, the airflow is a lot better than the fan can achieve on the dyno and so the intake system is able to perform better. Data Logging Flow and Inlet Temperature To monitor and record data output from the ECU we used a Bavarian Technic diagnostics tool. The car was fitted with the stock system and then data was logged in 4th gear to the redline. Then the Eventuri intake was fitted and the same method applied. The outputs show that the air mass flow with the Eventuri is higher across the entire RPM range - with a bigger difference at higher RPM where the restrictions in the stock system become more apparent. Furthermore the difference between the ambient temperature and the inlet air temperature (IAT) is also smaller with the Eventuri due to the scoop enabling a higher air speed through the airbox.
VBox Acceleration Tests We also took the car for some road testing using a Vbox unit to record the acceleration from 60-130mph (also 100-200Km/h). Testing was carried out on the same stretch of road - again on the same day to keep variables minimum. Results show that with just the intake added, the acceleration times from 60-130mph and also 100-200Km/h reduced by approximately 0.3 seconds which is a significant change at such speeds. Acceleration results summary: 60-130mph with Stock intake = 11.157 seconds 60-130mph with Eventuri intake = 10.886 seconds 100-200Km/h with Stock intake = 9.56 seconds 100-200Km/h with Eventuri intake = 9.236 seconds PM me for details |
06-19-2024, 11:17 AM | #5 |
BimmerPost Supporting Vendor
119
Rep 427
Posts
Drives: All BMW models
Join Date: Feb 2024
Location: Unit 32 Sundon Industrial Estate Dencora Way Luton Bedfordshire LU3 3HP
|
Latest Update 19 June!
We have the last remaining units of each of the below Eventuri products, ready to ship today! Eventuri Carbon Fibre Airbox Lid - BMW 3 Series E90 | E92 | E93 M3 The perfect finishing touch to your E90 | E92 | E93 M3 engine bay. Direct replacement for the OEM plastic airbox lid. Made from the same high quality 100% pre-preg carbon fibre that Eventuri use for their intake systems. Gloss: 1 unit in stock. Link Here Matte: 1 unit in stock. Link Here Eventuri Gloss Carbon Fibre Intake System - BMW 3 Series E90 | E92 | E93 M3 Performance Gain Dyno: 8-10hp, 10-12ft-lb Performance Gain Road Dyno (Insoric): 16hp, 14Nm IAT Difference with Ambient: Stock 7.5C : Eventuri 4.5C V-Box Acceleration : 100-200kph Reduced By 0.3 Seconds The BMW E90 | E92 | E93 M3 Eventuri intake system is the result of extensive research and optimisation which improves possibly one of the best designed stock intake systems we have seen. The E9X stock airbox system is a brilliantly designed intake with an excellent flow path and feed system for ambient air. However on closer inspection, there are restrictions in the inlet tube connecting the airbox to the inlet manifold. By redesigning the tube yet maintaining the airbox, we have been able to allow the V8 engine to breathe with greater efficiency and therefore gain power. In addition to the new tube design, we also identified a further restriction in the air feed system. To overcome this, we designed a scoop to allow an increase in airflow through the airbox. This reduces inlet temperature values further and adds to the performance gain of the system. Link Here Eventuri Gloss Carbon Fibre Plenum - BMW 3 Series E90 | E92 | E93 M3 Introducing our E9X M3 Carbon Fiber Plenum. Made from 100% high grade prepreg carbon including the internal trumpets, this plenum replaces the stock plastic version and unleashes the roar of the naturally aspirated BMW V8 engine. 1 unit in stock: Link Here Eventuri Gloss Carbon Fibre Duct Set - BMW 3 Series E90 | E92 | E93 M3 Our E9X M3 carbon ducts are a direct replacement for the OEM plastic ducts to bring that finishing touch to the engine bay. These ducts are made using prepreg carbon and match the rest of our E9X M3 line up for the ultimate OEM+ theme. We have also replaced the flexible joining piece between the ducts and the airbox with an EPDM coupler featuring our raised V logo. 1 unit in stock: Link Here |
Appreciate
0
|
Post Reply |
Bookmarks |
|
|