|
|
|
|
Post Reply |
|
Thread Tools | Search this Thread |
08-11-2010, 05:16 PM | #1 |
RATED M
5
Rep 35
Posts |
FS: OEM CSL Driver and Passenger Seats (Nor Cal Preferred)
Hey folks, it will be sad to see this setup go, as they are the only OEM CSL parts I ever really wanted to install. There's nothing better than being able to experience the pinnacle of piloting your M3 around corners firmly planted in a lightweight OEM CSL alcantara sport seat. Ok, now that you're drooling, here's the details and photos below of what you get. Details This is set of OEM CSL front seats. The drivers seat will come with the seat bucket and the OEM rails which mount easily into the car. Simply 4 bolts and one large German Amphenol connector (no airbag light or complications at all) and you're good to go! Probably the most difficult task is finding a torx socket to swap over the belt receptacle assembly from the stock seat to the OEM CSL bracket. Now the passenger seat was actually acquired separately several months before I even knew I would be able to find a complete drivers side setup. It arrived straight from Germany and included all relevant tilt functional hardware attached to the seat excluding the OEM CSL floor bracket. Now being an optimist I jumped on the opportunity to immediately pick up an OEM CSL bucket for the occasional lap of the 'ring with Forza. Ok i'm kidding, well not really... Moving on, I did quite a bit of research and ended up speaking with the guys at Speedware then Terry over at Griffin Motorwerke in the Berkeley. Terry not only stayed late on a weekday to assist me in assembling the aftermarket recaro hardware but genuinely took an interest in helping me figure out that I could easily use existing off the shelf recaro floor bracket, seat mounts, and sliders to install the seat (links below). This essentially enabled me to mount the passenger seat on the drivers side (recall that this is before I found the complete driver side from m3f member Gavin). http://www.m3forum.net/m3forum/showt...ht=gabbo%20csl Recaro hardware http://www.speedwaremotorsports.com/...mw-e46-bracket http://www.speedwaremotorsports.com/...ument-0-70-9nt http://www.speedwaremotorsports.com/...ed-black-sb001 What I found was that both seat buckets are for all intensive purposes identical, and will easily mount with off the shelf recaro hardware if you dont care about the tilt function. I rarely have more than one passenger so that didnt matter to me. I had this seat installed for about a month or two before buying the complete drivers side setup and installing that. Now since i'm usually the only one in my car 95% of the time I never bothered to pick up passenger side recaro hardware. All you would need is the passenger specific floor mount to bolt this one in on the passenger side. Both the side mounts, slider and floor mount will run you ~$380 new. Depending on your preference I would be willing to sell the seat side mounts, and slider (which are the same regardless of side) unless you would prefer to source an OEM CSL passenger side bracket. If so, its easy enough for me to sell all the aftermarket recaro mounting hardware separately for $350 since they're basically brand new (the same hardware you would need for a pole position). Price No low balling please. I'm just looking to sell for what I paid and share my good fortune with another M3 driver. As you know these are very rare items. I'm looking for $3000 firm, for both seats (complete drivers side setup + passenger bucket only). The seats are also in excellent condition. Or Drivers side for $1700 firm Passenger side for $1350 (without any recaro hardware from speedware), $1500 with non side specific side mounts and slider, or $1600 with everything you need to directly bolt the passenger OEM CSL bucket into the drivers side (Please re-read passenger side write-up above if you have any questions). Prefer to sell them in Nor Cal, but if you are willing to pay for shipping then, I might consider figuring out how to pack these and get them to you. If you are serious or have any questions feel free to call or email me. 415.683.0235 Photos Complete LHD drivers seat Complete LHD drivers seat installed closeup of tilt mechanism components with cover off note OEM CSL part sticker on LHD drivers seat bracket Bolts right into factory mount points Just swap the belt receptacle over with a torx socket Now here's the RHD (aka passenger seat) mounted as LHD drivers seat via the recaro brackets (as detailed above) CSL bucket comparison while at Griffin Motorwerke (note the recaro mounts installed) and another angle comparing both CSL seats demonstrating that the seat angle via the recaro hardware can be configured identical to when the seat is installed with an OEM CSL bracket and finally the e46 CSL bucket vs e90/92 BMW Performance bucket photo some of you may recall I posted last year when I acquired the first seat
__________________
Last edited by eshaun; 08-11-2010 at 05:25 PM.. Reason: photo urls |
09-02-2010, 05:53 PM | #2 |
RATED M
5
Rep 35
Posts |
Update:
Left up for sale is a drivers (left) side OEM CSL Seat Mechanism (Part# 52107895957) including misc tilt hardware from both seats available (refer to #'s 1, 4,9, 10 and misc bolts in the photo from REALOEM below). As both my CSL seat buckets sold by themselves last week, this needs to go as well. Perfect opportunity for someone looking for spare OEM CSL bits or if you already have sourced seats elsewhere. Also if you're a savvy CSL guru you'll notice the top of the brack has been shaved down to allow the bucket to sit a few mm lower to gain headroom, however all mechanisms and tilting of the seat when mounted function 100% as intended. $600 firm for everything noted in the description and photos below (MSRP is ~1500ea just for the bracket from BMW). http://realoem.com/bmw/showparts.do?...27&hg=52&fg=10 Prefer to sell locally, but if you are willing to pay for shipping then I can find out what it would cost. If you are serious or have any questions feel free to call or email me. 415.683.0235
__________________
|
Appreciate
0
|
11-30-2011, 05:38 PM | #3 |
RATED M
5
Rep 35
Posts |
Cyber Weds sale guys: Best offer over $300 gets it
Still have the drivers (left) side OEM CSL Seat Mechanism (Part# 52107895957) including misc tilt hardware from both seats available (refer to #'s 1, 4,9, 10 and misc bolts in the photo from REALOEM in above post). Like to get this out of the garage to someone who can use it. Yes its rare but I have some new artwork that will be replacing its spot on my wall If you are serious or have any questions feel free to call or email me. 415.683.0235
__________________
|
Appreciate
0
|
11-30-2011, 10:47 PM | #4 |
Lieutenant General
360
Rep 16,214
Posts
Drives: 2011 E92 M3
Join Date: May 2006
Location: NORTHERN CALIFORNIA
|
damn i want those BMW performance seats LOL
__________________
stock car
|
Appreciate
0
|
12-09-2011, 05:11 PM | #5 |
Private
4
Rep 89
Posts |
did you switch to the BMW performance seats?
I am strongly considering the BMW performance seats and wanted to know if this mount would work Please email me at smoulton0204 at gmail Thank you |
Appreciate
0
|
Post Reply |
Bookmarks |
|
|