|
|
04-20-2021, 02:46 PM | #1 |
New Member
6
Rep 16
Posts |
EDC delete
Hi!
I'm trying to code out my EDC module. Coilovers have been installed. I've found the following recipe: 1) Unplug EDC module 2) Remove $233 from VO 3) in KOMBI, set EDCK_ALIVE_ZAEHLER and EDCK_ID_MONITOR to "nicht_aktiv" 4) in CAPPL, set EDC to "nicht_aktiv" (later CIC cars set EDC_CIC to "night_aktiv") 5) Clear faults using INPA But this only gets rid of the error message in the kombi and CIC. When scanning the car in INPA there is a error saying the EDC module not present or working. It also does not make any sense to me to remove $233 from VO but not code any modules afterwards. Do anyone know which modules that are affiliated to the EDC module and should be coded after altering the VO ? |
04-20-2021, 03:06 PM | #3 |
New Member
6
Rep 16
Posts |
Thanks for the reply tdott.
The VO is changed and FA_WRITE to both CAS and FRM. So the VO is updated. But then it is necessary to update the correct modules with the new VO. And this is where I am a little stuck - which modules do I now need to run SG_CODIEREN on ? Are the CAS and M3DSC modules related to the EDC and needs to be coded ? Any other modules ? Which modules need to be told that there no longer is any EDC module in the car. |
Appreciate
0
|
04-20-2021, 03:25 PM | #4 | |
Naval Aviator
1073
Rep 749
Posts |
Quote:
__________________
e92 M3 - Interlagos Blue | Recaro GTs w/Fox Red Extended |Carbon Leather
Performance Mods: Alpine Stage II; SuperSprint config: non-resonated down+X-pipes+F1s; cat-less; aFe CAI; Bilstein B16s w/EDC; Brembo BBK; AutoSolutions SSK |
|
Appreciate
0
|
04-20-2021, 10:53 PM | #5 |
New Member
6
Rep 16
Posts |
|
Appreciate
0
|
04-25-2021, 12:09 PM | #6 |
New Member
6
Rep 16
Posts |
Did some further testing to try getting rid of the CDB7 error popping up when scanning the car with INPA.
I have unplugged the blue connector from the EDC module and default coded CIC, KOMBI, CAS and M3DSC with updated VO where $233 is removed. Default coding the CIC changes EDC_CIC to "nicht_aktiv" and default coding KOMBI changes EDCK_ALIVE_ZAEHLER and EDCK_ID_MONITOR to "nicht_aktiv". Default coding cas and M3DSC changes no values. When driving the car everything looks and behaves like normal, but when scanning the car error CDB7 shows up under DDE/DME module in INPA. Do everyone who has coded out EDC have a CDB7 error when scanning car ? Or am I missing something ? |
Appreciate
0
|
08-03-2023, 11:01 AM | #7 | |
Second Lieutenant
51
Rep 226
Posts |
Quote:
Almost all other places where this "EDC coding delete" is discussed, the focus is on removing the white connector. But often it's not specified. In one post, aside from yours, I saw also that they had additionally also removed the blue connector. Did you eventually fix your issues and what was the resolution? And what did you do with the connectors?
__________________
Mods: Alex tune, mod'd X-pipe, MPEv2, MS intake 2, ESS UDP, MFactory CFDSv3, RE SSK, Monoball bearings, SSFBs, TCKR DA susp, PFv3 rotors, AMX seats, Voltphreaks batt.
For sale: Valvetronic X-pipe w/HFCs, BW Race muffler, Test pipes, 19" Vorsteiner VFF103 rims, front thrust arms, stock muffler |
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|