2013 Single Hump DCT M3 for sale.

[aaa335]

Impressive build, how is the ride on the street?

[Lienrocs]

Originally Posted by aaa335

Impressive build, how is the ride on the street?

Thank you.

It's extremely compliant. If I didn't tell you it was all spherical bearings and the spring rates were what they are I'm not sure you'd believe me. I had my mom in the car for a two and a half hour drive and she didn't have a single complaint.

[Lienrocs]

Only price drop before I part it out. 62,500.

[sirdaft1]

Beautiful car and very well done!

[Lienrocs]

Originally Posted by sirdaft1

Beautiful car and very well done!

Thank you.

[Lienrocs]

Last bump before I start pulling the car apart.

[Teddybearcup]

Just curious, how did you like the 2700G's? Any comparisons against other bucket seats with regards to comfort and sizing?

[HOVM3]

id be interested in the carbon DS, the spl goodies, sway bars, Akra gt4 x pipe(have an evo, would be willing to swap the x portion with yours + some cash on top), and the d088 goodies. hope this stuff is available!!!

[Lienrocs]

Originally Posted by Teddybearcup

Just curious, how did you like the 2700G's? Any comparisons against other bucket seats with regards to comfort and sizing?

They're good. Pretty comfortable and fit well. I'm 6 foot, 190 with a 33 inch waist and they're pretty good.

[roastbeef]

what a nicely spec'd car.

[nicksm3]

did this beauty sell?

[Lienrocs]

Originally Posted by nicksm3

did this beauty sell?

It did not. So I kept going.

Added:
Drexler 3.62 diff with driller clutches and shot peened gears
Oe GTS splitter
Oe GTS cage and rsd
M235ir wing
RKP Kevlar trunk
Removed the remaining rubber bushes
FC rear trailing arms
Voltphreaks battery
Sparco qrt-c seats
MCS 3 ways
And other things I can't remember off the top of my head.

[911r]

Originally Posted by Lienrocs

It did not. So I kept going.

Added:
Drexler 3.62 diff with driller clutches and shot peened gears
Oe GTS splitter
Oe GTS cage and rsd
M235ir wing
RKP Kevlar trunk
Removed the remaining rubber bushes
FC rear trailing arms
Voltphreaks battery
Sparco qrt-c seats
MCS 3 ways
And other things I can't remember off the top of my head.

What happened to the Öhlins?

[Fl4tsix]

Originally Posted by Lienrocs

It did not. So I kept going.

Added:
Drexler 3.62 diff with driller clutches and shot peened gears
Oe GTS splitter
Oe GTS cage and rsd
M235ir wing
RKP Kevlar trunk
Removed the remaining rubber bushes
FC rear trailing arms
Voltphreaks battery
Sparco qrt-c seats
MCS 3 ways
And other things I can't remember off the top of my head.

Still for sale?!
New price with all those new mods?

[Lienrocs]

Originally Posted by 911r

What happened to the Öhlins?

They're being rebuilt (at PSI) as we speak and I'm either gonna hang onto them for some garage art, sell them or swap them back in depending how the MCS set up works.

I knew I was forgetting something important:

Also installed new half shafts (both sides), wheel bearings, core4 press in stud hubs (brand new hubs with M14 75mm studs), and Strom uprights. I'm still forgetting something but can't put my finger on it without the car in front of me right now.

Edit: also have the group buy carbon vented hood on the way as well as slons new carbon reinforcement panel to get as much rigidity in the shell as possible.

[Lienrocs]

Originally Posted by Fl4tsix

Still for sale?!
New price with all those new mods?

I'd still sell it. If you're interested PM me and we can discuss a price.

[911r]

Originally Posted by Lienrocs

They're being rebuilt (at PSI) as we speak and I'm either gonna hang onto them for some garage art, sell them or swap them back in depending how the MCS set up works.

I knew I was forgetting something important:

Also installed new half shafts (both sides), wheel bearings, core4 press in stud hubs (brand new hubs with M14 75mm studs), and Strom uprights. I'm still forgetting something but can't put my finger on it without the car in front of me right now.

Edit: also have the group buy carbon vented hood on the way as well as slons new carbon reinforcement panel to get as much rigidity in the shell as possible.

Soon enough you'll parts on display to build another E9x haha. Curious to hear what you have to say about the two!