|
|
05-17-2023, 12:25 AM | #23 |
Private
124
Rep 83
Posts |
Absolutely no risk, it holds the double without any problem and i had put some supports under the motor mounts for security.
This is not necessarily the case for some cheap engine support bars. But it's not a kind of job i like... |
Appreciate
1
chocstraw495.50 |
05-24-2023, 02:36 AM | #24 |
Private
124
Rep 83
Posts |
Custom amplifier support finish :
And alarm installation |
Appreciate
2
DrFerry6728.50 reidetailing600.50 |
05-26-2023, 02:37 AM | #26 |
Private
124
Rep 83
Posts |
An hour ahead of us... and if we made the throttle actuators
Revs were hesitant at cold start, it was not smooth The actuator of left bank one was made in 2021 but the right one was of 2007 origin Customer advices in dealership when there is a problem on a known (wear) part... Then it's good to unmount/remove everything 2 times, a support of the engine harness broken elsewhere and repaired for the occasion I'll give big slaps to the funny ones who work like pigs... Long story short, order at Rebuild on 24/05 at 14h, delivered on 25/05 at 13h30 (that's some serious guys!) Mounted, tested with ISTA, restarted and perfect, smooth and fluid revs and more nervous regime |
Appreciate
2
DrFerry6728.50 reidetailing600.50 |
05-26-2023, 02:40 AM | #27 |
Private
124
Rep 83
Posts |
The beast is Alive!!
After 3 months of work a little night drive to celebrate it Well everything was fine until the moment when the connecting rod n ° 3 decide to throw out the engine block and missed a braking that followed to finish it in an oak 😂.. joking apart from everything is OK , apart from the oil level sensor that takes its time to calculate the level, maybe one day it will get there, it purrs and sounds good, no more lights, messages, noises, it starts to be at my standards to follow we will be able to start the serious things now 😎😈 |
Appreciate
2
DrFerry6728.50 reidetailing600.50 |
06-27-2023, 08:33 AM | #29 |
Field Marshal
6729
Rep 1,829
Posts
Drives: '08 E92 M3
Join Date: Jul 2010
Location: Greenville, SC
|
Tell us about your choice. What final drive ring and pinion gear ratio and type of LSD unit did you decide to go with?
__________________
'08 E92 M3 DCT Melbourne Red/Bamboo Beige Leather/EDC/SSP Spec-R DCT clutch discs/SSP Pro-Gold DCT Fluid/Quaife LSD/3:45 Final Drive by Diffs Online/BE Bearings & ARP Bolts/Vibra Technics Engine Mounts/M3 World HFC X-Pipe/LUX H8 180/BPM Sport DCT Tune/PFC Z-Rated Pads/ECS Brass Brake Caliper Bushings/Alex Shop Solid Sub-frame Bushings/Motul 600/Tint
|
Appreciate
1
///M Power-Belgium63328.00 |
06-28-2023, 04:12 AM | #30 |
Private
124
Rep 83
Posts |
4.1 gears Motorsport shot peened
Drexler GT-Competition 8 disks, plates drilled, 60% /40% lock I ask Driftflo how and where i drive and what i want, he explain and tell me what setup will be good |
Appreciate
2
DrFerry6728.50 reidetailing600.50 |
07-01-2023, 04:23 PM | #32 |
Field Marshal
6729
Rep 1,829
Posts
Drives: '08 E92 M3
Join Date: Jul 2010
Location: Greenville, SC
|
Very nice. I hope it came with instructions. Especially for setting the ring and pinion gear tooth backlash.
__________________
'08 E92 M3 DCT Melbourne Red/Bamboo Beige Leather/EDC/SSP Spec-R DCT clutch discs/SSP Pro-Gold DCT Fluid/Quaife LSD/3:45 Final Drive by Diffs Online/BE Bearings & ARP Bolts/Vibra Technics Engine Mounts/M3 World HFC X-Pipe/LUX H8 180/BPM Sport DCT Tune/PFC Z-Rated Pads/ECS Brass Brake Caliper Bushings/Alex Shop Solid Sub-frame Bushings/Motul 600/Tint
|
Appreciate
1
///M Power-Belgium63328.00 |
08-07-2023, 08:59 AM | #34 |
Private
124
Rep 83
Posts |
Diff and exhaust time
Driveshaft joint , gearbox, flush, lambda sensors new, etc... |
Appreciate
2
DrFerry6728.50 reidetailing600.50 |
08-27-2023, 05:51 AM | #35 |
Private
124
Rep 83
Posts |
Custom fab undertray plate :
|
Appreciate
2
DrFerry6728.50 reidetailing600.50 |
01-12-2024, 06:58 AM | #36 |
Private
124
Rep 83
Posts |
A "little" meet with a rabbit by night on twisty roads with a little speed
One front bumper and some other damages Speed is evil as we often say in France... But that's another debate... then repair Insect Graveyard Close up look of custom undertray plate Other damages Repair, plastics welding Adjusted according to the manufacturer's recommendations US look, so nice but we can't drive without licence plate support in ECE... |
Appreciate
2
reidetailing600.50 DrFerry6728.50 |
01-12-2024, 07:34 PM | #37 |
Field Marshal
6729
Rep 1,829
Posts
Drives: '08 E92 M3
Join Date: Jul 2010
Location: Greenville, SC
|
How is the rabbit? I hear they make for tasty pies - at least in the U.K.
__________________
'08 E92 M3 DCT Melbourne Red/Bamboo Beige Leather/EDC/SSP Spec-R DCT clutch discs/SSP Pro-Gold DCT Fluid/Quaife LSD/3:45 Final Drive by Diffs Online/BE Bearings & ARP Bolts/Vibra Technics Engine Mounts/M3 World HFC X-Pipe/LUX H8 180/BPM Sport DCT Tune/PFC Z-Rated Pads/ECS Brass Brake Caliper Bushings/Alex Shop Solid Sub-frame Bushings/Motul 600/Tint
|
Appreciate
1
///M Power-Belgium63328.00 |
Post Reply |
Bookmarks |
|
|