|
|
02-05-2014, 03:29 PM | #1 |
Banned
13
Rep 602
Posts |
I Help With A No Start Issue
I did a m3 motor swap in my e90 can't seem to firgure out why I'm unable to start her up here are the list of codes pulled. I'm also not able to see ekp in the list of modules in inpa.
[IMG]http://i809.photobucket.com/albums/zz17/***********/9069bca752155727e61cec6543bf3806.jpg[/IMG] [IMG]http://i809.photobucket.com/albums/zz17/***********/0fa4cee3ecc7a989336ef226b81caff4.jpg[/IMG] [IMG]http://i809.photobucket.com/albums/zz17/***********/75fb3650bdac11dc43fca9fe3d809dd9.jpg[/IMG] |
02-05-2014, 05:22 PM | #2 |
BimmerPost Supporting Vendor
3387
Rep 7,541
Posts |
Look @ the module listing with AIF or Ident and see what's responding there.
Clear all of those faults, turn the ignition off, and then back on again. You should see EKP for sure. The EKP module is located behind the rear seat corner on the passenger side.
__________________
-----| Like us on Facebook | Instagram || Tuning Information | Remote Coding |----- ----Visit us at www.BPMSport.com - Emotion. Driven. | Toll Free: (888) 557-5133---- |
Appreciate
0
|
02-05-2014, 05:34 PM | #3 | |
Banned
13
Rep 602
Posts |
Quote:
The ekp is not responding I tried in both inpa and ista I had a few MRS safety codes which I resolved I also haD a terminal 13 CAS code, associated to can pin #7 and #8 that I wasn't able to resolve. I removed pin 7 which cleared the code. |
|
Appreciate
0
|
02-05-2014, 05:38 PM | #4 | ||
BimmerPost Supporting Vendor
3387
Rep 7,541
Posts |
Quote:
Is the CAS, DME and key from the same car? Make sure that you're seeing the ignition pin energize with KL15 on.
__________________
-----| Like us on Facebook | Instagram || Tuning Information | Remote Coding |----- ----Visit us at www.BPMSport.com - Emotion. Driven. | Toll Free: (888) 557-5133---- |
||
Appreciate
0
|
02-06-2014, 06:33 AM | #5 | |
Banned
13
Rep 602
Posts |
Quote:
I'll double check the wire at the ekp do you know what desire voltage should be at the CAN wires? Yes I was told that the motor cas and key are from the same vehicle I'm not getting any errors in ista relating to that. The cas and dme vin#'s are the same the key I'm assuming is correct. KL15 I'm assume is terminal 15 correct? Is it F38 at the junction box pin 19 at cas Or pin 2 at relief relay ? |
|
Appreciate
0
|
05-26-2014, 06:26 PM | #6 |
Banned
13
Rep 602
Posts |
Some help please I'm not sure why ekp is not showing up in inpa AIF list
Or in istaD list Just about ready to give up [IMG]http://i809.photobucket.com/albums/zz17/***********/Mobile%20Uploads/A08A23D1-3A40-4AF9-A449-52B8F31DD384.jpg[/IMG] [IMG]http://i809.photobucket.com/albums/zz17/***********/77A86160-8B21-4A50-9DE3-4F469D3DF306.jpg[/IMG] [IMG]http://i809.photobucket.com/albums/zz17/***********/C060C95A-6C53-44FF-95DD-C4D034980FBC.jpg[/IMG] [IMG]http://i809.photobucket.com/albums/zz17/***********/Mobile%20Uploads/56C1237F-18BD-463B-BC64-9DA2ECAE3627.jpg[/IMG] Last edited by Corpus; 05-26-2014 at 07:04 PM.. |
Appreciate
0
|
05-26-2014, 08:45 PM | #7 |
Private First Class
31
Rep 120
Posts |
check the power wire and the ground wire by the positive boost post on the left side of engine bay. had many of the same codes as well as no start and was cause by the ground cable in the wrong spot. never forget to recheck the simple things to like power grounds and fuses. good luck
|
Appreciate
0
|
05-27-2014, 05:49 AM | #8 | |
Banned
13
Rep 602
Posts |
Quote:
|
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|