Schrick Cams Monday

Bx Tpr · 09-21-2017, 04:25 PM

Wrong machined cam on the Left. Correct machined cam on the right.

MisterEm · 09-21-2017, 05:58 PM

Ruh roh....

How many of these effed up S65 cams are around in vendor stock for us pleebs?

pbonsalb · 09-22-2017, 06:20 AM

Thanks for sharing that. I had been thinking about cams but will wait longer. Schrick screwed up a batch of S52 cams around 13 years ago and someone reported a month ago that S52 Schricks just purchased were not correct. At least with the S52 you could ignore the timing blocks in the back and not use the factory timing tool and instead degree them, but it does not look like that is possible on the S65 Schricks.

SYT_Shadow · 09-22-2017, 09:33 PM

Quote:

Originally Posted by pbonsalb

Thanks for sharing that. I had been thinking about cams but will wait longer. Schrick screwed up a batch of S52 cams around 13 years ago and someone reported a month ago that S52 Schricks just purchased were not correct. At least with the S52 you could ignore the timing blocks in the back and not use the factory timing tool and instead degree them, but it does not look like that is possible on the S65 Schricks.

I'll sell my verified Shrick cams for 10k to whoever wants them

tlow98 · 09-23-2017, 01:25 AM

Quote:

Originally Posted by ilikebmxbikes

going to be good. im going to be running a new Steve Dinan Autotech Cam/valvue springs/ lifters/ Tune in the stroker in the next few months. will be nice to start getting data out.

Nice! Can't wait to see these results. Glad you're pushing the platform and working with Steve's new outfit. Sounds like you'll see some nice top end gains :-)

Does SD Autotech offer the 'old' Dinan stroker motor in its entirety?

///Mobbin · 09-23-2017, 01:07 PM

Quote:

Originally Posted by ilikebmxbikes

going to be good. im going to be running a new Steve Dinan Autotech Cam/valvue springs/ lifters/ Tune in the stroker in the next few months. will be nice to start getting data out.

Sounds amazing!

Curious if SD Autotech might offer this for non-strokers as well?

ilikebmxbikes · 09-23-2017, 11:23 PM

Quote:

Originally Posted by tlow98

Quote:

Originally Posted by ilikebmxbikes

going to be good. im going to be running a new Steve Dinan Autotech Cam/valvue springs/ lifters/ Tune in the stroker in the next few months. will be nice to start getting data out.

Nice! Can't wait to see these results. Glad you're pushing the platform and working with Steve's new outfit. Sounds like you'll see some nice top end gains :-)

Does SD Autotech offer the 'old' Dinan stroker motor in its entirety?

Quote:

Originally Posted by ///Mobbin

Quote:

Originally Posted by ilikebmxbikes

going to be good. im going to be running a new Steve Dinan Autotech Cam/valvue springs/ lifters/ Tune in the stroker in the next few months. will be nice to start getting data out.

The team/ tooling that built the Dinan motors all moved under the SD Autotech brand. Same Dinan motor, same team and same warranty.

Sounds amazing!

Curious if SD Autotech might offer this for non-strokers as well?

The kit works on non stroker - different tune and likely slightly less gains

tlow98 · 09-24-2017, 05:41 PM

Quote:

Originally Posted by ilikebmxbikes

The kit works on non stroker - different tune and likely slightly less gains

Interesting. It seems like this might be the second wave of great NA mods for the S65 platform. Somewhat similar to the S54, it only took 10 years

MisterEm · 09-25-2017, 10:17 AM

Quote:

Originally Posted by ilikebmxbikes

The kit works on non stroker - different tune and likely slightly less gains

Love to see this on your bottom end! Will there be any flowbench data shared with this head?

Aftermarket valvetrain flows much better right out of the box (even STs) for the S65/85 with stock ports... light porting on the exhaust and just a clean up of the machine marks in the intake yields excellent flow results while (most importantly) retaining velocity.

Dave07997S · 09-25-2017, 11:08 AM

Come on 8600rpm, waiting on you bro!! How is it coming along.

Dave

8600RPM · 09-25-2017, 01:45 PM

Car at shop

Dave07997S · 09-25-2017, 02:19 PM

Quote:

Originally Posted by 8600RPM

Car at shop

Nice!!

///Mobbin · 09-29-2017, 04:24 PM

Happy Friday!

Any updates for us??

8600RPM · 09-29-2017, 06:14 PM

My engine exploded...

car was in and still in getting solid subframe bushings, upper control arm monoball bearings dinan. Spherical monoball conversion rear suspension by dinan and spl, car radiator and oil cooler, diff fluid, oil and brake fluid flush, front undercarriage felt replacement.

So anyway, cans in but no car yst

L4ces · 09-30-2017, 06:52 AM

Quote:

Originally Posted by 8600RPM

My engine exploded...

car was in and still in getting solid subframe bushings, upper control arm monoball bearings dinan. Spherical monoball conversion rear suspension by dinan and spl, car radiator and oil cooler, diff fluid, oil and brake fluid flush, front undercarriage felt replacement.

So anyway, cans in but no car yst

Oh no. Sorry that happened! What Caused it cams or something else?

JRV · 09-30-2017, 07:20 AM

Quote:

Originally Posted by L4ces

Quote:

Originally Posted by 8600RPM

My engine exploded...

car was in and still in getting solid subframe bushings, upper control arm monoball bearings dinan. Spherical monoball conversion rear suspension by dinan and spl, car radiator and oil cooler, diff fluid, oil and brake fluid flush, front undercarriage felt replacement.

So anyway, cans in but no car yst

Oh no. Sorry that happened! What Caused it cams or something else?

I thought he was joking

pbonsalb · 09-30-2017, 08:36 AM

I think his project list exploded.

///Mobbin · 09-30-2017, 09:25 AM

Quote:

Originally Posted by 8600RPM

My engine exploded...

car was in and still in getting solid subframe bushings, upper control arm monoball bearings dinan. Spherical monoball conversion rear suspension by dinan and spl, car radiator and oil cooler, diff fluid, oil and brake fluid flush, front undercarriage felt replacement.

So anyway, cans in but no car yst

Nice, should be an enjoyable end product, congrats on getting it all done and looking forward to the cam review.

italyix · 09-30-2017, 04:48 PM

Quote:

Originally Posted by ilikebmxbikes

Quote:

Originally Posted by tlow98

Quote:

Originally Posted by ilikebmxbikes

going to be good. im going to be running a new Steve Dinan Autotech Cam/valvue springs/ lifters/ Tune in the stroker in the next few months. will be nice to start getting data out.

Nice! Can't wait to see these results. Glad you're pushing the platform and working with Steve's new outfit. Sounds like you'll see some nice top end gains :-)

Does SD Autotech offer the 'old' Dinan stroker motor in its entirety?

Quote:

Originally Posted by ///Mobbin

Quote:

Originally Posted by ilikebmxbikes

going to be good. im going to be running a new Steve Dinan Autotech Cam/valvue springs/ lifters/ Tune in the stroker in the next few months. will be nice to start getting data out.

The team/ tooling that built the Dinan motors all moved under the SD Autotech brand. Same Dinan motor, same team and same warranty.

Sounds amazing!

Curious if SD Autotech might offer this for non-strokers as well?

The kit works on non stroker - different tune and likely slightly less gains

As soon as my goodies show up from M24, the SD cams Stage 1 are going in also

jcolley · 10-03-2017, 09:23 PM

Following.

8600RPM · 10-04-2017, 06:41 AM

Picking car up Thursday. Epic tune in hand. Cams in and car runs just fine apparently but it's finishing the other work.

Next is figuring out coilovers. I went backwards than most as that is one of the last things that will get done.

Last will be light aero. I really like the m4 gts wing with higher stations and oem e92 m3 gts front splitter.

I'll be back thursday!

SYT_Shadow · 10-04-2017, 07:19 AM

good!! subscribed!

For suspension, get the MCS 3W and call it a day! You won't regret it

09-21-2017, 04:25 PM	#23
Bx Tpr Captain 123 Rep 891 Posts Drives: 23 CSL Join Date: Feb 2009 Location: NY iTrader: (8)	Wrong machined cam on the Left. Correct machined cam on the right. Attached Images
	Appreciate 1 MisterEm33.00 Quote

09-21-2017, 05:58 PM	#24
MisterEm Second Lieutenant 33 Rep 203 Posts Drives: slow turd Join Date: Sep 2010 Location: huh iTrader: (0)	Ruh roh.... How many of these effed up S65 cams are around in vendor stock for us pleebs?
	Appreciate 0 Quote

09-22-2017, 06:20 AM	#25
pbonsalb Lieutenant General 5231 Rep 10,614 Posts Drives: 18 F90 M5, 99 E36 M3 Turbo Join Date: Feb 2011 Location: New England iTrader: (4)	Thanks for sharing that. I had been thinking about cams but will wait longer. Schrick screwed up a batch of S52 cams around 13 years ago and someone reported a month ago that S52 Schricks just purchased were not correct. At least with the S52 you could ignore the timing blocks in the back and not use the factory timing tool and instead degree them, but it does not look like that is possible on the S65 Schricks.
	Appreciate 1 MisterEm33.00 Quote

09-25-2017, 11:08 AM	#32
Dave07997S Brigadier General 720 Rep 3,964 Posts Drives: 2020 Ford Mustang GT Join Date: May 2009 Location: El Segundo, CA iTrader: (1)	Come on 8600rpm, waiting on you bro!! How is it coming along. Dave __________________ 2020 Ford Mustang GT 6MT PP1 444rwhp (Sold)2013 M3 Coupe-MR/BLK ZCP, 2011 M3 Coupe-MR/Blk 2007 Porsche 997C2S Speed Yellow/Blk sport seats 2004 BMW M3 Imola/Blk
	Appreciate 1 Bx Tpr122.50 Quote

09-25-2017, 01:45 PM	#33
8600RPM Lieutenant Colonel 657 Rep 1,749 Posts Drives: e92 m3 Join Date: Oct 2014 Location: AZ iTrader: (0)	Car at shop
	Appreciate 2 ///Mobbin1478.00 Bx Tpr122.50 Quote

09-29-2017, 04:24 PM	#35
///Mobbin Colonel 1478 Rep 2,672 Posts Drives: m3 Join Date: Jul 2011 Location: Houston iTrader: (3)	Happy Friday! Any updates for us?? __________________ 2021 Alfa Romeo Stelvio Quadrifoglio \| 2.9L \| Trofeo White Tri-Coat \| 8-spd
	Appreciate 0 Quote

09-29-2017, 06:14 PM	#36
8600RPM Lieutenant Colonel 657 Rep 1,749 Posts Drives: e92 m3 Join Date: Oct 2014 Location: AZ iTrader: (0)	My engine exploded... car was in and still in getting solid subframe bushings, upper control arm monoball bearings dinan. Spherical monoball conversion rear suspension by dinan and spl, car radiator and oil cooler, diff fluid, oil and brake fluid flush, front undercarriage felt replacement. So anyway, cans in but no car yst
	Appreciate 0 Quote

09-30-2017, 08:36 AM	#39
pbonsalb Lieutenant General 5231 Rep 10,614 Posts Drives: 18 F90 M5, 99 E36 M3 Turbo Join Date: Feb 2011 Location: New England iTrader: (4)	I think his project list exploded.
	Appreciate 0 Quote

10-03-2017, 09:23 PM	#42
jcolley Lieutenant 378 Rep 413 Posts Drives: 328 Join Date: Jul 2007 Location: Maine iTrader: (1)	Following.
	Appreciate 0 Quote

10-04-2017, 06:41 AM	#43
8600RPM Lieutenant Colonel 657 Rep 1,749 Posts Drives: e92 m3 Join Date: Oct 2014 Location: AZ iTrader: (0)	Picking car up Thursday. Epic tune in hand. Cams in and car runs just fine apparently but it's finishing the other work. Next is figuring out coilovers. I went backwards than most as that is one of the last things that will get done. Last will be light aero. I really like the m4 gts wing with higher stations and oem e92 m3 gts front splitter. I'll be back thursday!
	Appreciate 1 deseroner77.50 Quote

10-04-2017, 07:19 AM	#44
SYT_Shadow ///M Powered for Life 11480 Rep 10,328 Posts Drives: E90M/E92M/M4GTS/M4GT4/X5M Join Date: Sep 2010 Location: Greenwich, CT iTrader: (2)	good!! subscribed! For suspension, get the MCS 3W and call it a day! You won't regret it __________________ DIY: S65 Rod Bearings E9X PFC Z54 BBK on F8X BK harness bar + seats: fit 6 tires in an M3 do88 Cooling Goodies GTS Twins: GTMore project
	Appreciate 0 Quote