|
|
11-02-2021, 02:49 PM | #133 |
Major
1087
Rep 1,395
Posts |
BizzleShniz Check your message settings. I can not reply to your message due to you are not accepting messages!
__________________
E93 M3 6MT , Nav, Prem, Cold Weather, Sports package, & CA, RGBW DTM with RGB Demons + Eisenmann Race + BE + ARP + Brembo GT 380s, $3AG, $5AC, $508, $6NF, $601
Please "Appreciate" If you like my post! DIYs : OEM Camera Retrofit, FLA Retrofit , Drive Shaft Ticking , Starting Issue, , F85 ACC Retrofit |
Appreciate
0
|
11-04-2021, 09:42 PM | #134 |
Major
1087
Rep 1,395
Posts |
BizzleShniz No Luck with your PM Box! Still same issue, I receive your messages but cant respond. Before you buying anything make sure your CIC version is C1A which is the latest version.
If it is not you will need to update it. It requires ICOM cable. And a 30amp battery charger. If you have this 2 i can also update the CIC remotely if you have windows laptop with wifi. I do remote coding all the time not an issue for the OEM camera!
__________________
E93 M3 6MT , Nav, Prem, Cold Weather, Sports package, & CA, RGBW DTM with RGB Demons + Eisenmann Race + BE + ARP + Brembo GT 380s, $3AG, $5AC, $508, $6NF, $601
Please "Appreciate" If you like my post! DIYs : OEM Camera Retrofit, FLA Retrofit , Drive Shaft Ticking , Starting Issue, , F85 ACC Retrofit |
Appreciate
0
|
11-05-2021, 04:03 PM | #135 |
New Member
11
Rep 10
Posts |
I am updated to C1A. I also just finished combox for TCU/MULF. I have some familiarity with coding at this point as well as VO changes. As far as the camera goes I am a little concerned with swapping out my JBE and subsequent coding. I don't have ICOM or a battery charger either. I don't know if that is required or not. I got the Master version to replace my H1 version.
|
Appreciate
0
|
01-19-2022, 10:10 PM | #137 | |
Major
1087
Rep 1,395
Posts |
Quote:
__________________
E93 M3 6MT , Nav, Prem, Cold Weather, Sports package, & CA, RGBW DTM with RGB Demons + Eisenmann Race + BE + ARP + Brembo GT 380s, $3AG, $5AC, $508, $6NF, $601
Please "Appreciate" If you like my post! DIYs : OEM Camera Retrofit, FLA Retrofit , Drive Shaft Ticking , Starting Issue, , F85 ACC Retrofit |
|
Appreciate
0
|
01-23-2022, 05:54 AM | #138 |
New Member
17
Rep 11
Posts |
Just incase anyone else is looking for dump data on E90/E84 PDC, here's my conversion bundle of back-up binaries and extra's.
https://mega.nz/file/KU4hUKzY#wup7YP...n3rzctbj4xPafs |
Appreciate
2
shannon1655.50 johnnyorange58.50 |
01-23-2022, 06:23 AM | #139 |
New Member
17
Rep 11
Posts |
FYI - though the TRSVC70 works 'out of the box' so to speak, default coding it won't accomplish anything as it was never intended for this platform. If you do want to code it for greater precision (and this is entirely optional), I covered this in more detail in an older post.
https://www.m3post.com/forums/showth...7#post26409397 Pre-requisites to do this are, a JBE3 (you won't be able to code it with a JBE2 installed), and an ICOM or a hacked ediabas/K+DCAN cable. |
02-11-2022, 04:54 PM | #141 | |
Major
1087
Rep 1,395
Posts |
Quote:
TRSVC from E70s comes with side view camera ports and if you have that one still works with the ONLY rear view but throws error on ISTA since side mirrors are missing.
__________________
E93 M3 6MT , Nav, Prem, Cold Weather, Sports package, & CA, RGBW DTM with RGB Demons + Eisenmann Race + BE + ARP + Brembo GT 380s, $3AG, $5AC, $508, $6NF, $601
Please "Appreciate" If you like my post! DIYs : OEM Camera Retrofit, FLA Retrofit , Drive Shaft Ticking , Starting Issue, , F85 ACC Retrofit |
|
Appreciate
0
|
03-01-2022, 01:46 PM | #142 | |
Registered
8
Rep 4
Posts |
Quote:
After installing the modified module, I was able to read its status/identity with INPA and read the coding data with NCS Expert, but no matter what I tried, writing new coding data would always fail with ERROR_ECU_DOWNLOAD_NOT_ACCEPTED. Coding was a necessity since the EEPROM dump from SyphonX was coded for 8 sensors and no camera. Without front sensors, the rear sensors stop working after a few seconds (don't ask me why...) and without the RVC option, the camera doesn't get activated. After screwing with it all weekend trying to get coding to work the normal way, I decided to try to figure out how to write the coding data directly to the EEPROM. With a little bit of detective work, here's how I did it: Using the NETTODAT file I was able to read from the module, I was able to map each coding section to an address in EEPROM: Code:
Varianten_Kodierung (0x00300000, 2 bytes): 0x5D Fahrzeug_Konfiguration (0x00300100, 15 bytes): 0x60 Wandler_Cfg_hinten (0x00300200, 22 bytes): 0x73 Wandler_Cfg_vorne (0x00300300, 22 bytes): 0x8A Schwellwert_Ecke_hinten (0x00300400, 10 bytes): 0xA1 Schwellwert_Mitte_hinten (0x00300500, 10 bytes): 0xAC Schwellwert_Ecke_vorne (0x00300600, 10 bytes): 0xB7 Schwellwert_Mitte_vorne (0x00300700, 10 bytes): 0xC2 Totzeit_Echos (0x00300800, 6 bytes): 0xCD Frequenz_Konfiguration (0x00300900, 2 bytes): 0x70 Parkmaster (0x00300B00, 17 bytes): 0xD4 Also, for completeness sake, the last 7 digits of the VIN are stored in ASCII at 0x3B Using NCS Dummy, I was able to determine what each value needed to be set to for my e92 with only the rear sensors and RVC enabled. I then recalculated the checksums and flashed it to the EEPROM with the XPROG. Then, much to my surprise, everything was working correctly. I'm still not sure why I wasn't able to write to the modified module. I suspect either the AliExpress MCU I got is a knockoff/reject and has some issue with writing to EEPROM, or maybe there's some sort of protocol difference with the e84 module that my JBE doesn't know how to handle. For anyone who may be interested, I've attached my EEPROM bin which is configured for a pre-lci e92 335i with only rear sensors, m sport bumpers, and rearview camera. |
|
Appreciate
3
|
03-01-2022, 01:59 PM | #143 |
New Member
23
Rep 23
Posts |
I got my harness today to do the wiring. The can cables run the full length up to the front of the car. Before I dig in to cable this, is there a place to tap into the can under the dash, or did most people tap the can right off the pdc module in the rear?
|
Appreciate
0
|
03-01-2022, 02:03 PM | #144 |
Registered
8
Rep 4
Posts |
I tapped mine into the CAN wires going into the CIC unit, which is how I think it is intended to be done.
|
Appreciate
0
|
03-01-2022, 08:53 PM | #146 | |
Major
1087
Rep 1,395
Posts |
That is a great find. Can you also make this with 8 sensor not just 4 sensor rear? Because it is codable option and you can run a Front and Rear PDC module with only rear enabled. No need to disable from the eeprom. But the RVC option being injected in to E9x PDC is the important part of this flash! Thank you for your input.
Quote:
__________________
E93 M3 6MT , Nav, Prem, Cold Weather, Sports package, & CA, RGBW DTM with RGB Demons + Eisenmann Race + BE + ARP + Brembo GT 380s, $3AG, $5AC, $508, $6NF, $601
Please "Appreciate" If you like my post! DIYs : OEM Camera Retrofit, FLA Retrofit , Drive Shaft Ticking , Starting Issue, , F85 ACC Retrofit |
|
Appreciate
0
|
03-11-2022, 09:23 AM | #147 |
New Member
23
Rep 23
Posts |
So, I have everything wired up fpr this retrofit. The e70 trsvc unit and camera are just sitting in the trunk for testing, but plugged in.
The vo option has been added. The cic module coding is done. Pdc was default coded with the provided files. When I put the car in reverse I get the pdc on the right hand side of the screen. And it also shows the pdc in the center not camera. I do have the park menu on the left side, but everything is grayed out. I double checked all the coding and everything is there. I'm stumped now. Maybe someone knows what's wrong. I did notice when I use ncs and process the cic it shows cic.c08 but when I execute a read job it changes to cic.c1a. Is there a better way to check the firmware version? Now I'm questioning if it is c1a or c08. |
Appreciate
0
|
03-11-2022, 02:58 PM | #148 | |
Major
1087
Rep 1,395
Posts |
Quote:
__________________
E93 M3 6MT , Nav, Prem, Cold Weather, Sports package, & CA, RGBW DTM with RGB Demons + Eisenmann Race + BE + ARP + Brembo GT 380s, $3AG, $5AC, $508, $6NF, $601
Please "Appreciate" If you like my post! DIYs : OEM Camera Retrofit, FLA Retrofit , Drive Shaft Ticking , Starting Issue, , F85 ACC Retrofit |
|
Appreciate
0
|
03-12-2022, 12:07 AM | #149 | |
New Member
23
Rep 23
Posts |
Quote:
Okay awesome so at least the cic is c1a. I have the e84 pdc with matching part number from the write up. I double checked that I dropped the provided files in the correct place and default coded it again. I thought the TRSVC worked without coding, but you need ICOM if you actually want to code it? |
|
Appreciate
0
|
03-13-2022, 01:14 AM | #150 | |
Major
1087
Rep 1,395
Posts |
Quote:
There must be something u re doing wrong or camera module is bad. I cant think of anything else.
__________________
E93 M3 6MT , Nav, Prem, Cold Weather, Sports package, & CA, RGBW DTM with RGB Demons + Eisenmann Race + BE + ARP + Brembo GT 380s, $3AG, $5AC, $508, $6NF, $601
Please "Appreciate" If you like my post! DIYs : OEM Camera Retrofit, FLA Retrofit , Drive Shaft Ticking , Starting Issue, , F85 ACC Retrofit |
|
Appreciate
0
|
03-13-2022, 09:34 AM | #151 |
New Member
23
Rep 23
Posts |
Cool! I'm going to go back over everything and test all the wiring. I'll let you know what kind of user error I find.
|
Appreciate
0
|
03-13-2022, 10:10 AM | #152 |
Major
1087
Rep 1,395
Posts |
Allright, Always here to help.
__________________
E93 M3 6MT , Nav, Prem, Cold Weather, Sports package, & CA, RGBW DTM with RGB Demons + Eisenmann Race + BE + ARP + Brembo GT 380s, $3AG, $5AC, $508, $6NF, $601
Please "Appreciate" If you like my post! DIYs : OEM Camera Retrofit, FLA Retrofit , Drive Shaft Ticking , Starting Issue, , F85 ACC Retrofit |
Appreciate
0
|
03-13-2022, 11:53 AM | #153 |
New Member
23
Rep 23
Posts |
I appreciate it! And thanks to everyone that contributed to this awesome retrofit!
I went to check the wiring and one of the m connectors didn't get compressed all the way. So a CAN wire had pulled out. Got that fixed and the camera displayed immediately. |
Appreciate
1
SaNGRia1086.50 |
03-13-2022, 01:00 PM | #154 |
Major
1087
Rep 1,395
Posts |
Yeap, that is exactly what i thought. I am glad you sorted out. The best OEM Mode you can ever see on E series is this!
__________________
E93 M3 6MT , Nav, Prem, Cold Weather, Sports package, & CA, RGBW DTM with RGB Demons + Eisenmann Race + BE + ARP + Brembo GT 380s, $3AG, $5AC, $508, $6NF, $601
Please "Appreciate" If you like my post! DIYs : OEM Camera Retrofit, FLA Retrofit , Drive Shaft Ticking , Starting Issue, , F85 ACC Retrofit |
Appreciate
0
|
Post Reply |
Bookmarks |
|
|