|
|
12-30-2020, 04:23 PM | #133 | |
Brigadier General
4095
Rep 4,341
Posts |
Quote:
|
|
Appreciate
1
jvictormp935.50 |
12-30-2020, 04:34 PM | #134 | ||
First Lieutenant
287
Rep 304
Posts |
Quote:
|
||
Appreciate
0
|
12-30-2020, 04:42 PM | #135 |
Lieutenant General
5611
Rep 11,072
Posts |
Maybe the vendors got worried and did that. Some say Deep State stuff like this happens. You don’t need any proof to make a claim like that.
|
Appreciate
3
|
01-06-2021, 09:08 AM | #136 |
Lieutenant
405
Rep 527
Posts |
Here's what sweep we get with Alfa 6 pot Brembo, GT500 Yellow stuff pads and M4 rotors. Note the outside sweep is flush just was wiggly to hold it to take the picture.
Awaiting freakyparts brackets, been a month and still waiting. |
Appreciate
2
Epoustouflant1164.00 SilverSlug692.00 |
01-06-2021, 11:51 AM | #137 | |
Captain
936
Rep 839
Posts |
Quote:
Anyway, I gave up on it, and bought the M3 zimmermann discs. It will be an eternity for it to arrive here in Brazil, though. I figured out that my rear discs are M3 E46's. Only rears. Now, has somebody heard about fitting the M3 E46 rear discs on the E92? I'm asking because I'm afraid of needing to undo any adapting previous owner may have made. |
|
Appreciate
0
|
01-26-2021, 07:17 AM | #139 |
Lieutenant
405
Rep 527
Posts |
Anyone seen these? Replacement 2-pc rotors for M3/M4. Reasonably priced too.
Could be a solution for those wanting to gain some extra thermal capacity with larger calipers. https://paragonbrakes.com/2-piece-ro...4-f82-f83.html |
Appreciate
0
|
01-27-2021, 05:20 AM | #141 |
Lieutenant
405
Rep 527
Posts |
|
Appreciate
0
|
01-27-2021, 07:52 AM | #144 | |
First Lieutenant
296
Rep 367
Posts |
Quote:
|
|
Appreciate
0
|
01-27-2021, 08:32 AM | #145 | |
Banned
1164
Rep 450
Posts |
Quote:
|
|
Appreciate
1
CTMike295.50 |
01-27-2021, 10:14 AM | #146 |
Lieutenant
405
Rep 527
Posts |
Here's my full setup ready to install.
Front: Alfa Romeo Giulia Stelvio Quadrifoglio Brembo 6 Pot calipers, EBC Yellow pads D1666 (Part # DP43013R) Freaky parts brackets with 10mm shims, HEL braided lines and OEM F80 380mm rotors. Rear: OEM F80 370mm rotors and OEM F80 rear calipers. I need to build up the calipers after I was done refinishing (High temp paint) with nipples, hardline etc... Will likely black out the backside of the EBC pads, the yellow clashes with the red for my taste. Last edited by UnicornM; 01-27-2021 at 10:22 AM.. |
Appreciate
5
|
01-27-2021, 11:09 AM | #147 | |
Banned
1164
Rep 450
Posts |
Quote:
You got a tally? |
|
Appreciate
1
UnicornM404.50 |
01-27-2021, 12:07 PM | #149 |
Banned
1164
Rep 450
Posts |
|
Appreciate
0
|
01-27-2021, 12:15 PM | #151 |
Banned
1164
Rep 450
Posts |
|
Appreciate
0
|
01-27-2021, 12:42 PM | #152 | |
Captain
215
Rep 811
Posts |
Quote:
What kind of paint/primer did you use?
__________________
2011 BMW E92 M3
2018 Tesla Model 3 Long Range RWD |
|
Appreciate
1
UnicornM404.50 |
01-27-2021, 02:32 PM | #153 | |
Lieutenant
405
Rep 527
Posts |
Quote:
Primer wasn't needed as the OEM finish was rubbed down with 400 grit/red scotch then straight to base which was RAL3020 followed by 2k lacquer. Ive done it this way in the past with great results |
|
Appreciate
0
|
01-27-2021, 02:50 PM | #154 | |
Captain
215
Rep 811
Posts |
Quote:
I'm looking to do front only(probably going to do it around late Spring early Summer) and go with StopTech ST40, while the saving isn't much compared to ST40 on sale, the ability to pick your own color and use FCP Euro for unlimited front rotor replacement is still nice. In one of the pics you posted earlier, I saw the caliper was all dark gray, what was that dark gray caliper if not primer?
__________________
2011 BMW E92 M3
2018 Tesla Model 3 Long Range RWD |
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|