|
|
06-23-2022, 08:09 PM | #573 | |
Major
134
Rep 1,365
Posts |
Quote:
That would be very gracious of you and I'll for sure return it. I had to replace my original idler pulley (was making screeching noise) and the other two tensioner pulleys so next is to do my plugs. I was going to attempt to do without but if you are willing to send it to me, I'll hold off till then. Please pm me and I'll reply. Very much appreciated!! RB |
|
Appreciate
0
|
06-23-2022, 09:23 PM | #574 | |
Captain
371
Rep 860
Posts |
Quote:
|
|
Appreciate
0
|
06-23-2022, 11:18 PM | #575 |
Major
1816
Rep 1,250
Posts
Drives: 2009 E92 M3 Dakar Yellow II
Join Date: Oct 2021
Location: Edmonds, WA
|
I bought a windshield wiper puller from Amazon as suggested and a couple minutes with a grinder gave me an adequate coil puller. Coupled with a KoKen spark plug socket and I managed to get the job done.
|
Appreciate
0
|
06-24-2022, 12:10 AM | #576 | |
Major
134
Rep 1,365
Posts |
Quote:
RB |
|
Appreciate
0
|
06-24-2022, 04:10 AM | #578 | |
Major
1816
Rep 1,250
Posts
Drives: 2009 E92 M3 Dakar Yellow II
Join Date: Oct 2021
Location: Edmonds, WA
|
Quote:
Keep in mind you will have to thin the arms down a little with a file or grinder. I think I took about a millimeter off |
|
Appreciate
1
Erickuokwa502.50 |
06-24-2022, 09:39 PM | #580 |
Captain
371
Rep 860
Posts |
PM Received. Loaner tool shipped out today. Best of luck man! I've changed plugs 3 times on this car so I'm no expert, but if I can help let me know!
__________________
|
Appreciate
0
|
06-24-2022, 10:26 PM | #581 |
Major
1816
Rep 1,250
Posts
Drives: 2009 E92 M3 Dakar Yellow II
Join Date: Oct 2021
Location: Edmonds, WA
|
How do you go about extracting the driver side back coil? That hung me up for 30 minutes before I somehow got it right. I don't recall exactly what I did. Getting it back in was nearly as bad
|
Appreciate
0
|
06-24-2022, 10:34 PM | #582 |
Weirdo
460
Rep 192
Posts |
|
Appreciate
0
|
06-24-2022, 10:34 PM | #583 | |
Major
1816
Rep 1,250
Posts
Drives: 2009 E92 M3 Dakar Yellow II
Join Date: Oct 2021
Location: Edmonds, WA
|
Quote:
|
|
Appreciate
0
|
06-25-2022, 12:03 PM | #585 |
Weirdo
460
Rep 192
Posts |
|
Appreciate
0
|
06-25-2022, 09:05 PM | #586 |
Captain
371
Rep 860
Posts |
It's a tight fit. I usually spin the pack until the connector is at an angle that allows it to clear and then rotate it to the proper position once clear. The rubber at the bottom has a little give to it which also helps for that last 1/4 inch.
__________________
|
Appreciate
0
|
06-26-2022, 01:58 AM | #587 | |
Major
134
Rep 1,365
Posts |
Quote:
|
|
Appreciate
0
|
11-27-2022, 11:20 AM | #588 |
Private First Class
14
Rep 127
Posts |
Rumor has it the Division M Coil Pulling tools will be back in stock in the very near future:
https://www.amazon.com/dp/B00J9P0TYE https://www.amazon.com/dp/B01GZ3XZQG Sorry for the hiatus.... |
Appreciate
0
|
Post Reply |
Bookmarks |
|
|