|
|
04-18-2020, 02:23 PM | #11816 |
Lieutenant Colonel
4102
Rep 1,612
Posts |
|
Appreciate
0
|
04-18-2020, 08:21 PM | #11817 |
Lieutenant General
11593
Rep 12,738
Posts |
A little more lightness was added today for my non-instagram peeps. Ditched the rear trunk panels and added some titanium hardware to my Cusco body brace. Even if you don't have the Cusco brace, you have these body braces in place and the three torx bolts are oem. Also finished the engine bay hardware (steering reservoir was previously incomplete). I also ditched the battery bar since it was designed to keep the oem 55lb battery in place in the event of an accident. It is non structural.
I'm going back for the carpet back there, ran out of time today. Just a little over 9lbs shed today.
__________________
Instagram; @roastbeefmike
|
Appreciate
0
|
04-18-2020, 09:15 PM | #11818 |
Lieutenant General
11593
Rep 12,738
Posts |
@Grip Addict
__________________
Instagram; @roastbeefmike
|
Appreciate
1
Grip Addict1081.50 |
04-18-2020, 09:52 PM | #11820 |
Lieutenant General
11593
Rep 12,738
Posts |
you'll want four m6-1x50mm hex flange bolts. and four washers- m6 fender washers, 1mm thick with 19mm outer diameter. they fit perfect.
__________________
Instagram; @roastbeefmike
|
Appreciate
1
Grip Addict1081.50 |
04-18-2020, 10:16 PM | #11821 | |
Banned
1082
Rep 713
Posts |
Quote:
Also this? https://www.ti64.com/product-p/6499.htm |
|
Appreciate
0
|
04-18-2020, 10:25 PM | #11822 | ||
Lieutenant General
11593
Rep 12,738
Posts |
Quote:
__________________
Instagram; @roastbeefmike
|
||
Appreciate
2
Grip Addict1081.50 StripclubDJ4101.50 |
04-18-2020, 10:39 PM | #11823 |
Banned
1082
Rep 713
Posts |
|
Appreciate
0
|
04-18-2020, 10:58 PM | #11824 | |
Lieutenant General
11593
Rep 12,738
Posts |
Quote:
__________________
Instagram; @roastbeefmike
|
|
Appreciate
2
Grip Addict1081.50 StripclubDJ4101.50 |
04-18-2020, 11:01 PM | #11825 |
Banned
1082
Rep 713
Posts |
|
04-18-2020, 11:02 PM | #11826 |
Lieutenant General
11593
Rep 12,738
Posts |
i'm just an idiot with a thread checker and too much time on my hands bro.
__________________
Instagram; @roastbeefmike
|
Appreciate
3
|
04-18-2020, 11:26 PM | #11828 |
Major General
2468
Rep 5,932
Posts |
The curves presented are not based on actual testing. Theses curves were analytically predicted using a CFD analysis. The results are only as good as the assumptions used in the analysis - GIGO. Without performing some type of correlation between analytical results and test data then you do not know how accurate the predicted results are. Just be careful when stating something is based on “testing” when it actually has absolutely nothing to do with real world testing.
|
Appreciate
0
|
04-18-2020, 11:32 PM | #11829 | |
Major General
2468
Rep 5,932
Posts |
Quote:
|
|
Appreciate
0
|
04-19-2020, 11:29 AM | #11831 |
Major
1134
Rep 1,366
Posts |
Anything easier these stupid KW ones is a win! Would love the GC one but $400 is a tough pill to swallow on them lol. Glad to know the BW one is a good buy too.
__________________
#ladydriven Heavy-spec M3 // KW Clubsports // AA x-pipe // Gintani muffler // Macht-Schnell intake // Gintani tune // OMP Seats // Too Many Apex Wheels // Stoptech ST-60 // Cobalt Friction brake pads |
Appreciate
0
|
04-19-2020, 12:45 PM | #11832 |
Major General
2468
Rep 5,932
Posts |
I understand. Unfortunately for me, the GC articulating rear spring perch was released just a few weeks after buying the BW rear height adjusters for the M4 a few years back. However, I wouldn’t have bought multiple versions of the same BW adjusters if I didn’t like them. I’m swapping the rear setup on the M4 to a true coilover setup this spring-summer.
|
Appreciate
2
SYT_Shadow11511.00 Kelse921133.50 |
04-19-2020, 01:46 PM | #11833 | |
///M Powered for Life
11511
Rep 10,342
Posts |
Quote:
|
|
Appreciate
1
M3SQRD2468.00 |
04-19-2020, 01:59 PM | #11834 |
Major General
2468
Rep 5,932
Posts |
|
Appreciate
1
SYT_Shadow11511.00 |
04-20-2020, 01:09 AM | #11835 |
Lieutenant Colonel
1073
Rep 1,617
Posts |
Got a little fun feature from my favorite HPDE org
https://www.speedsf.com/blog/2020/4/...ofiles-ken-yip |
04-20-2020, 02:46 PM | #11836 |
.
1966
Rep 1,925
Posts
Drives: E92 M3
Join Date: Oct 2016
Location: MN
|
Unless I'm missing something, 265/660-18 Pirelli slicks should fit my 18" Apex EC7 square setup on stock ZCP suspension, right?
275/35-18 NT01s rub a little up front close to full lock but that's not a worry on track. |
Appreciate
0
|
Post Reply |
Bookmarks |
|
|