|
|
07-14-2019, 10:05 AM | #1 |
Lieutenant
229
Rep 415
Posts |
Brake Booster Sensor after Brake Flush?
Guys,
Just wanted to confirm with everyone if this is indeed my issue or not: I did my brake flush and that lead to a small leak around the reservoir cap. After 10 days got reduced engine power with increased emissions. Adding codes below - based on my research it seems quite clear that it is the brake booster sensor. Just need to understand why I am getting the Increased Emission? How can that be related to Brake Booster Sensor? |
07-14-2019, 11:42 AM | #3 |
mTekMods
2249
Rep 2,995
Posts |
Yeah I fixed One of these yesterday, it’s common that brake fluid spills onto the sensor which is directly below the reservoir and the sensor is rendered garbage and causes limp mode.
Changing the sensor involves changing the vacuum pipe because it comes with the pipe. The TIS directions indicate removing the reservoir and the master cylinder but I was Able to change it without doing this. It is a bit harder but you won’t have to bleed the brakes again. With the engine off press the brake a couple times to get out the vacuum in the system. Remove the clamp connecting the pipe to the engine vacuum pipe, it’s a one time clamp. You’ll need a pick to unclog the sensor and another pick to pull the connector back. Remove the end going into the brake booster with a long flat head then undo the end of it near the fender. Push in the blue release and pull it out. To get the engine line out will take some patience, you’ll need to slip it under the booster then out the drivers side. |
Appreciate
1
330ciprem228.50 |
07-14-2019, 01:43 PM | #4 | |
Lieutenant
229
Rep 415
Posts |
Quote:
One question - the clamp connnecting the pipe to engine vacuum pipe is a one a time clamp so do I need to order that or is that something that comes part of the booster assembly I am gonna order? Last edited by 330ciprem; 07-14-2019 at 02:27 PM.. |
|
Appreciate
0
|
07-14-2019, 02:44 PM | #5 |
Major
11486
Rep 1,065
Posts |
The alternative is to just replace the sensor itself. 2 Torx screws and a lot of patience. I have done it that way without removing the lines at all. You would need a long wobble extension, a long screwdriver to push the sensor over a little to get to the torx bolts and an extendable magnet. Took me about 30 minutes.
__________________
E46, E60 M5, E93 M3, F15 X5
IG - @thebimmerhaus |
07-14-2019, 06:54 PM | #6 |
mTekMods
2249
Rep 2,995
Posts |
11151726339 That’s the part number, it requires a special tool to crimp it.
|
Appreciate
0
|
07-14-2019, 09:29 PM | #9 |
Major
11486
Rep 1,065
Posts |
Here is a thread with some good tips. It isn't that difficult with the right tools and some finesse.
https://www.m3post.com/forums/showthread.php?t=1338052
__________________
E46, E60 M5, E93 M3, F15 X5
IG - @thebimmerhaus |
Appreciate
0
|
07-15-2019, 01:16 AM | #10 |
Driver
2695
Rep 2,715
Posts |
Using long needle-nose pliers, a telescoping magnet, a swivel socket on an extension, and the appropriate torx bit, you can remove and replace the sensor in 10-30 min with the only items removed being the cowl cover and the brake fluid reservoir cover. You will also want to un-clip the partition which the vacuum line runs through (just to the left of the reservoir). Then you can move the line to move the sensor, and reach the torx screws. Use the magnet to remove and replace the torx screws. It isn't that bad.
__________________
E90M 6MT Slicktop Single Humper in need of a diet
|
07-15-2019, 03:01 AM | #11 |
Colonel
3579
Rep 2,828
Posts |
Is it possible to mess with this sensor and not throw a code? I ask because I often hear a buzzing sound when I’m on the brakes, far more often than I think I should. My car feels/brakes just fine and the brakes, while near end of life, are within spec check out. No codes, just not sure if this buzzing is normal. It’s been like this since I got the car (1 year, 3K), and it had a brake flush right before.
|
Appreciate
0
|
07-15-2019, 04:48 AM | #12 | |
mTekMods
2249
Rep 2,995
Posts |
Quote:
|
|
Appreciate
0
|
07-15-2019, 06:03 AM | #13 |
Lieutenant
229
Rep 415
Posts |
1 stupid question:
Do I need to slightly remove brake fluid from the reservoir to do this job? Or can I leave the cap on and just move it? |
Appreciate
0
|
07-15-2019, 06:24 AM | #14 |
Major
11486
Rep 1,065
Posts |
No need to do so. It will not effect the fluid level at all. That said, if it is overfilled from when you flushed the system, get it down to the max level. Other than that you are good.
__________________
E46, E60 M5, E93 M3, F15 X5
IG - @thebimmerhaus |
07-15-2019, 11:20 AM | #15 | |
Driver
2695
Rep 2,715
Posts |
Quote:
__________________
E90M 6MT Slicktop Single Humper in need of a diet
|
|
Appreciate
1
Dpc2u11486.00 |
07-15-2019, 11:36 AM | #17 |
Colonel
3579
Rep 2,828
Posts |
Thanks, probably the sensor. Works fine but I hear the buzzing more than I think I should be. Given that it works fine, is this something I should address ASAP (risk of some runaway damage) or is waiting until my next brake job okay (if I am otherwise fine with the buzzing)?
|
Appreciate
1
Dpc2u11486.00 |
07-15-2019, 12:10 PM | #18 |
Major
11486
Rep 1,065
Posts |
Actually, just the opposite. If you were to feel an effect from a bad sensor, it would be a harder pedal due to the fact that the brake booster is starved for vacuum. Performance engines don't make sufficient vaccum so manufacturers add a vacuum pump to increase vacuum on the booster. When the sensor and secondary pump is working properly, you will only only hear the pump run on occasion for short periods of time, and only noticeably when you first hit the brakes after a start, like when backing out of a garage.
__________________
E46, E60 M5, E93 M3, F15 X5
IG - @thebimmerhaus |
Appreciate
0
|
07-15-2019, 12:30 PM | #19 | |
Major
11486
Rep 1,065
Posts |
Quote:
__________________
E46, E60 M5, E93 M3, F15 X5
IG - @thebimmerhaus |
|
Appreciate
0
|
07-15-2019, 02:00 PM | #20 | |
Driver
2695
Rep 2,715
Posts |
Quote:
__________________
E90M 6MT Slicktop Single Humper in need of a diet
|
|
Appreciate
1
Dpc2u11486.00 |
07-15-2019, 02:46 PM | #21 | |
Major
350
Rep 1,100
Posts
Drives: Melbourne Red e90 M3
Join Date: Jul 2012
Location: Bellevue, WA
|
Quote:
No codes, but expecting it to get worse, when it hasn't.
__________________
6MT | 11:1 Forged 4.1L | ESS-G1 | KW ClubSport | Sparta 380/355 BBK
|
|
Appreciate
0
|
07-15-2019, 04:23 PM | #22 |
mTekMods
2249
Rep 2,995
Posts |
I havent Heard my pump run since April when it was still cold out.
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|