BMW M3 Forum (E90 E92)

BMW Garage BMW Meets Register Today's Posts


Go Back   M3Post - BMW M3 Forum > E90/E92 M3 Technical Topics > DIY Guides/ Discussions
 
BPM
Post Reply
 
Thread Tools Search this Thread
      02-08-2013, 05:37 PM   #23
Ausdino
Registered
Ausdino's Avatar
0
Rep
3
Posts

Drives: 2008 E92 M3
Join Date: Feb 2013
Location: Brisbane Australia

iTrader: (0)

Great writeup. This will make installing the Remus exhaust a lot easier...
cheers
Appreciate 0
      03-19-2013, 05:41 PM   #24
PhoenixRising
Important text here
United_States
24
Rep
130
Posts

Drives: 2013 M3 Conv
Join Date: Dec 2012
Location: Phoenix, AZ

iTrader: (0)

Garage List
Can't wait to use this to install the exhaust that's on the way!
__________________

2009 AM V8 Vantage Conv - Berwick Bronze, Quicksilver Exhaust
2013 M3 Conv - (RIP) thanks to uninsured a-hole
2004 Porsche 911 C4S Conv
Appreciate 0
      03-31-2013, 08:55 AM   #25
PhoenixRising
Important text here
United_States
24
Rep
130
Posts

Drives: 2013 M3 Conv
Join Date: Dec 2012
Location: Phoenix, AZ

iTrader: (0)

Garage List
This was such an easy upgrade thanks to this writeup. Not intimidating at all! I didn't end up removing any bottom covers past the large aluminum plate. The last 2 plate bolts were under a plastic cover but it was flexible enough to get my hand and a wrench in there. I was done in about 90 minutes.

Best part? No leftover bolts! Haha

The Active Autowerke exhaust sounds amazing and the BPMSport stage 2 tune took care of the CEL that was thrown about a week later.

Thanks for the DIY!
__________________

2009 AM V8 Vantage Conv - Berwick Bronze, Quicksilver Exhaust
2013 M3 Conv - (RIP) thanks to uninsured a-hole
2004 Porsche 911 C4S Conv
Appreciate 0
      05-11-2013, 04:34 PM   #26
Dominic_M
Second Lieutenant
Dominic_M's Avatar
15
Rep
255
Posts

Drives: 08 ///M3 and 2014 535i
Join Date: Feb 2009
Location: Atlanta, GA

iTrader: (0)

Great ... Just what I needed.
__________________
2008 E90 M3 SPARKLING GRAPHITE METALLIC
Appreciate 0
      06-10-2013, 12:38 PM   #27
Transfer
Major General
Transfer's Avatar
5294
Rep
5,875
Posts

Drives: Bronco Wildtrak, Tesla MYP
Join Date: Mar 2010
Location: Issaquah, WA

iTrader: (1)

Need help. In pictures 14 and 15 showing the rear bracket, what size screw heads are on there? It's sort of a reverse Torx or something. I can't get it off and need more detail. I tried with a 12 point 5/16" and 8mm and it's crazy tight and started stripping. Anyone know EXACTLY what the bolt head is?
Appreciate 0
      06-10-2013, 01:17 PM   #28
PhoenixRising
Important text here
United_States
24
Rep
130
Posts

Drives: 2013 M3 Conv
Join Date: Dec 2012
Location: Phoenix, AZ

iTrader: (0)

Garage List
You're right, it's a reverse Torx. Your local auto parts store will have them. I think it was a 16? I can't be sure, but yeah don't try any other socket other than the correct Torx. You'll round it off.
__________________

2009 AM V8 Vantage Conv - Berwick Bronze, Quicksilver Exhaust
2013 M3 Conv - (RIP) thanks to uninsured a-hole
2004 Porsche 911 C4S Conv
Appreciate 0
      06-14-2013, 01:28 AM   #29
Transfer
Major General
Transfer's Avatar
5294
Rep
5,875
Posts

Drives: Bronco Wildtrak, Tesla MYP
Join Date: Mar 2010
Location: Issaquah, WA

iTrader: (1)

For reference, I've determined it's an E10 socket.
Appreciate 0
      08-17-2013, 05:55 AM   #30
pkimM3r
Banned
pkimM3r's Avatar
220
Rep
7,298
Posts

Drives: m3 saloon in granny mode.
Join Date: Dec 2009
Location: lost angeles

iTrader: (0)

Header back is a whole new story. I took off a system on an e92 with ease and then on my car an e90 the undertray wouldnt come off?!
Appreciate 0
      09-14-2013, 04:45 PM   #31
srtoad4
First Lieutenant
94
Rep
349
Posts

Drives: 2014 CP M5 / 2016 SRT Jeep
Join Date: Aug 2013
Location: Phoenix, AZ

iTrader: (2)

Does anyone know the part number for those red urethane hangers by the secondary cats (same ones that are up front)? Can't find a part number for the life of me.
__________________
14 Space Grey CP M5 / CCB / Exec / etc
BMS Stage 1 / Charcoal Delete / K&Ns / Catless OEM DP & Borla S-Type Catback
Appreciate 0
      09-16-2013, 01:42 PM   #32
N1tr0gen
Private First Class
N1tr0gen's Avatar
5
Rep
153
Posts

Drives: M3Vert
Join Date: Jul 2013
Location: Canada

iTrader: (1)

Thanks for this write up! Helped me a ton. I do have an E93 and I had to unscrew the big middle bolt and the 2 smaller ones closer to the wheels to give the reinforcement brace enough flexibility to slide the exhaust out, rest is easy!
Appreciate 0
      09-17-2013, 02:36 PM   #33
psk278
New Member
0
Rep
8
Posts

Drives: 08 M3 6MT
Join Date: Aug 2013
Location: United States

iTrader: (0)

This tool will make your life easier when dealing with exhaust hangers:

http://www.amazon.com/Lisle-38350-Ex...st+hanger+tool
Appreciate 0
      09-18-2013, 05:39 PM   #34
srtoad4
First Lieutenant
94
Rep
349
Posts

Drives: 2014 CP M5 / 2016 SRT Jeep
Join Date: Aug 2013
Location: Phoenix, AZ

iTrader: (2)

oh wow, wish I would have known about that tool before!

For anyone interested, the part number for those red triangular hangers for the axle back portion of the exhaust is 18207544809. They were $25 a piece from my local BMW dealer. New one is on and exhaust is perfect now
__________________
14 Space Grey CP M5 / CCB / Exec / etc
BMS Stage 1 / Charcoal Delete / K&Ns / Catless OEM DP & Borla S-Type Catback
Appreciate 0
      04-09-2014, 12:15 PM   #35
FormulaMMM
Brigadier General
FormulaMMM's Avatar
United_States
3665
Rep
3,422
Posts

Drives: E90 M3
Join Date: Oct 2011
Location: Midwest

iTrader: (2)

4 years later, still a useful DIY.

A few notes to add based upon my first DIY stock muffler removal yesterday –

Yes, you can fit a shallow ratchet + 18 mm socket to get these.



It’s useful to have a small flathead to lift/pry the clips off of the bolts once you remove those 18 mm nuts as well. Mine were pretty snug.

The rear hanger is indeed held up by E10 reverse torx bolts. Suggest getting that specific socket (cost me $2.99).

10” extender is perfect.

I didn’t go the jack route. Instead, put some padding up at the front of the muffler, grabbed it by the tips (that’s, tips), and jostled a bit. Front section dropped down onto padding and then I lowered the muffler down slowly with man power. When I removed all of the bolts, nuts, etc. it acted like it wasn’t going anywhere. The rear side hangers with the long bolts were holding it in place quite well, actually. So I think it’s optimistic to support it with the jack, remove everything, then simply lower the jack. Not saying going that route is wrong, or won’t work, but I would have found the jack to be more in the way than anything. Maybe others have removed everything and it dropped like a rock, in which case a jack would be nice.

56” race ramps worked well. A bit more clearance at the front end of the muffler would have been nice, but no real complaints. Didn’t impede.

Hit everything with Liquid Wrench the night before, and everything came off without issue.

Whole process took about 1 hour and I’m a mechanical idiot.

Car sans mufflers is absurdly loud, especially on cold start. My DCT is in a storage unit currently and I thought it was going to collapse.
__________________
M4 GTS, GT3, C63 S | E90 M3s, E39 M5

Appreciate 0
      04-18-2014, 03:32 PM   #36
r1762
Second Lieutenant
r1762's Avatar
40
Rep
292
Posts

Drives: 2010 E90 M3
Join Date: Mar 2013
Location: Kaiserslautern, Germany

iTrader: (4)

Thanks for the write up just did my exhaust last week!
Appreciate 0
      05-25-2014, 07:32 PM   #37
MTM
Lieutenant
85
Rep
466
Posts

Drives: 2009 M3
Join Date: Sep 2011
Location: Houston

iTrader: (1)

So glad this DIY is here. I just finished the job and am quite happy with how easy it was. The only strange thing is I never encountered the E10 reverse torx bolt...
Appreciate 0
      06-15-2014, 11:01 PM   #38
sadiq
Enlisted Member
3
Rep
40
Posts

Drives: 2008 E90 M3, 2007 A-M Vantage
Join Date: Aug 2013
Location: Fairfax, VA

iTrader: (0)

This DIY was a life saver. Just want to add one detail to the "It's easier to just remove all of the hangars from the car, rather than muscle the red poly bushings off of the catback while lying on your back" step. Removing those bushings is REALLY hard... unless you have WD40 (or the right tool, mentioned above). I tried for a good 30-40 minutes to get it off with leverage, bare hands, and several flat head screw drivers (like an idiot). A couple of sprays of WD40 and all the bushings pulled off with only moderate bare hand effort.

While the above posts also reference an E10 reverse torx socket, I never felt the need, as the standard (5/16", i think) socket hooked in with no problems.
Appreciate 0
      06-16-2014, 08:00 AM   #39
C-ARchitect
Banned
282
Rep
473
Posts

Drives: Miniature Ferrari
Join Date: May 2014
Location: DC/MD/VA/PA

iTrader: (0)

Just an FYI for anyone attempting this, 2010+ models used E10 reverse torx for the rear hangers. 2008-2009 use standard nut.
Appreciate 0
      06-16-2014, 08:51 PM   #40
FormulaMMM
Brigadier General
FormulaMMM's Avatar
United_States
3665
Rep
3,422
Posts

Drives: E90 M3
Join Date: Oct 2011
Location: Midwest

iTrader: (2)

Quote:
Originally Posted by C-ARchitect View Post
Just an FYI for anyone attempting this, 2010+ models used E10 reverse torx for the rear hangers. 2008-2009 use standard nut.
E10 for me on both my '08 and '09.
__________________
M4 GTS, GT3, C63 S | E90 M3s, E39 M5

Appreciate 0
      06-16-2014, 10:44 PM   #41
C-ARchitect
Banned
282
Rep
473
Posts

Drives: Miniature Ferrari
Join Date: May 2014
Location: DC/MD/VA/PA

iTrader: (0)

Quote:
Originally Posted by FormulaMMM View Post
E10 for me on both my '08 and '09.
I stand corrected, perhaps E10 reverse torx has been an E90 thing from the start.
Appreciate 0
      06-17-2014, 07:06 AM   #42
FormulaMMM
Brigadier General
FormulaMMM's Avatar
United_States
3665
Rep
3,422
Posts

Drives: E90 M3
Join Date: Oct 2011
Location: Midwest

iTrader: (2)

Quote:
Originally Posted by C-ARchitect View Post
I stand corrected, perhaps E10 reverse torx has been an E90 thing from the start.
No problem. If M engineers were a courteous crew, it would have been a standard nut, but they enjoy torturing DIY'ers.
__________________
M4 GTS, GT3, C63 S | E90 M3s, E39 M5

Appreciate 0
      06-17-2014, 10:09 PM   #43
Petros
Banned
65
Rep
1,381
Posts

Drives: M3
Join Date: Jan 2014
Location: Canada

iTrader: (1)

Quote:
Originally Posted by FormulaMMM View Post
No problem. If M engineers were a courteous crew, it would have been a standard nut, but they enjoy torturing DIY'ers.


I agree. This car seems to be specifically designed to be a serious PITA for anyone who tries to work on it themselves. I've owned and worked on several cars in the past, and this is the least fun to work on by a great margin.
Appreciate 0
      06-30-2014, 01:06 AM   #44
Musker18
New Member
0
Rep
25
Posts

Drives: 2008 e92
Join Date: Jun 2014
Location: United States

iTrader: (0)

This helped me a bunch. Thank you!
Appreciate 0
Post Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 06:31 PM.




m3post
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST