|
|
12-08-2012, 02:09 PM | #1 |
-
11809
Rep 23,186
Posts |
wanted DIY OEM rotor removal
looks like a pretty easy job as i change pads all the time. just wondering if there is a DIY for rotor replacement or any tricks i needed to know. Have Turner stud kit so will have to pull those and replace into new hat. thanks
__________________
02 Tiag e46 M3|6MT|GC plates|MCS c.o.|GC bars|GC race control arms|GC bushings|BW eng. & tran. mounts|subframe kit|BW race shifter|BW Jaffster|Euro header|BW exhaust|K&N c.a.i.|Epic race tune|Rouge pulleys|Seibon CF hood|CSL bumper|apr gt 250 & splitter|ST-40|XR-2|SS lines|half cage|Recaro profi|Profi 2 harness|BMWpedals|BW studs| |
12-09-2012, 08:24 PM | #2 |
Lieutenant Colonel
746
Rep 1,848
Posts |
There aren't any real tricks, but I'd recommend a couple of things:
- remove the set screws before you remove the calipers otherwise you won't have anything to stop the rotors from turning when you try to remove these screws. - make sure to disengage parking brake when actually removing the rear rotors |
Appreciate
0
|
12-09-2012, 08:36 PM | #3 |
-
11809
Rep 23,186
Posts |
okay thanks. those are both good tips.
__________________
02 Tiag e46 M3|6MT|GC plates|MCS c.o.|GC bars|GC race control arms|GC bushings|BW eng. & tran. mounts|subframe kit|BW race shifter|BW Jaffster|Euro header|BW exhaust|K&N c.a.i.|Epic race tune|Rouge pulleys|Seibon CF hood|CSL bumper|apr gt 250 & splitter|ST-40|XR-2|SS lines|half cage|Recaro profi|Profi 2 harness|BMWpedals|BW studs| |
Appreciate
0
|
12-17-2012, 10:04 PM | #4 |
-
11809
Rep 23,186
Posts |
anyone find one i still havent.
__________________
02 Tiag e46 M3|6MT|GC plates|MCS c.o.|GC bars|GC race control arms|GC bushings|BW eng. & tran. mounts|subframe kit|BW race shifter|BW Jaffster|Euro header|BW exhaust|K&N c.a.i.|Epic race tune|Rouge pulleys|Seibon CF hood|CSL bumper|apr gt 250 & splitter|ST-40|XR-2|SS lines|half cage|Recaro profi|Profi 2 harness|BMWpedals|BW studs| |
Appreciate
0
|
12-18-2012, 09:55 AM | #7 |
-
11809
Rep 23,186
Posts |
I'm also wondering about wheel bearings. My guess is that removal of the rotor gives easy access for their replacement. Not sure if I need it yet at 27K but there have track miles
__________________
02 Tiag e46 M3|6MT|GC plates|MCS c.o.|GC bars|GC race control arms|GC bushings|BW eng. & tran. mounts|subframe kit|BW race shifter|BW Jaffster|Euro header|BW exhaust|K&N c.a.i.|Epic race tune|Rouge pulleys|Seibon CF hood|CSL bumper|apr gt 250 & splitter|ST-40|XR-2|SS lines|half cage|Recaro profi|Profi 2 harness|BMWpedals|BW studs| |
Appreciate
0
|
01-17-2013, 10:11 PM | #8 |
Captain
314
Rep 755
Posts |
The removal of the rotor is pretty easy once you have the caliber off. Just put some wd40 into the center if the rotor is stuck, then just use a mallet to hit the rotor from behind as you rotate the rotor, and it should come off. It's pretty straight forward. Hope this helps.
__________________
G20 with some ///M3 stuff = G80
|
Appreciate
0
|
01-17-2013, 10:19 PM | #9 | |
-
11809
Rep 23,186
Posts |
Quote:
__________________
02 Tiag e46 M3|6MT|GC plates|MCS c.o.|GC bars|GC race control arms|GC bushings|BW eng. & tran. mounts|subframe kit|BW race shifter|BW Jaffster|Euro header|BW exhaust|K&N c.a.i.|Epic race tune|Rouge pulleys|Seibon CF hood|CSL bumper|apr gt 250 & splitter|ST-40|XR-2|SS lines|half cage|Recaro profi|Profi 2 harness|BMWpedals|BW studs| |
|
Appreciate
0
|
01-18-2013, 08:45 AM | #11 |
BimmerPost Supporting Vendor
311
Rep 13,058
Posts
Drives: BPMsport 2012 E92 M3
Join Date: Jun 2011
Location: Kansas
iTrader: (45)
Garage List 2013 Nissan GTR [0.00]
2019 Sierra Denali ... [0.00] 1999 Nissan Silvia [0.00] 1999 Nissan Skyline ... [0.00] 1998 Toyota Supra [0.00] |
Removal of front and rear are straightforward. You may need to use a hammer with the screwdriver to remove the set screw depending on how old your brakes are. Also, the rotors may be hard to remove due to rust. A good plastic mallet will help here. Otherwise, removal is the same as any other car.
|
Appreciate
0
|
01-18-2013, 09:34 AM | #12 |
-
11809
Rep 23,186
Posts |
Went to change them out last night but still have 28.5 to 28.7 left so gonna wait a few more track days and change em out in the spring.
__________________
02 Tiag e46 M3|6MT|GC plates|MCS c.o.|GC bars|GC race control arms|GC bushings|BW eng. & tran. mounts|subframe kit|BW race shifter|BW Jaffster|Euro header|BW exhaust|K&N c.a.i.|Epic race tune|Rouge pulleys|Seibon CF hood|CSL bumper|apr gt 250 & splitter|ST-40|XR-2|SS lines|half cage|Recaro profi|Profi 2 harness|BMWpedals|BW studs| |
Appreciate
0
|
02-13-2013, 07:01 AM | #13 |
Captain
68
Rep 869
Posts |
What is the minimal rotor thickness before needing to replace? (StopTechs)
__________________
2008 M3 Coupe / DCT // StopTech BBK 380/355 / Pagid RS29 / Motul / Apex Arc-8 / BFG R1S / Ground Control / MS filter / Performance spoiler / BPM tune // Road Atlanta 1:39.70 / VIR Full 2:10.87 / Barber 1:42.20 |
Appreciate
0
|
02-17-2013, 09:08 AM | #14 |
Lieutenant Colonel
746
Rep 1,848
Posts |
|
Appreciate
0
|
02-18-2013, 09:22 AM | #15 | |
-
11809
Rep 23,186
Posts |
Quote:
__________________
02 Tiag e46 M3|6MT|GC plates|MCS c.o.|GC bars|GC race control arms|GC bushings|BW eng. & tran. mounts|subframe kit|BW race shifter|BW Jaffster|Euro header|BW exhaust|K&N c.a.i.|Epic race tune|Rouge pulleys|Seibon CF hood|CSL bumper|apr gt 250 & splitter|ST-40|XR-2|SS lines|half cage|Recaro profi|Profi 2 harness|BMWpedals|BW studs| |
|
Appreciate
0
|
02-18-2013, 01:21 PM | #16 |
Captain
71
Rep 954
Posts |
I think this was more-so directed at removing the rotor. Sometimes they get stuck on and you need to pry them off with a screw driver or 'motivate' them with some shots from a deadblow hammer. When trying to get the rotor loose stand clear as best you can because you don't want the rotor landing in your foot.
|
Appreciate
0
|
02-18-2013, 01:54 PM | #17 | |
-
11809
Rep 23,186
Posts |
Quote:
__________________
02 Tiag e46 M3|6MT|GC plates|MCS c.o.|GC bars|GC race control arms|GC bushings|BW eng. & tran. mounts|subframe kit|BW race shifter|BW Jaffster|Euro header|BW exhaust|K&N c.a.i.|Epic race tune|Rouge pulleys|Seibon CF hood|CSL bumper|apr gt 250 & splitter|ST-40|XR-2|SS lines|half cage|Recaro profi|Profi 2 harness|BMWpedals|BW studs| |
|
Appreciate
0
|
02-18-2013, 02:25 PM | #18 |
Captain
105
Rep 893
Posts |
no, the screws are there only to hold the rotor onto the hub. Thats it. On cars with studs or BMWs with the stud conversion, they arent *really* needed since the wheel keeps it pressed against the hub like any other car on the road.
|
Appreciate
0
|
02-18-2013, 03:48 PM | #19 |
-
11809
Rep 23,186
Posts |
Okay got it. So the set screws are just that. Locate the hat on the mounting plate. Then the wheel torque holds the assembly on to that backing plate.
__________________
02 Tiag e46 M3|6MT|GC plates|MCS c.o.|GC bars|GC race control arms|GC bushings|BW eng. & tran. mounts|subframe kit|BW race shifter|BW Jaffster|Euro header|BW exhaust|K&N c.a.i.|Epic race tune|Rouge pulleys|Seibon CF hood|CSL bumper|apr gt 250 & splitter|ST-40|XR-2|SS lines|half cage|Recaro profi|Profi 2 harness|BMWpedals|BW studs| |
Appreciate
0
|
02-18-2013, 04:42 PM | #20 |
Colonel
60
Rep 2,185
Posts |
Please don't be like me and forget to release the hand brake when trying to remove the rear rotors.
__________________
Vf supercharger + tune/H&R coils/ Akra evolution exhaust/Volk te37/ Rs-3 tires/ Brembos /TIal BOV/ OSS blacked out headlights/LUX v3/Led taillights/ Challenge Front lip/ P3 vent gauge/ F10 m5 shift mob/Matte black front grills/ And a funky air fresher
|
Appreciate
0
|
02-18-2013, 05:26 PM | #21 |
-
11809
Rep 23,186
Posts |
Thanks already got that tip and only doing the fronts this time.
__________________
02 Tiag e46 M3|6MT|GC plates|MCS c.o.|GC bars|GC race control arms|GC bushings|BW eng. & tran. mounts|subframe kit|BW race shifter|BW Jaffster|Euro header|BW exhaust|K&N c.a.i.|Epic race tune|Rouge pulleys|Seibon CF hood|CSL bumper|apr gt 250 & splitter|ST-40|XR-2|SS lines|half cage|Recaro profi|Profi 2 harness|BMWpedals|BW studs| |
Appreciate
0
|
02-19-2013, 12:20 AM | #22 |
-
11809
Rep 23,186
Posts |
just did this tonight. barely takes any more time than pads do. super easy. my set screws were easily removed and the rotor just fell off no need to beat it first with a hammer. it took longer to double nut my studs as i was replacing my turners for new set of apex at the same time.
__________________
02 Tiag e46 M3|6MT|GC plates|MCS c.o.|GC bars|GC race control arms|GC bushings|BW eng. & tran. mounts|subframe kit|BW race shifter|BW Jaffster|Euro header|BW exhaust|K&N c.a.i.|Epic race tune|Rouge pulleys|Seibon CF hood|CSL bumper|apr gt 250 & splitter|ST-40|XR-2|SS lines|half cage|Recaro profi|Profi 2 harness|BMWpedals|BW studs| |
Appreciate
0
|
Post Reply |
Bookmarks |
|
|