|
|
|
|
|
Thread Tools | Search this Thread |
09-16-2012, 09:55 PM | #89 |
Lieutenant General
2416
Rep 13,090
Posts |
Because these PDX can be stacked what I did was just a plastic platform held by velcro to the OEM amp frame on one side and to the metal frame at the other end. The PDXs are just placed on top of the platform also with velcro.
Velcro allows moving the platform -and thus the PDX- for positioning and to access the wires/cables without any permanent changes/modifications. |
Appreciate
0
|
09-17-2012, 08:01 AM | #90 | |
BimmerPost Supporting Vendor
311
Rep 13,058
Posts
Drives: BPMsport 2012 E92 M3
Join Date: Jun 2011
Location: Kansas
iTrader: (45)
Garage List 2013 Nissan GTR [0.00]
2019 Sierra Denali ... [0.00] 1999 Nissan Silvia [0.00] 1999 Nissan Skyline ... [0.00] 1998 Toyota Supra [0.00] |
Quote:
|
|
Appreciate
0
|
09-27-2012, 11:59 AM | #91 |
New Member
0
Rep 7
Posts |
I'm needing to try and grab a harness, but can't pm yet. going in a 2008 335 with hifi sound system. I'm only wanting to keep the stock head unit and will be using an Audison Bit 10, 2 Arc mini 125.4 amps, Hybrid L4v2 SE Carbon and L1V2 NH tweeters run active and shallow mount Hertz drivers under the seat till Hybrid comes out with their option. can you shoot me an a-mail at Chad@BosworthAudio.com?
|
Appreciate
0
|
09-27-2012, 12:23 PM | #92 | |
Lieutenant General
2416
Rep 13,090
Posts |
Quote:
I do have the Logic7 harness available however it is not to replace the OEM amp. The harness is used to interface with the OEM amp outputs and speaker inputs. |
|
Appreciate
0
|
09-27-2012, 08:22 PM | #93 |
Brigadier General
300
Rep 3,969
Posts |
Sure about the L1V2 together with the carbons?
__________________
Mobridge DA2 > JBL MS-8 > ARC XDi 600/4 > JBL Gti 408 Mids & Vifa OT19 Tweeters; PG Ti2 1600.5 > Morel HCW-10 & IDMax 15
|
Appreciate
0
|
09-28-2012, 10:58 AM | #94 |
New Member
0
Rep 7
Posts |
I'm looking to replace it all together, but if my only option is to keep the amp, and use it's outputs summed together in the Audison processor and run back out to the Arc amplifiers then that is how i have to do it for now.
|
Appreciate
0
|
09-28-2012, 12:13 PM | #96 | |
Lieutenant General
2416
Rep 13,090
Posts |
Quote:
Wiring the OEM amp outputs to the bit Ten should work, although the woofer outputs max levels are too close to the bit Ten max input level. |
|
Appreciate
0
|
09-28-2012, 06:21 PM | #98 | ||
Lieutenant General
2416
Rep 13,090
Posts |
Quote:
Quote:
|
||
Appreciate
0
|
10-02-2012, 03:49 PM | #100 |
Lieutenant General
2416
Rep 13,090
Posts |
|
Appreciate
0
|
10-02-2012, 04:49 PM | #101 |
New Member
0
Rep 7
Posts |
|
Appreciate
0
|
10-02-2012, 04:58 PM | #102 |
Lieutenant General
2416
Rep 13,090
Posts |
|
Appreciate
0
|
10-02-2012, 05:21 PM | #103 |
New Member
0
Rep 7
Posts |
|
Appreciate
0
|
10-03-2012, 04:30 AM | #104 |
Lieutenant General
2416
Rep 13,090
Posts |
|
Appreciate
0
|
10-04-2012, 10:03 AM | #105 |
Lieutenant
52
Rep 544
Posts |
Quick dummy question on the install. How do you remove the housing for the speakers in the doors as I'm about to do the same? Do they just pop off do do you have to remove the whole door panel. Been a LONG time since i've done a stereo install.
|
Appreciate
0
|
10-04-2012, 06:02 PM | #106 |
Lieutenant General
2416
Rep 13,090
Posts |
You need to remove the door panels.
|
Appreciate
0
|
02-18-2013, 08:16 PM | #107 |
New Member
0
Rep 7
Posts |
This is the EXACT system I would like to do, I've just purchased a 2008 with EPS. I've got the EPS system, so I need to code to HIFI and use your harness to go to MS8 and then aftermarket amp, do I have it correct?
Thanks, Justin Wade |
Appreciate
0
|
02-19-2013, 08:36 AM | #108 | |
Lieutenant General
2416
Rep 13,090
Posts |
Quote:
|
|
Appreciate
0
|
08-11-2013, 04:54 PM | #109 |
Registered
0
Rep 4
Posts |
HELP!!
Right....
All this ohms, amps, eps and numbers is confusing me... could someone please help/tell me what would be the best, least destructive way of me getting a louder deeper bass (for example... would i get away with just upgrading the under seat sub/speakers?) I would also like to replace all standard speakers to upgraded ones whilst keeping to oem connections and harnesses? Is this possible? or does anyone know of the right size speakers so its a direct replacement? Thanks, Tom |
Appreciate
0
|
08-11-2013, 05:13 PM | #110 | |
Lieutenant General
2416
Rep 13,090
Posts |
You need to open your own thread, please. And do a lot of searching if you are confused.
Quote:
|
|
Appreciate
0
|
Bookmarks |
|
|