BMW M3 Forum (E90 E92)

BMW Garage BMW Meets Register Search Today's Posts Mark Forums Read


Go Back   M3Post - BMW M3 Forum > M3 (E90 / E92 / E93) > General M3 Forum (E90 + E92 + E93)
 
GTB Performance
Post Reply
 
Thread Tools Search this Thread
      12-12-2012, 06:25 PM   #1
AshyLarryMP
Lieutenant
United_States
9
Rep
422
Posts

 
Drives: 2011 MW E92 ZCP DCT
Join Date: Nov 2012
Location: San Diego

iTrader: (0)

New software update 12/7/12

A new software update came out less than a week ago. My 2011 zcp dct was running 2010 software. The dealer said I was running E89X-10-09-511. Now I am running E89X-12-07-508. The new build is also referred to as 2.48.2.

The bucking problem in 1st gear is now gone.

It cost me $150 because the update wasn't done to fix a specific problem. I just wanted to have it done. However, I bet I could have gotten them to pay for it if I told them my car was bucking.

If you are running very old software you need to have it upgraded. Don't spend too much time thinking about it, just do it. I'm actually a little pissed off that the car didn't run like this when I bought it.
Appreciate 0
      12-12-2012, 06:30 PM   #2
Transfer
Lieutenant Colonel
Transfer's Avatar
United_States
24
Rep
1,689
Posts

 
Drives: SQ5, X1
Join Date: Mar 2010
Location: Seattle, WA

iTrader: (0)

booya. I'll be trying to get this done on my 2011 ZCP right after the new year. Any perceived power changes?
Appreciate 0
      12-12-2012, 06:39 PM   #3
M3PO
Colonel
M3PO's Avatar
34
Rep
2,777
Posts

 
Drives: '08 IB E92
Join Date: Sep 2011
Location: OC

iTrader: (7)

The "12-07" suggests that the software is from july '12 I think, which would be 240E.
__________________
2008 IB E92 M3| BBS | KW | Arkym | Platte Forme A.G. | Active Autowerke | K&N | Fabspeed | Dinan | Evolve-R
Appreciate 0
      12-12-2012, 06:50 PM   #4
AshyLarryMP
Lieutenant
United_States
9
Rep
422
Posts

 
Drives: 2011 MW E92 ZCP DCT
Join Date: Nov 2012
Location: San Diego

iTrader: (0)

The dealer said the new update just came out on Sunday. I think the 12.07 part of 12.07.508 indicates the update was made on December 7th.

My car was delivered on 1/28/11 and the program I was running was 10.09.511. I'm guessing the old program was from October 9th 2010.

I don't think you need an update unless you are running 2010 software.

I can't feel the 10 or 20 horsepower gain that some claim. A small hp gain would be hard to notice in a car like this. The change in drive-ability is drastically better and that is what you will notice.

However, I do believe that the car does have more horsepower. The BMW tuners have had more time to update their programs and make them better.

Last edited by AshyLarryMP; 12-12-2012 at 07:02 PM.
Appreciate 0
      12-12-2012, 07:03 PM   #5
anacondatp
Private First Class
3
Rep
170
Posts

 
Drives: 10' E92 M3 6MT
Join Date: Mar 2012
Location: SoCal

iTrader: (2)

mine is 6MT, how do I get the dealer to do a free upgrade?
__________________
10' E92 M3 6MT
Appreciate 0
      12-12-2012, 07:14 PM   #6
808@702
7th BMW, 500th Surfboard
808@702's Avatar
68
Rep
1,075
Posts

 
Drives: My girlfriends crazy!
Join Date: Sep 2009
Location: Las Vegas, Nv. and Honolulu, Hi.

iTrader: (0)

Quote:
Originally Posted by anacondatp View Post
mine is 6MT, how do I get the dealer to do a free upgrade?
+1000
Appreciate 0
      12-12-2012, 09:14 PM   #7
Jremmy
Medic
Jremmy's Avatar
3
Rep
222
Posts

 
Drives: 2013 M3
Join Date: Oct 2012
Location: San Diego, CA

iTrader: (0)

Quote:
Originally Posted by AshyLarryMP View Post
A new software update came out less than a week ago. My 2011 zcp dct was running 2010 software. The dealer said I was running E89X-10-09-511. Now I am running E89X-12-07-508. The new build is also referred to as 2.48.2.

The bucking problem in 1st gear is now gone.

It cost me $150 because the update wasn't done to fix a specific problem. I just wanted to have it done. However, I bet I could have gotten them to pay for it if I told them my car was bucking.

If you are running very old software you need to have it upgraded. Don't spend too much time thinking about it, just do it. I'm actually a little pissed off that the car didn't run like this when I bought it.
what dealer in SD did you take it to? I've been going to South County for service solely due to horror stories I've heard from friends w/ E92s that took their cars to Vista and Encinitas...
Appreciate 0
      12-12-2012, 09:36 PM   #8
AshyLarryMP
Lieutenant
United_States
9
Rep
422
Posts

 
Drives: 2011 MW E92 ZCP DCT
Join Date: Nov 2012
Location: San Diego

iTrader: (0)

I go to BMW of San Diego which is on Kearny Mesa Road. I'm new to BMW and have only been there 2 times. They did a great job repairing and working on my car each time. Highly recommended.
Appreciate 0
      12-12-2012, 09:56 PM   #9
W Cole
Captain
14
Rep
779
Posts

 
Drives: 2009 M3
Join Date: Dec 2010
Location: Newport Coast, CA

iTrader: (5)

Quote:
Originally Posted by AshyLarryMP View Post
A new software update came out less than a week ago. My 2011 zcp dct was running 2010 software. The dealer said I was running E89X-10-09-511. Now I am running E89X-12-07-508. The new build is also referred to as 2.48.2.

The bucking problem in 1st gear is now gone.

It cost me $150 because the update wasn't done to fix a specific problem. I just wanted to have it done. However, I bet I could have gotten them to pay for it if I told them my car was bucking.

If you are running very old software you need to have it upgraded. Don't spend too much time thinking about it, just do it. I'm actually a little pissed off that the car didn't run like this when I bought it.
Wow, $150 to upgrade everything seems very reasonable. I hear stories of dealers asking $100s and saying the customer is responsible if the dealer burns out any modules in the process.
Appreciate 0
      12-12-2012, 10:20 PM   #10
Jremmy
Medic
Jremmy's Avatar
3
Rep
222
Posts

 
Drives: 2013 M3
Join Date: Oct 2012
Location: San Diego, CA

iTrader: (0)

Quote:
Originally Posted by AshyLarryMP View Post
I go to BMW of San Diego which is on Kearny Mesa Road. I'm new to BMW and have only been there 2 times. They did a great job repairing and working on my car each time. Highly recommended.
Thanks! Good to know.
Appreciate 0
      12-12-2012, 10:45 PM   #11
Munit
Banned
8
Rep
220
Posts

 
Drives: m3
Join Date: Oct 2012
Location: CA

iTrader: (0)

Is there any service bulletin for the bucking so we can take it in and state the SB to get the upgrade? I am under full warranty
Appreciate 0
      12-13-2012, 09:25 AM   #12
LIQUIX
Private
1
Rep
75
Posts

 
Drives: E92 M3
Join Date: Apr 2005
Location: Orlando

iTrader: (0)

Quote:
Originally Posted by Munit View Post
Is there any service bulletin for the bucking so we can take it in and state the SB to get the upgrade? I am under full warranty
Would love to know if it fixes the bucking on 6MT as well.
Appreciate 0
      12-13-2012, 10:37 AM   #13
kawasaki00
Major
kawasaki00's Avatar
17
Rep
1,232
Posts

 
Drives: E92
Join Date: May 2012
Location: Charlotte NC

iTrader: (4)

E89X-10-09-511
That is September 2010, there is no day in the numbering
12-07-508
This is July 2012 just as M3PO Stated, it has been out a while, your dealer was pulling your chain talking about it just come out.
__________________
Electronics Junkie, Engine Builder.
Appreciate 0
      12-13-2012, 10:41 AM   #14
jphughan
Brigadier General
jphughan's Avatar
United_States
39
Rep
3,465
Posts

 
Drives: 2011.75 M3 E92 6MT
Join Date: Mar 2011
Location: Austin, TX

iTrader: (0)

Quote:
Originally Posted by LIQUIX View Post
Would love to know if it fixes the bucking on 6MT as well.
Same. Evidently there are aftermarket engine tunes that remove it for 6MT, which suggests it's a DME change, not a transmission software change, in which case the update may well remove the bucking for 6MT. Although even if it does, getting a free software update would probably require BMW to put out a service bulletin about the bucking and indicate that new software fixes the issue. I'm not too worried about it though given that it only happens for me when the engine is stone cold and at very low speeds.
__________________
11 M3 E92 Le Mans | Black Nov w/ Alum | 6MT | Premium 2 | Convenience | 19" | EDC | Prem Audio | Moonroof | BMW Apps | Yoko AD08 R | Vorshlag Adjustable Camber Plates | StopTech ST-60 380mm BBK | Castrol SRF Fluid | ModMyNav.com rear camera | OEM Euro Sunglasses Holder
Appreciate 0
      12-13-2012, 11:18 AM   #15
W///
Major General
W///'s Avatar
82
Rep
5,394
Posts

 
Drives: 2008 E92 M3/1999 E36 M3 Coupe
Join Date: Sep 2011
Location: SC

iTrader: (12)

Quote:
Originally Posted by jphughan View Post
Same. Evidently there are aftermarket engine tunes that remove it for 6MT, which suggests it's a DME change, not a transmission software change, in which case the update may well remove the bucking for 6MT. Although even if it does, getting a free software update would probably require BMW to put out a service bulletin about the bucking and indicate that new software fixes the issue. I'm not too worried about it though given that it only happens for me when the engine is stone cold and at very low speeds.
Ok wasn't sure what you guys were talking about, but I get the bucking too. As long as you wait for cold start to end (aka around 15 seconds after starting the car), the issue isn't there.
__________________
2008 E92 M3: Sparkling Graphite | Bamboo Beige | 6MT | CF Roof | HRE | Catless Eisenmann Race | BPM Sport | Swift | Arkym | Mode Carbon | M.Perf
Appreciate 0
      12-13-2012, 11:43 AM   #16
ChrisK
Brigadier General
ChrisK's Avatar
United_States
86
Rep
4,865
Posts

 
Drives: E92 M3
Join Date: Jun 2007
Location: IL

iTrader: (4)

I have been running E89X-12-03-502 for awhile now, which is 2.48. I wonder if I should update?

The bucking was almost gone after this update.
__________________

2011 E92 M3: AW/BLK • DCT
Europäische Lieferung am 6. August 2010
Appreciate 0
      12-13-2012, 12:50 PM   #17
DBH
First Lieutenant
3
Rep
349
Posts

 
Drives: 2011 M3 E92
Join Date: Jan 2011
Location: SE PA

iTrader: (0)

Quote:
Originally Posted by jphughan View Post
Same. Evidently there are aftermarket engine tunes that remove it for 6MT, which suggests it's a DME change, not a transmission software change, in which case the update may well remove the bucking for 6MT. Although even if it does, getting a free software update would probably require BMW to put out a service bulletin about the bucking and indicate that new software fixes the issue. I'm not too worried about it though given that it only happens for me when the engine is stone cold and at very low speeds.
Not quite sure what you're talking about. The bucking on my MT is only at very low speeds and can be eliminated by pushing in the clutch pedal and than engaging again. This has happened to every MT car I'll ever owned and is due to normal drivetrain loseness.
Appreciate 0
      12-13-2012, 05:40 PM   #18
Rapture
I'm suckin gas but I'm haulin ass
Rapture's Avatar
United_States
12
Rep
656
Posts

 
Drives: 2011 MR E92 M3
Join Date: Sep 2010
Location: OC, CA

iTrader: (13)

I just had my 2011 DCT updated from 200E to 240E by EAS. From my understanding that is 5 updates behind. The car "bucks" less (even though it rarely happened before). The biggest improvement is cold start driving and the DCT seems to be sharper and quicker.
I should note EAS charges less than $150 to do the update and you can wait while it's done.
Appreciate 0
      12-13-2012, 07:49 PM   #19
cambit
Private First Class
United_States
1
Rep
150
Posts

 
Drives: 2013 BMW M3 COUPE
Join Date: Jul 2012
Location: San Francisco, CA

iTrader: (0)

when I fill up with 100 octane racing fuel, the bucking you describe on cold starts completely goes away. try it and report back your results.
Appreciate 0
      12-13-2012, 08:57 PM   #20
eisenb11
Major
United_States
17
Rep
1,122
Posts

 
Drives: 2012 E92 M3 SSII
Join Date: Oct 2007
Location: Redondo Beach, CA, USA

iTrader: (0)

Quote:
Originally Posted by AshyLarryMP View Post
The bucking problem in 1st gear is now gone.
To be clear, which bucking problem are we talking about?
  1. The herking and jerking when driving around very very slowly in 1st gear
  2. The one that can happen when your stopped then accellerate really hard
  3. The one that people are talking about during the cold-start period
Appreciate 0
      12-13-2012, 09:08 PM   #21
gedwierico
New Member
0
Rep
7
Posts

 
Drives: audi
Join Date: Dec 2012
Location: men

iTrader: (0)

I don't think you need an update unless you are running 2010 software.
__________________
Appreciate 0
      12-13-2012, 09:23 PM   #22
AshyLarryMP
Lieutenant
United_States
9
Rep
422
Posts

 
Drives: 2011 MW E92 ZCP DCT
Join Date: Nov 2012
Location: San Diego

iTrader: (0)

Quote:
Originally Posted by eisenb11 View Post
To be clear, which bucking problem are we talking about?
[*]The one that people are talking about during the cold-start period[/list]
This one best describes it.
Appreciate 0
Post Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 09:51 PM.




m3post
Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST