BMW M3 Forum (E90 E92)

BMW Garage BMW Meets Register Search Today's Posts Mark Forums Read


Go Back   M3Post - BMW M3 Forum > E90/E92 M3 Technical Topics > Track / Autocross / Dragstrip / Driving Techniques
 
Steve Thomas BMW
Post Reply
 
Thread Tools Search this Thread
      09-22-2012, 02:42 PM   #1
Shosholoza
Shosholoza
Shosholoza's Avatar
United_States
10
Rep
188
Posts

Drives: E92 M3
Join Date: Jul 2011
Location: Melbourne, Florida

iTrader: (1)

E92 - Schroth Quickfit Pro Install

With 370 posts on the other thread, I thought I would add a simple install guide with pics. It took me about 30 minutes.
1. Buy the mini harnesses - HMS were very prompt
2. Tools: Torx T50 socket; torque wrench for 30 ft pounds; a vice with pliers for bending the Schroth brackets

3. Front: Pop the rubber cover off the Torx bolt at the front of the seatbelt rail
4. Undo the T50 bolt
5. Determine how much you want to bend and twist the Schroth bracket. Do it. I tried to get the angle and twist so that it aligned with the direction the belt would pull.
6. Tighten the T50 bolt to 30 ft pounds
7. Trim the rubber boot so that it fits back over the T50 both with the Schroth bracket

8. Rear: Remove the seat cushion - pull up, some effort is required
9. Undo the T50 bolt
10. Determine how much you want to bend and twist the Schroth bracket. Do it. I tried to get the angle and twist so that it aligned with the direction the belt would pull.
11. Tighten the T50 bolt to 30 ft pounds. I did not use the 13mm nut an washers provided by Schroth, because the factory T50 bolt fits just fine
12. Reinstall the seat cushion
Attached Images
     
__________________
SOLD...E92 M3, Competition Package, MDCT, Ground Control Adjustable Camber plates, StopTech 380 BBK, OEM exhaust mod
Appreciate 0
      09-22-2012, 03:10 PM   #2
jml
Captain
jml's Avatar
18
Rep
995
Posts

Drives: E90M3
Join Date: Dec 2008
Location: Austin, TX

iTrader: (2)

Man I'd really prefer it was a crash tested solution in the 3 series like the E46 setup was. I'm not sure PCA will allow that setup BTW. They will not allow 4-point setups, though I did get them to give the E46 coupe quickfit pro an exception because it's DOT approved in that car.

Someone showed up at lonestar PCA last weekend with what look like your setup in an E92, and I didn't call them on it - but technically I should have.
Appreciate 0
      09-03-2013, 02:26 PM   #3
3002 tii
Major General
3002 tii's Avatar
United_States
247
Rep
9,378
Posts

Drives: 07 Z4, 14 X3, 13 135is
Join Date: Apr 2008
Location: Westchester

iTrader: (73)

Garage List
Quote:
Originally Posted by jml View Post
Man I'd really prefer it was a crash tested solution in the 3 series like the E46 setup was. I'm not sure PCA will allow that setup BTW. They will not allow 4-point setups, though I did get them to give the E46 coupe quickfit pro an exception because it's DOT approved in that car.

Someone showed up at lonestar PCA last weekend with what look like your setup in an E92, and I didn't call them on it - but technically I should have.
I know it's an old thread but isn't a 4 pt meant to integrate with the factory system like the Quick Fits "ok" since they have the ASM technology? I thought it was your traditional 4 pt in a bucket seat, with harness/rollbar that was an issue.
__________________

TC Kline | Ground Control | Quaife | Stoptech | Supersprint | Active Autowerke | Volk

Click here for my track videos
Appreciate 0
      09-03-2013, 03:23 PM   #4
surlynkid
Major
surlynkid's Avatar
20
Rep
1,283
Posts

Drives: 2013 E92 M3
Join Date: Apr 2012
Location: League City, TX

iTrader: (1)

Garage List
Directions 3-7 are not the only place to put the stub piece. I placed it under the seat bracket guide using that bolt. That places the belt further forward and more equal in position to the one up against the center console. This is more critical for shorter passengers like my wife that really move the seat forward at the track. She is 5'4"
__________________
Stoptech 380mm/355mm | PFC08 / Pagid RS-29 | Akrapovic EVO - CF tips | Benvo Tune | MS UDP | AA air filter | MCS 2-way with 700/1000lb springs | Solid bushings and adjustable links | RD front swaybar | Apex EC-7 18x10 square 275/35-18 NT01 | Turner Race Studs | GT4 Brake Cooling | GT4 Power Steering Cooling | Alekshop Oil Cooler | Performance Steering Wheel | | CF Spoiler | Varis System 1 Full CF Diffuser | Extended Paddle Shifters | Schroth Quick Fit Pro | Turner Steering Rack Stops | Vorshlag Camber Plates
Appreciate 0
      09-23-2013, 09:27 PM   #5
Splinterz88
Lieutenant
Splinterz88's Avatar
United_States
6
Rep
473
Posts

Drives: BMW 1M
Join Date: Aug 2007
Location: Philadelphia, PA

iTrader: (4)

Garage List
2011 BMW 1M  [4.31]
The belts for e9X have been released now, so no need to use the mini belts anymore.
__________________
#446 of 740
Appreciate 0
Post Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 06:21 AM.




m3post
m3post
Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST