Drill holes on Arkym frnt lip: need advice

werly · 05-16-2011, 01:49 PM

I have just ordered an Arkym CF front lip, which is beautifully crafted and the fitment should be superb according to many opinions on the forum.

Yet the only issue that i run into is that i need to drill holes on the lip before i install bolt it onto the bumper and tape it. And I've heard that using inappropriate drill will crack the lip...so i wonder if i can get some advice on using the right tool and perhaps the proper way to install it.

Thanks for your input

Cal@Sonic MS · 05-16-2011, 01:58 PM

Any power drill with the proper size bit will work fine. There should already be indents on the lip that tell you where to drill the holes.

SIIK2NR · 05-16-2011, 03:15 PM

Lip should have came pre drilled unless you got one of the original versions.

Anyways... USE an Electric Drill with minimum 12 volts. Do NOT use a battery powered drill unless it is 12 volts.

The technique is to use a small bit at high speed at first, then move up gradually through the bit size so the larger bit does not "Grab" the lip and crack it.

Make sure the bit is moving fast as you drill. Don't lift off the trigger while inside the hole... it will grab the hole are rip up the lip.

Use tape to keep the hole and the bit in better control.

Good luck.

1cleanm3 · 05-17-2011, 02:53 AM

If you just ordered it you have nothing to worry about, they come pre drilled.

punksterz626 · 05-17-2011, 10:35 AM

i dont recall mine being predrill. Again,i didnt install it myself. I had LTBMW do it for me. Fitment is spot on.

bigjae1976 · 05-17-2011, 08:37 PM

Drill a pilot hole then use a step bit. That's what I do when I drill through thin mirror plexi...never had a crack. Yet.

werly · 05-19-2011, 01:52 AM

thanks for all your inputs =)

I successfully put holes on the lip few hours ago. The Arkym lip I have does not come pre-drilled but it does not crack under the force of my electrical drill. Now the lip is ready for install! Can't wait to get the car back from bodyshop

05-16-2011, 01:49 PM	#1
werly Second Lieutenant Drives: 2011 MR E92 M3 Join Date: Aug 2010 Location: SoCal Posts: 261 iTrader: (1)	Drill holes on Arkym frnt lip: need advice I have just ordered an Arkym CF front lip, which is beautifully crafted and the fitment should be superb according to many opinions on the forum. Yet the only issue that i run into is that i need to drill holes on the lip before i install bolt it onto the bumper and tape it. And I've heard that using inappropriate drill will crack the lip...so i wonder if i can get some advice on using the right tool and perhaps the proper way to install it. Thanks for your input
	Tweet

05-16-2011, 01:58 PM	#2
Cal@Sonic MS BimmerPost Supporting Vendor Drives: E39 M5 & E28 528e Join Date: Jan 2011 Location: Mountain View, CA Posts: 4,584 iTrader: (2)	Any power drill with the proper size bit will work fine. There should already be indents on the lip that tell you where to drill the holes. __________________ email : cal@sonicms.net \| tel : 650.733.6506 \| aim : calatsms Facebook \| Instagram @sonic_ms \| YouTube

05-16-2011, 03:15 PM	#3
SIIK2NR Captain Drives: AW E92 M3 Join Date: Mar 2007 Location: San Dog Posts: 605 iTrader: (0)	Lip should have came pre drilled unless you got one of the original versions. Anyways... USE an Electric Drill with minimum 12 volts. Do NOT use a battery powered drill unless it is 12 volts. The technique is to use a small bit at high speed at first, then move up gradually through the bit size so the larger bit does not "Grab" the lip and crack it. Make sure the bit is moving fast as you drill. Don't lift off the trigger while inside the hole... it will grab the hole are rip up the lip. Use tape to keep the hole and the bit in better control. Good luck. __________________ Current: 2006 Lotus Elise SC Previous: 2008 AW E92 M3 6MT - Sold 2004 AP2 S2000 - Sold

05-17-2011, 02:53 AM	#4
1cleanm3 Brigadier General Drives: ///E92M3RR SportPrius Join Date: Feb 2008 Location: the 818 Posts: 3,507 iTrader: (7)	If you just ordered it you have nothing to worry about, they come pre drilled. __________________ HRE + CHALLENGE + KW V3 + GINTANI + ARKYM + YOKOHAMA AD08

05-17-2011, 10:35 AM	#5
punksterz626 Major Drives: 08 Alpine White M3 Join Date: Jun 2005 Location: Ahambra Posts: 1,220 iTrader: (8)	i dont recall mine being predrill. Again,i didnt install it myself. I had LTBMW do it for me. Fitment is spot on. __________________ FS or Trade: Brand new CF Hamann Diffuser n Front Lip

05-17-2011, 08:37 PM	#6
bigjae1976 Brigadier General Drives: 04 330Ci, 11 E90 M3 Individual Join Date: Mar 2006 Location: Milwaukee, WI Posts: 4,050 iTrader: (8)	Drill a pilot hole then use a step bit. That's what I do when I drill through thin mirror plexi...never had a crack. Yet. __________________

05-19-2011, 01:52 AM	#7
werly Second Lieutenant Drives: 2011 MR E92 M3 Join Date: Aug 2010 Location: SoCal Posts: 261 iTrader: (1)	thanks for all your inputs =) I successfully put holes on the lip few hours ago. The Arkym lip I have does not come pre-drilled but it does not crack under the force of my electrical drill. Now the lip is ready for install! Can't wait to get the car back from bodyshop

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search