BMW M3 Forum (E90 E92)

BMW Garage BMW Meets Register Search Today's Posts Mark Forums Read


Go Back   M3Post - BMW M3 Forum > M3 Marketplace > SPONSORS Classifieds/Groupbuys/Specials Area > Engine | Drivetrain | Exhaust
 
Closed Thread
 
Thread Tools Search this Thread
      08-26-2010, 03:15 PM   #1
Jason@Renn-Spec
Major
 
Jason@Renn-Spec's Avatar
 
Drives: A POS
Join Date: Jul 2009
Location: La Puente, CA

Posts: 1,312
iTrader: (3)

RENN Spec | Rogue Engineering Octane Short Shifter Kit

Hello m3post members,

We're excited to announce that we just became a Rogue dealer and will be carrying their entire line-up.




After nearly a year of R&D and manufacturing, we are proud to announce our much anticipated OCTANE SSK for the E9X M3. There have been some design challenges along the way, but this is why we diligently pursue the right solutions rather than rushing a kit to market.

As you can see in the picture of the complete kit above, there are specific components that are unique to the E9X M3 OCTANE SSK. By explaining the details of each part, we hope you will comprehend the extent of time and materials that go into each kit.

The Components

A. 6061-T6 ACQ Billet Carrier - Painstakingly CNC machined from a block of aluminum about the size of a brick, this carrier has incredible strength and rigidity over a stock component. It incorporates Rogue Engineering's Pivot Relocation Cup, to raise the pivot point of the shifter higher, allowing the shifter more drivetrain clearance. For additinoal strength, the rear of the carrier has a steel spike to secure to the mounting point of the vehicle. An important feature is that it realigns the selector rod so that it is near the factory position, preventing off-axis forces against the transmission's selector rod gear joint, preventing shifting notchiness. If you wonder why Rogue Engineering's shifters have always been the SMOOTHEST shifters on the market, this is one of many small details which allow many of our customers to recognize the ingenuity of RE OCTANE SSKs. The carrier comes complete with custom Delrin carrier bushings, eliminating excessive carrier movement as a result of the factory rubber bushings.

B. Our OCTANE shifter lever may seem like the same lever we use in our other kits, but at a closer glance, you will see that it incorporates a double bend, to emulate the factory shifter lever. In essence, the top of the factory lever is moved backwards, approximately 1/2 from the axis of the lower part of the shifter. Other companies have made the mistake of only bending the top of another factory lever backwards, hoping to solve this ergonomic challenge. However, bending the top of the lever back only tips the shift knob towards the driver, and does not emulate the factory position accurately. During development, we noticed that the E9X M3 represents the first manual transmission vehicle that BMW has produced where the factory shifter lever is actually excessively lowered. Ergonomics is an important feature in any BMW, and if you were like many of us, we discovered that the shift knob in a stock E9X M3 was very low and very forward (where driver's with larger hands could punch the lower console in the forward gear changes). We deduced that BMW wanted to provide a "sporty" feeling shifter (which it is), but at the expense of driving comfort. With this in mind, we have tweaked the shifter so that it is more comfortable for the driver. Our throws are reduced noticeably, with a 3rd to 4th throw distance of approximately 98mm (3.85") when using the factory shift knob. We maintain our use of the Ertalyte TX pivot point, machined from solid Ertalyte TX rod, to exacting specifications. In developmental testing, our pivot has been shown to be 41% smoother than a stock pivot and an alarming 200% smoother than another aftermarket company's shifter. Small details such as these add up in the long run.

C. Rogue Engineering's Self-Adjusting Pivot Point (SAPP) is still used in our E9X M3 application, proving that our simple and effective method of lower pivot tension control maintains reliability, durability, and longevity. Just ask the 50% of the Grand Am Koni Challenge teams racing with Rogue Engineering shifters in their cars.



D. We replace the hollow, factory selector rod with a heavier, TIG welded, stainless steel replacement. This adds additional mass, over the press-tube construction of the factory part. This helps the shifts in the vehicle feel factory smooth, while allowing for the reduced throws. Our weighted selector rod is twice the mass of the factory part (factory is 120g, ours is 245g).

E. We use factory replacement pivot cups and locking circlips to secure the shifter together. These are the same components used in all current model BMWs.

The current price on the SSK will be $495 shipped anywhere. We are also an Authorize Rogue Installer in the area so please PM me for install quote too!

Last edited by Jason@Renn-Spec; 08-26-2010 at 08:25 PM.
Jason@Renn-Spec is offline  
0
      09-07-2010, 07:10 PM   #2
Simon@RENNSpec
 
Simon@RENNSpec's Avatar
 
Drives: BMW
Join Date: Jul 2007
Location: Los Angeles / Hong Kong

Posts: 981
iTrader: (4)

Send a message via AIM to Simon@RENNSpec Send a message via MSN to Simon@RENNSpec
All inquiries replied!
Simon@RENNSpec is offline   Hong Kong
0
Closed Thread

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 07:08 AM.




m3post
Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST