BMW M3 Forum (E90 E92)

BMW Garage BMW Meets Register Search Today's Posts Mark Forums Read


Go Back   M3Post - BMW M3 Forum > E90/E92 M3 Technical Topics > Engine, Transmission, Exhaust, Drivetrain, ECU Software Modifications
 
GetBMWParts
Post Reply
 
Thread Tools Search this Thread
      05-28-2010, 12:52 PM   #1
mike2010m3
Private
 
mike2010m3's Avatar
 
Drives: 2010 bmw m3
Join Date: Mar 2010
Location: florida

Posts: 66
iTrader: (0)

diy exhaust install help

does any one know where to find a quide to removing your stock exhaust and install a new one... i have tried searching but couldn't find it
__________________
2010 bmw m3 black on black every option.
led angel eyes
mike2010m3 is offline  
0
Reply With Quote
      05-28-2010, 01:02 PM   #2
Trier Germany
Banned
 
Drives: 2009 E-90 M3 space gray
Join Date: Nov 2008
Location: Deutschland KreisTrier auf Autobahn 64 & Tucson AZ

Posts: 1,085
iTrader: (1)

Try the DIY thread!
Trier Germany is offline   Luxembourg
0
Reply With Quote
      05-28-2010, 01:43 PM   #3
1sikbmr
Brigadier General
 
1sikbmr's Avatar
 
Drives: E90 M3 6MT
Join Date: Mar 2010
Location: New York

Posts: 3,271
iTrader: (14)

it is really simple...
1. jack up the car
2. loosen the two clamps holding the connecting pipes to the x-pipes with, I believe is a 17 socket.
3. Loosen the two bolts holding the exhaust up with a 14 socket. There are two on each side of the exhaust. They are a little hard to get to. Look for them and make sure that you have good clearance to loosen it so that you don't bend anything or hit the bumper. On the passenger side there is a ground wire connected to the exhaust with a bolt. loosen that also and push the wire back.
4. There are 4 rubber clamps holding up the exhaust. These are a super PITA!!! to remove. What I did was use some WD-40 to give it some lube then take a pry bar and a flat and went to work removing them. There are two if you look in the mesh in the back holding the exhaust and two a little further up holding up the connecting pipes. Try not to bend the rubber too much as they will start to crack and probably will pop.
5. put back the new exhaust in the exact opposite order.

Good Luck
__________________

E90 ///M3 6MT Atlantis Blue - Fox red
ESS VT1-550|Gloss black grilles/Gold gills|V1 hardwire|Filled reflectors|ZHP lighted shift knob|Volk TE37 Gloss Black|Mode Carbon GT4 Lip|Umnitza V4 full blackout kit|Agency Power exhaust|Sosi x-pipe|BMW Performance Steering Wheel V1|
1sikbmr is offline  
0
Reply With Quote
      05-28-2010, 02:00 PM   #4
mike2010m3
Private
 
mike2010m3's Avatar
 
Drives: 2010 bmw m3
Join Date: Mar 2010
Location: florida

Posts: 66
iTrader: (0)

thanks man.
__________________
2010 bmw m3 black on black every option.
led angel eyes
mike2010m3 is offline  
0
Reply With Quote
      05-28-2010, 02:24 PM   #5
TonyTone
Major
 
TonyTone's Avatar
 
Drives: M3 VERT
Join Date: Jan 2008
Location: FL

Posts: 1,179
iTrader: (0)

Send a message via Skype™ to TonyTone
Just take your time and have a helper!

Goodluck
__________________
Tony Rivera
Flickr l Facebook
TonyTone is offline   United_States
0
Reply With Quote
      05-28-2010, 04:08 PM   #6
major_kusanagi
SWARM & COIN
 
major_kusanagi's Avatar
 
Drives: 09 AW/FR/CF E92 M3
Join Date: Jan 2009
Location: SF, CA

Posts: 465
iTrader: (3)

This should help: http://www.akrapovic.com/typo3conf/e...90_92_93_b.pdf

I used the same instructions to install and uninstall a couple of different exhausts.

Good luck!!
major_kusanagi is offline   United_States
0
Reply With Quote
      05-28-2010, 04:20 PM   #7
J08M3
Major General
 
J08M3's Avatar
 
Drives: 2011 M3 COUPE
Join Date: May 2008
Location: NEW YORK

Posts: 6,012
iTrader: (8)

Quote:
Originally Posted by 1sikbmr View Post
4. There are 4 rubber clamps holding up the exhaust. These are a super PITA!!! to remove. What I did was use some WD-40 to give it some lube then take a pry bar and a flat and went to work removing them.
+1 I did the same, those things are a pain in the ass. I guess there is some special tool they make for them, but if you don't do it all the time it's probably not worth it.
__________________
J08M3 is offline   United_States
0
Reply With Quote
      05-28-2010, 04:29 PM   #8
major_kusanagi
SWARM & COIN
 
major_kusanagi's Avatar
 
Drives: 09 AW/FR/CF E92 M3
Join Date: Jan 2009
Location: SF, CA

Posts: 465
iTrader: (3)

It's a lot easier to unbolt the metal parts to which the rubber clamps are attached. Once they are off the car, very easy to pull out.

Quote:
Originally Posted by J08M3 View Post
+1 I did the same, those things are a pain in the ass. I guess there is some special tool they make for them, but if you don't do it all the time it's probably not worth it.
major_kusanagi is offline   United_States
0
Reply With Quote
      05-28-2010, 05:35 PM   #9
Suprane
Second Lieutenant
 
Suprane's Avatar
 
Drives: 09 M3 E90
Join Date: Jul 2009
Location: Big D

Posts: 280
iTrader: (0)

Here's a a couple of threads that helped me when I did it :

http://www.m3post.com/forums/showthread.php?t=299777

http://www.m3post.com/forums/showthr...ight=shiblanor
__________________
09 E90 M3 DCT SSII Carbon Blk, Eisenmann Sport, RAC 19"RG63 on 255/275 UltracS, Dark Sidemkrs/Reflectrs/Grills, BMC Filter, LUX H8 V3 LEDs, V1 H/W, Ultimate Pedals & 30% Tint
Suprane is offline   United_States
0
Reply With Quote
      06-01-2010, 06:19 PM   #10
riyatch
Lieutenant
 
riyatch's Avatar
 
Drives: e90 M3
Join Date: Jul 2007
Location: Vegas

Posts: 473
iTrader: (1)

Quote:
Originally Posted by major_kusanagi View Post
This should help: http://www.akrapovic.com/typo3conf/e...90_92_93_b.pdf

I used the same instructions to install and uninstall a couple of different exhausts.

Good luck!!
I was looking over these instructions and it shows them using some copper anti-seize paste on the bolts and ceramic grease at the connecting pipes. Is it really necessary to use this stuff. Havent heard of others using this stuff when installing other brands of exhausts.
riyatch is offline  
0
Reply With Quote
      06-01-2010, 07:41 PM   #11
J08M3
Major General
 
J08M3's Avatar
 
Drives: 2011 M3 COUPE
Join Date: May 2008
Location: NEW YORK

Posts: 6,012
iTrader: (8)

^--- I didn't use it on the bolts, just a little on the connecting pieces and tips so they would slide together nicely
__________________
J08M3 is offline   United_States
0
Reply With Quote
      06-01-2010, 09:42 PM   #12
major_kusanagi
SWARM & COIN
 
major_kusanagi's Avatar
 
Drives: 09 AW/FR/CF E92 M3
Join Date: Jan 2009
Location: SF, CA

Posts: 465
iTrader: (3)

+1
Quote:
Originally Posted by J08M3 View Post
^--- I didn't use it on the bolts, just a little on the connecting pieces and tips so they would slide together nicely
major_kusanagi is offline   United_States
0
Reply With Quote
      06-02-2010, 12:33 PM   #13
riyatch
Lieutenant
 
riyatch's Avatar
 
Drives: e90 M3
Join Date: Jul 2007
Location: Vegas

Posts: 473
iTrader: (1)

thanks for the responses. any ideas where the ceramic grease can be picked up locally? checked the local autoparts store with no luck.
riyatch is offline  
0
Reply With Quote
Post Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 03:03 AM.




m3post
Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST