|
|
03-17-2018, 08:36 AM | #1 |
I got lei'd
841
Rep 7,593
Posts |
Part find help for intake elbow (rubber sleeve/coupler)
I’m trying to find another rubber sleeve/coupler for the side closest to the plenum. AFE’s sleeve looks wider which is what I need. Agency power’s is too narrow and would slip off. I’ve looked at some auto stores and Home Depot.
I’m betting a plumbing store might have one but if anyone knows a website to refer too. It would be 20” diameter, 2” wide and flexible |
03-17-2018, 10:59 AM | #6 |
Brigadier General
2383
Rep 3,726
Posts
Drives: 2018 M2
Join Date: Mar 2014
Location: Boston, MA
|
|
Appreciate
0
|
03-17-2018, 11:02 AM | #7 |
I got lei'd
841
Rep 7,593
Posts |
here's another device, imagine placing this on full suction
but for serious, need help finding a part |
Appreciate
0
|
03-17-2018, 11:05 AM | #8 |
Lieutenant General
11575
Rep 12,714
Posts |
AFE makes a similar part... it's going to be the same size as the plenum no matter what else it is tightening up to.
__________________
Instagram; @roastbeefmike
|
Appreciate
0
|
03-17-2018, 12:00 PM | #9 | |
Brigadier General
2383
Rep 3,726
Posts
Drives: 2018 M2
Join Date: Mar 2014
Location: Boston, MA
|
Quote:
Home Depot prob would have something just not that big. Maybe a pool supply store idk |
|
Appreciate
0
|
03-17-2018, 02:03 PM | #10 |
Lieutenant General
5179
Rep 10,557
Posts |
Just determine the round diameter and see if a silicone coupler is available in that size. They are usually 3-4 inches wide. Like for a diesel truck turbo intake.
|
Appreciate
0
|
03-17-2018, 02:06 PM | #11 |
Brigadier General
2383
Rep 3,726
Posts
Drives: 2018 M2
Join Date: Mar 2014
Location: Boston, MA
|
4” is def too small and He said 20” diameter which I assume he meant circumference which would be about 6 1/3”
|
Appreciate
0
|
03-17-2018, 06:07 PM | #13 |
Lieutenant General
11575
Rep 12,714
Posts |
you're chasing a wild goose trying to find a non-intended solution. just buy someone's aftermarket intake coupler and be done with it.
__________________
Instagram; @roastbeefmike
|
Appreciate
0
|
03-17-2018, 07:10 PM | #14 |
Brigadier General
2383
Rep 3,726
Posts
Drives: 2018 M2
Join Date: Mar 2014
Location: Boston, MA
|
No clue I have the stock one so never needed to measure. I’d guess the od since that’s easiest and his is thin walled carbon so prob not much diff. OP if you have the stock one still you can cut the ends off that and try. Or just use some bead seal and use the skinny one you think will slip off
|
Appreciate
0
|
03-17-2018, 07:37 PM | #15 |
Lieutenant General
5179
Rep 10,557
Posts |
Should measure ID of the existing rubber. If it is 6.00 or 6.5 or 7 or 7.5 or 8 inches you can easily find a coupler. If you need quarter steps it will be harder to find.
http://www.intakehoses.com/mm5/merch...egory_Code=SS8 http://www.hps-siliconehoses.com/cat...gory/view/id/8 |
Appreciate
0
|
03-18-2018, 12:45 AM | #16 |
I got lei'd
841
Rep 7,593
Posts |
|
Appreciate
0
|
03-27-2018, 03:15 AM | #19 |
I got lei'd
841
Rep 7,593
Posts |
|
Appreciate
0
|
03-02-2021, 04:37 PM | #21 |
Enlisted Member
150
Rep 42
Posts |
|
Appreciate
0
|
03-03-2021, 08:55 AM | #22 |
I got lei'd
841
Rep 7,593
Posts |
|
Appreciate
0
|
Post Reply |
Bookmarks |
Thread Tools | Search this Thread |
|
|