|
|
02-01-2013, 01:00 AM | #1 |
New Member
1
Rep 12
Posts |
dyno sheet for my Dinan 4.6L
Im kinda disappointed in these numbers. does this seem right to you guys? Dinan claims 500+ HP on the motor. I am missing the Xpipe...
Mods: 4.6L board & stroked, Dinan 3.62 differential, dinan throttle bodies, Dinan free flow exhaust, Dinan High Flow intake, Dinan st2 front/rear break kit. Dinan stage 3 suspension. 380HP/ 296 TQ Last edited by livfastdieyng; 02-01-2013 at 02:20 AM.. |
02-01-2013, 01:06 AM | #2 |
Major
167
Rep 1,159
Posts |
Wowww Dinan 4.6l! I'm soo jealous, but as you were saying I was expected much higher numbers than that. You should get at least around 450whp with the engine, exhaust, intake. With the x-pipe you should probably get another +20whp?
A stock M3 gets around 340-360 on the dyno. But then again it depends on the dyno that you used as well as the temperature and what not. What dyno were you using? Because something doesn't seem right.
__________________
M3.E90 JZB Coded.GTSDCT.BomizValved.TurnerTestPipes.ResDelete .EurochargedTune.AAFilter.HRER40s
|
Appreciate
0
|
02-01-2013, 02:33 AM | #3 |
I'm suckin gas but I'm haulin ass
57
Rep 783
Posts |
I would have expected higher numbers. My car has MS Stage II Intake, MS Pullies, full catless Borla exhaust and I'm putting down 386hp/278tq in comparison
|
Appreciate
0
|
02-01-2013, 07:57 AM | #5 |
Second Lieutenant
13
Rep 227
Posts
Drives: E92 M3- AW
Join Date: Jan 2012
Location: Redding, CT
|
+1.
Seems like most people here use Dynojets. If you were on a Mustang or DynoDynamics you will definitely see significantly lower numbers depending on the correction utilized.
__________________
Alpine White E92 M3 - 6MT
ESS Tuned |
Appreciate
0
|
02-01-2013, 09:21 AM | #6 |
Second Lieutenant
33
Rep 203
Posts |
Please post the dyno sheets and log some data. it is difficult to say ANYTHING about your results. Without the supplementary data the opinions here are conjecture. Go back to the same dyno and log the following at a minimum.
-IATs -AFRs -Ambient If the DME is reading IATs north of 100* F, this could explain your low numbers as the car will pull timing and the power will be neutered. Now if your IATs are within an acceptable range of ambient (15-20 degrees F) and these are your results, I may have concerns. You would be shocked how playing with the cooling fans can impact your results. Mike p.s. On another note, Dinan tunes have been notoriously conservative since the E36 days. Have you considered a more reputable E9X tuner with VANOS and cam control for your car? Ahem... NickG, Evolve, BMP?
__________________
Naturally Agitated - S54B34 CSL Clone - 395 285 SAE on 91 pump - 3150 lbs - P car and E9X eater.
|
Appreciate
0
|
02-01-2013, 09:26 AM | #7 |
Colonel
180
Rep 2,446
Posts
Drives: '11 E92 M3 DCT
Join Date: Jun 2011
Location: Calgary, Ab
|
Pretty sure those are Mustang numbers, but even at those numbers an additional 50 pounds of torque is pretty good.
Did you dyno before stroking? Post the dyno sheet
__________________
11' E92 M3 Space Grey | DCT | ESS VT2- 625 | Gintani Race (valved) + Quad Res Catless X-Pipe | KW Sleeve's | GC Camber Plates|Arkym Diffuser | Vorsteiner VRS Lip | P3 Boost Guage | Stud Conversion PHOTO's: Click Here ESS VT2 625 PHOTOS: Click Here |
Appreciate
0
|
02-01-2013, 10:05 AM | #8 |
BimmerPost Supporting Vendor
307
Rep 13,093
Posts
Drives: BPMsport 2012 E92 M3
Join Date: Jun 2011
Location: Kansas
iTrader: (45)
Garage List 2013 Nissan GTR [0.00]
2019 Sierra Denali ... [0.00] 1999 Nissan Silvia [0.00] 1999 Nissan Skyline ... [0.00] 1998 Toyota Supra [0.00] |
Does Dinan provide any documentation on the motor when you purchase it?
|
Appreciate
0
|
02-01-2013, 06:25 PM | #9 |
First Lieutenant
115
Rep 331
Posts |
Might have something to do with engine being board, not bored. I kid, +1 on the dyno, check which one go try a dynojet, report back. Curious to see the results, plz post before and after if possible.
|
Appreciate
0
|
02-01-2013, 08:02 PM | #12 |
BimmerPost Supporting Vendor
731
Rep 3,735
Posts |
That doesn't make sense at all, unless they forgot to install the parts that actually increase displacement.
For your reference, my car makes 404 RWHP on a DynoJet with full exhaust and tune and thats it. 91 octane. |
Appreciate
0
|
02-02-2013, 12:34 AM | #13 |
Lieutenant Colonel
163
Rep 1,506
Posts
Drives: '15 FO M4
Join Date: Sep 2010
Location: NorCal Bay Area
|
I think he bought the car with the stroker on it already
__________________
Fire Orange F82 Built by Alekshop | Pure Stage 2 Turbos | Akrapovic Evolution and Downpipes | ESS T-500 Performance ECU Software | Evolution Racewerks Chargepipes | Gruppe M CAI | Awron Gauge w/ Valve Control | KW Clubsport | Brembo GT 380 F&R | 19" BBS FI-R | BMW Performance Seats, Aero, and Steering Wheel | Vorsteiner Diffuser | IND Cosmetics
|
Appreciate
0
|
02-04-2013, 12:10 PM | #14 |
Private First Class
3
Rep 159
Posts |
Depends on the dyno used. The only thing that should matter is what the car gained over stock on the same dyno. I have seen stock m3's dyno 320 whp to 370 whp on different dyno's so I would not be worried about the numbers unless you have a reference on the same dyno.
|
Appreciate
0
|
02-04-2013, 12:17 PM | #15 |
Banned
1770
Rep 6,696
Posts
Drives: F30 340i
Join Date: Jan 2009
Location: San Diego,CA
|
cmon op give some answers
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|