|
|
|
Post Reply |
|
Thread Tools | Search this Thread |
05-06-2015, 03:26 PM | #1 |
Enlisted Member
9
Rep 39
Posts |
E92 2009 M3 w/ Mods Unable to Read Using NCSExpert or INPA
I was trying to read and feature code a friends 2009 E92 M3 (Production date of the car is 2009-01-28) last week for his LCI tail light conversion but was unable to even read the car using NCSExpert or INPA. Using the same coding setup I have no issues reading and coding other cars, including my own 2008 E92 M3.
His car has a lot of mods done to it, almost anything I can think of, but there are a few that I know would interact with the ECU's. His BMW Performance Steering Wheel I know taps into some of the cables the ODB connector uses (from the DIY's I looked up), and his ESS Supercharger tune would probably have been done over ODB. Can either of these be preventing from even reading the car? NCSExpert reports a faulty VIN (I've attached the error.log below), INPA reports On and Ignition On, but when trying to read the error codes I get "Data Transmission to Interface Disturbed". I've tried reading the car with 50.2 (30.04.2013) and 51.2 (03.07.2013). I've read & coded many cars older and newer than his without issue. Code:
[12:20:41.673] [2015-05-01] [SERIE] 2000 Error LFCDHDIA.CPP (A_PL2FRX.IPS/IPO) CDHapiResultText 1 [12:20:41.673] [2015-05-01] [SERIE] Fehler in EDIABAS oder in SG-Beschreibungsdatei IFH-0003: Datenuebertragung HOST/Interface gestoert FRM_87 [12:20:41.780] [2015-05-01] [SERIE] 2000 Error COAPI2.CPP coapiRunCabd 6 [12:20:41.780] [2015-05-01] [SERIE] Fehler in EDIABAS oder in SG-Beschreibungsdatei FA_READ [12:20:41.782] [2015-05-01] [SERIE] 2000 Error COAPI4.CPP coapiReadAuftrag 4 [12:20:41.782] [2015-05-01] [SERIE] Fehler in EDIABAS oder in SG-Beschreibungsdatei FA_READ: A_PL2FRX [12:20:41.869] [2015-05-01] [SERIE] 2000 Error LFCDHDIA.CPP (A_PL2FRX.IPS/IPO) CDHapiResultText 1 [12:20:41.869] [2015-05-01] [SERIE] Fehler in EDIABAS oder in SG-Beschreibungsdatei IFH-0003: Datenuebertragung HOST/Interface gestoert FRM_87 [12:20:41.978] [2015-05-01] [SERIE] 2000 Error COAPI2.CPP coapiRunCabd 6 [12:20:41.978] [2015-05-01] [SERIE] Fehler in EDIABAS oder in SG-Beschreibungsdatei FA_READ [12:20:41.980] [2015-05-01] [SERIE] 2000 Error COAPI4.CPP coapiReadAuftrag 4 [12:20:41.980] [2015-05-01] [SERIE] Fehler in EDIABAS oder in SG-Beschreibungsdatei FA_READ: A_PL2FRX [12:20:42.062] [2015-05-01] [SERIE] 2000 Error LFCDHDIA.CPP (A_E65CAS.IPS/IPO) CDHapiResultText 1 [12:20:42.062] [2015-05-01] [SERIE] Fehler in EDIABAS oder in SG-Beschreibungsdatei IFH-0003: Datenuebertragung HOST/Interface gestoert CAS [12:20:42.169] [2015-05-01] [SERIE] 2000 Error COAPI2.CPP coapiRunCabd 6 [12:20:42.169] [2015-05-01] [SERIE] Fehler in EDIABAS oder in SG-Beschreibungsdatei FA_READ [12:20:42.172] [2015-05-01] [SERIE] 2000 Error COAPI4.CPP coapiReadAuftrag 4 [12:20:42.172] [2015-05-01] [SERIE] Fehler in EDIABAS oder in SG-Beschreibungsdatei FA_READ: A_E65CAS [12:20:42.173] [2015-05-01] [SERIE] 1000 Warning COAPI.CPP coapiReadFgNr 9 [12:20:42.173] [2015-05-01] [SERIE] Fehler CAS ================================================================================(2) [12:20:42.286] [2015-05-01] [SERIE] 2000 Error LFCDHDIA.CPP (A_E65CAS.IPS/IPO) CDHapiResultText 1 [12:20:42.286] [2015-05-01] [SERIE] Fehler in EDIABAS oder in SG-Beschreibungsdatei IFH-0003: Datenuebertragung HOST/Interface gestoert CAS [12:20:42.397] [2015-05-01] [SERIE] 2000 Error COAPI2.CPP coapiRunCabd 6 [12:20:42.397] [2015-05-01] [SERIE] Fehler in EDIABAS oder in SG-Beschreibungsdatei FGNR_LESEN [12:20:42.401] [2015-05-01] [SERIE] 2000 Error COAPI.CPP coapiReadFgNr 12 [12:20:42.401] [2015-05-01] [SERIE] Fehler in EDIABAS oder in SG-Beschreibungsdatei FGNR_LESEN: A_E65CAS ================================================================================(2) |
05-07-2015, 06:22 PM | #3 |
Enlisted Member
9
Rep 39
Posts |
I contacted ESS about the ECU flash for the supercharger, you might be right. This was the response:
"Yes, the ECU is read locked on the portion that contains our software. You do no need to access this for anything else than engine calibrations which should not be touched at all. " |
Appreciate
0
|
05-08-2015, 02:22 AM | #4 | |
Banned
522
Rep 1,527
Posts |
Quote:
|
|
Appreciate
0
|
05-08-2015, 07:01 PM | #6 | |
Banned
522
Rep 1,527
Posts |
Quote:
|
|
Appreciate
0
|
05-17-2015, 02:53 PM | #7 | ||
Lord Scrip
1813
Rep 3,013
Posts
Drives: 2011 M3 Coupe
Join Date: Jan 2012
Location: LA,Ca
|
Quote:
__________________
|
||
Appreciate
0
|
Post Reply |
Bookmarks |
|
|