FS: Track tire wheel set: Apex/Yoko ADO8-Pics up

saildoc · 04-29-2011, 02:00 PM

BIMMERPOST / Classifieds

Asking Price:

None

Item Interest

SOLD

Lightly used track wheel tire setup. Used at three track day driving events. More than half the tread is left. No off track events or impacts to rims. TPMS installed and included. I am getting a spec boxster so I no longer will track my M3. No rubbing or clearance issues noted. Very heat resistant tires with no greasy feeling when hot. Ran right up to the back of Porsche GT3's with this set up. Can be used as street setup. Purchased August 2010, there is a factory warranty that covers them for two years: Warranty Summary: 2 year Structural warranty. 1 year limited warranty guarantees wheels will be free from defects in materials, workmanship and paint finish under normal and reasonable use.
I measured the tire tread depth. Near the shoulder they are all at least 4/32 with the front left slightly shy and the other 3 slightly over. In the middle of the tread they are all at least 6/32. According to the data on Tire Rack they started at 10/32 so there is a little more than half the tread left.

Wheels: Apex: Matt Black powder coated:
Front:
Diameter: 18"
Width: 9.5"
Offset: 22mm
Lug Pattern: 5x120mm
Centerbore: 72.6mm
Weight: 19.10lbs

Rear:
Diameter: 18"
Width: 10"
Offset: 25mm
Lug Pattern: 5x120mm
Centerbore: 72.6mm
Weight: 19.95lbs
http://www.apexraceparts.com/ARC-8-1...set_p_133.html
Tires: ADVAN Neova AD08 Yokohama's: 265/35R18 and 285/30R18
http://www.tirerack.com/tires/tires....VAN+Neova+AD08
TPMS: Behr through tire rack

SOLD SOLD SOLD

chris s · 04-29-2011, 02:05 PM

Do you know the offsets?

Martin_D · 04-29-2011, 02:37 PM

Chris-

Front et22
Rear et25

IMG · 04-29-2011, 02:38 PM

Not a bad deal !!!

Dan Halen · 04-29-2011, 02:41 PM

can a spacer be used to make these clear 380 brembo BBK? or is it the diameter that caused problems with the brembos, afaik- these clear the stoptech 380s, correct?

Martin_D · 04-29-2011, 02:45 PM

Quote:

Originally Posted by Dan Halen

can a spacer be used to make these clear 380 brembo BBK? or is it the diameter that caused problems with the brembos, afaik- these clear the stoptech 380s, correct?

They clear Stoptech BBK. They do not clear the 380 Brembo BBK because it is used for nothing. It is all marketing. Switch to a smaller rotor.

chris s · 04-29-2011, 02:50 PM

Quote:

Originally Posted by Martin_D

Chris-

Front et22
Rear et25

Thanks Martin!

Quote:

Originally Posted by img

Not a bad deal !!!

It's a pretty good deal!!!

STALKER · 04-29-2011, 05:37 PM

If you part out the tires, let me know.
Interested in the tires, not the rims.
Thanks.

Pics please.

persian54 · 04-29-2011, 05:42 PM

Quote:

Originally Posted by STALKER

If you part out the tires, let me know.
Interested in the tires, not the rims.
Thanks.

Pics please.

And I'm interested in the rims if the price is right

ring007 · 04-29-2011, 10:09 PM

I'm very interested and I'm at the PCA event at Hallett this weekend. Any chance you're planning to be here ? I have 380mm front brembo's but at this price worth changing to smaller front rotors.
Let me know.

Quote:

Originally Posted by saildoc

Lightly used track wheel tire setup. Used at three track day driving events. More than half the tread is left. No off track events or impacts to rims. TPMS installed and included. I am getting a spec boxster so I no longer will track my M3. No rubbing or clearance issues noted. Very heat resistant tires with no greasy feeling when hot. Ran right up to the back of Porsche GT3's with this set up.
Wheels: Apex: Matt Black powder coated: 18x9.5 fr 18x10 rear
http://www.apexraceparts.com/ARC-8-1...set_p_133.html
Tires: ADVAN Neova AD08 Yokohama's: 265/35R18 and 285/30R18
http://www.tirerack.com/tires/tires....VAN+Neova+AD08
TPMS: Behr through tire rack

I will post photos this weekend.
Replacement cost for this set up is over $2600, I will let them go for $1300, you pay shipping. Please email for questions. Thanks for looking.

saildoc · 04-29-2011, 11:11 PM

Quick pics of the set up.

saildoc · 04-30-2011, 10:06 AM

Added a few more pics this am
BTW: these were purchased new in August 2010. I also notice I am missing one APEX cap. They are $10. Will adjust price accordingly. http://www.apexraceparts.com/APEX-Wh...arge_p_62.html

chris s · 04-30-2011, 10:54 AM

Anyone have this setup or similar sizing and lowered on H&R or the like?

Any rubbing up front to be concerned about?

saildoc · 04-30-2011, 01:15 PM

I have the stock ride height, no problems with rubbing and I have hit the bump stops a few times. I think if you have the stock bump stops the travel geometry is the same, they clear the struts and shocks without issue so I think it should be the same for your case. You might want to check with apex racing on that one.

IMG · 04-30-2011, 03:00 PM

Im interested in the wheels,PM a price plz !

persian54 · 04-30-2011, 04:59 PM

you're not interested in trades are you?

saildoc · 04-30-2011, 05:04 PM

At this point these track wheels are coming off the car, the OEM 19's are going back on and I am going to drive the car on the street again. I really don't need any other tires or wheels as I will be selling the M3 this summer. It would be better to leave the combo assembled as a package-bolt on and go for whomever ends up with them. The M3 is a heavy car and as you can see from the pics they held up really well at the hot track. They will be a very fast and reliable track tire for the next owner. I appreciate all the interest.

xchosun1x · 04-30-2011, 05:07 PM

can you please give me a price quote shipped to 90014?

armorrig · 04-30-2011, 05:10 PM

Damn very tempting.

Do you have better side profile pics with the front wheels straight?

What's your zip? Do you know the weight with the tires so I can get a shipping quote?

Or if you can get one to 91106?

Thanks.

armorrig · 04-30-2011, 05:12 PM

Quote:

Originally Posted by xchosun1x

can you please give me a price quote shipped to 90014?

What's up man? Did you move from Pasadena to LA?

persian54 · 04-30-2011, 07:20 PM

Quote:

Originally Posted by xchosun1x

can you please give me a price quote shipped to 90014?

your set is already a great track set lol....

If there is anyone in LA who wants the tires... that would be great as I want the rims

saildoc · 05-01-2011, 02:37 PM

I measured the tire tread depth. Near the shoulder they are all at least 4/32 with the front left slightly shy and the other 3 slightly over. In the middle of the tread they are all at least 6/32. According to the data on Tire Rack they started at 10/32 so there is a little more than half the tread left.

04-29-2011, 02:00 PM	#1
saildoc Private First Class 41 Rep 194 Posts Drives: 2012 Porsche Cayman R Join Date: Apr 2007 Location: oklahoma city iTrader: (1)	SOLD: Apex Arc Wheel/ Yoko AD08 tire setup-track or street BIMMERPOST / Classifieds Asking Price: None Item Interest SOLD Lightly used track wheel tire setup. Used at three track day driving events. More than half the tread is left. No off track events or impacts to rims. TPMS installed and included. I am getting a spec boxster so I no longer will track my M3. No rubbing or clearance issues noted. Very heat resistant tires with no greasy feeling when hot. Ran right up to the back of Porsche GT3's with this set up. Can be used as street setup. Purchased August 2010, there is a factory warranty that covers them for two years: Warranty Summary: 2 year Structural warranty. 1 year limited warranty guarantees wheels will be free from defects in materials, workmanship and paint finish under normal and reasonable use. I measured the tire tread depth. Near the shoulder they are all at least 4/32 with the front left slightly shy and the other 3 slightly over. In the middle of the tread they are all at least 6/32. According to the data on Tire Rack they started at 10/32 so there is a little more than half the tread left. Wheels: Apex: Matt Black powder coated: Front: Diameter: 18" Width: 9.5" Offset: 22mm Lug Pattern: 5x120mm Centerbore: 72.6mm Weight: 19.10lbs Rear: Diameter: 18" Width: 10" Offset: 25mm Lug Pattern: 5x120mm Centerbore: 72.6mm Weight: 19.95lbs http://www.apexraceparts.com/ARC-8-1...set_p_133.html Tires: ADVAN Neova AD08 Yokohama's: 265/35R18 and 285/30R18 http://www.tirerack.com/tires/tires....VAN+Neova+AD08 TPMS: Behr through tire rack SOLD SOLD SOLD Last edited by saildoc; 05-13-2011 at 11:50 AM.. Reason: SOLD
	Appreciate 0 Tweet Quote

04-29-2011, 02:05 PM	#2
chris s Major General 1250 Rep 6,912 Posts Drives: 2022 Dravit G80 M3 Join Date: Oct 2008 Location: New York iTrader: (12)	Do you know the offsets? __________________ 2022 Dravit/Fiona M3cx - Dinan midpipe w/VC, NW Carbonhaus CF, AST Springs, FC Spacers...more to come! 2016 Indi F80 M3 - SMB\|Amaro \| Mode Carbon \| ESS \| Akra EVO \| KW HAS...SOLD 2012 MR e92 M3 DCT, ESS SC, Brembo BBK, BBS FI... GONE but not forgotten! 2008 AW e92 M3 6MT, ESS SC, BBS LM's...SOLD!
	Appreciate 0 Quote

04-29-2011, 02:37 PM	#3
Martin_D Lieutenant Colonel 102 Rep 1,787 Posts Drives: Ford Super Duty Join Date: Nov 2009 Location: Raleigh, NC iTrader: (34)	Chris- Front et22 Rear et25
	Appreciate 0 Quote

04-29-2011, 02:38 PM	#4
IMG 1122 Rep 7,690 Posts Drives: E36 M3 Track car,Ess E90 M3 DD Join Date: Feb 2008 Location: Location iTrader: (6)	Not a bad deal !!!
	Appreciate 0 Quote

04-29-2011, 02:41 PM	#5
Dan Halen Sheetrock Intl. 28 Rep 128 Posts Drives: E92, R6 SBK, etc, etc.. Join Date: Mar 2011 Location: SF iTrader: (2)	can a spacer be used to make these clear 380 brembo BBK? or is it the diameter that caused problems with the brembos, afaik- these clear the stoptech 380s, correct?
	Appreciate 0 Quote

04-29-2011, 05:37 PM	#8
STALKER Brigadier General 169 Rep 3,831 Posts Drives: 997.2 GT3, Golf R Join Date: Feb 2009 Location: Toronto, ON iTrader: (5)	If you part out the tires, let me know. Interested in the tires, not the rims. Thanks. Pics please. __________________
	Appreciate 0 Quote

04-29-2011, 11:11 PM	#11
saildoc Private First Class 41 Rep 194 Posts Drives: 2012 Porsche Cayman R Join Date: Apr 2007 Location: oklahoma city iTrader: (1)	Pics Quick pics of the set up. Attached Images
	Appreciate 0 Quote

04-30-2011, 10:06 AM	#12
saildoc Private First Class 41 Rep 194 Posts Drives: 2012 Porsche Cayman R Join Date: Apr 2007 Location: oklahoma city iTrader: (1)	More pics Added a few more pics this am BTW: these were purchased new in August 2010. I also notice I am missing one APEX cap. They are $10. Will adjust price accordingly. http://www.apexraceparts.com/APEX-Wh...arge_p_62.html Attached Images
	Appreciate 0 Quote

04-30-2011, 10:54 AM	#13
chris s Major General 1250 Rep 6,912 Posts Drives: 2022 Dravit G80 M3 Join Date: Oct 2008 Location: New York iTrader: (12)	Anyone have this setup or similar sizing and lowered on H&R or the like? Any rubbing up front to be concerned about? __________________ 2022 Dravit/Fiona M3cx - Dinan midpipe w/VC, NW Carbonhaus CF, AST Springs, FC Spacers...more to come! 2016 Indi F80 M3 - SMB\|Amaro \| Mode Carbon \| ESS \| Akra EVO \| KW HAS...SOLD 2012 MR e92 M3 DCT, ESS SC, Brembo BBK, BBS FI... GONE but not forgotten! 2008 AW e92 M3 6MT, ESS SC, BBS LM's...SOLD!
	Appreciate 0 Quote

04-30-2011, 01:15 PM	#14
saildoc Private First Class 41 Rep 194 Posts Drives: 2012 Porsche Cayman R Join Date: Apr 2007 Location: oklahoma city iTrader: (1)	no rubbing I have the stock ride height, no problems with rubbing and I have hit the bump stops a few times. I think if you have the stock bump stops the travel geometry is the same, they clear the struts and shocks without issue so I think it should be the same for your case. You might want to check with apex racing on that one.
	Appreciate 0 Quote

04-30-2011, 03:00 PM	#15
IMG 1122 Rep 7,690 Posts Drives: E36 M3 Track car,Ess E90 M3 DD Join Date: Feb 2008 Location: Location iTrader: (6)	Im interested in the wheels,PM a price plz !
	Appreciate 0 Quote

04-30-2011, 04:59 PM	#16
persian54 Lieutenant General 922 Rep 15,818 Posts Drives: M760/G83M4 Join Date: Jun 2009 Location: The Valley, SoCal iTrader: (298)	you're not interested in trades are you? __________________ From E93 335i to E89 Z4 to E93 M3/E89 Z4 to E350/SL550
	Appreciate 0 Quote

04-30-2011, 05:04 PM	#17
saildoc Private First Class 41 Rep 194 Posts Drives: 2012 Porsche Cayman R Join Date: Apr 2007 Location: oklahoma city iTrader: (1)	trades and splitting At this point these track wheels are coming off the car, the OEM 19's are going back on and I am going to drive the car on the street again. I really don't need any other tires or wheels as I will be selling the M3 this summer. It would be better to leave the combo assembled as a package-bolt on and go for whomever ends up with them. The M3 is a heavy car and as you can see from the pics they held up really well at the hot track. They will be a very fast and reliable track tire for the next owner. I appreciate all the interest.
	Appreciate 0 Quote

04-30-2011, 05:07 PM	#18
xchosun1x Track Duty 266 Rep 2,467 Posts Drives: Track build 08 E92 M3 DCT Join Date: Nov 2009 Location: Los Angeles iTrader: (14)	can you please give me a price quote shipped to 90014?
	Appreciate 0 Quote

04-30-2011, 05:10 PM	#19
armorrig Brigadier General 77 Rep 3,268 Posts Drives: Tamiya Join Date: Feb 2010 Location: So.Cal. iTrader: (2)	Damn very tempting. Do you have better side profile pics with the front wheels straight? What's your zip? Do you know the weight with the tires so I can get a shipping quote? Or if you can get one to 91106? Thanks. __________________
	Appreciate 0 Quote

05-01-2011, 02:37 PM	#22
saildoc Private First Class 41 Rep 194 Posts Drives: 2012 Porsche Cayman R Join Date: Apr 2007 Location: oklahoma city iTrader: (1)	Tread depth measured I measured the tire tread depth. Near the shoulder they are all at least 4/32 with the front left slightly shy and the other 3 slightly over. In the middle of the tread they are all at least 6/32. According to the data on Tire Rack they started at 10/32 so there is a little more than half the tread left.
	Appreciate 0 Quote