BMW M3 Forum (E90 E92)

BMW Garage BMW Meets Register Search Today's Posts Mark Forums Read


Go Back   M3Post - BMW M3 Forum > E90/E92 M3 Technical Topics > DIY Guides/ Discussions
 
Evolve Automotive
Post Reply
 
Thread Tools Search this Thread
      11-26-2013, 11:05 PM   #67
warranty
New Member
1

 
Drives: 2008 M3 sedan
Join Date: Jan 2010
Location: California


Posts: 25
iTrader: (1)

I did the tranny fluid change today, and at 50k miles the old fluid was pretty dark. Lifetime fluid my ass, BMW! Now the 1-2 shift seems to feel smoother (I used to have to double-clutch when cold to ensure smooth shifts) so I'm very glad I did it.

While I was under there I manually powered the pump to drain the fluid in the cooler. As another poster mentioned, I did so by slitting open the pump wire loom and scraping off the insulation on the red wire (+12V). Then I temporarily connect a battery +12V to the red wire, and connect another wire between the battery ground and the tranny case (which acts as a ground for the tranny fluid pump). I manually connect the ground wire in 15 second bursts to power the pump 3~4 times. Quite a bit more fluid were pumped out of the cooler that way...until there was just nothing more to come out of the drain hole.

As for filling the tranny, I initially filled up to the fill hole level, then I hand-tightened the old fill plug and cycled the pump for another 45~60 seconds (also in 15 second bursts). Then I think I added another ~300ml of fluid and re-installed a new fill plug that I bought (I discarded the old drain and fill plugs).

Of course, after I was all done I wrapped some high-temperature electrical tape over the pump wire that I had exposed and doubled the protection with additional wire loom just to be safe. Overall a very simple procedure--figuring out how to power the pump and cleaning up the occasional spills probably took more time than the actual procedure.

By the way, my filter mesh screen was also very clean, but since I had it out I just installed a new one that I bought along with the new crush washer.
__________________

2008 6MT M3 sedan
Appreciate 0
      02-03-2014, 01:19 PM   #68
Time Lord
Lieutenant
13

 
Time Lord's Avatar
 
Drives: E90 M3/E46 M3
Join Date: Mar 2011
Location: Ft Bragg


Posts: 424
iTrader: (5)

Was anyone's oil strainer that bad that they had to replace it?
__________________
E46/90 M3
Appreciate 0
      02-07-2014, 09:24 AM   #69
Sean05
Putcha ang ganda...
Philippines
149

 
Sean05's Avatar
 
Drives: 08 MR E92 M3
Join Date: Feb 2010
Location: Los Angeles, Brea CA.


Posts: 5,331
iTrader: (9)

Send a message via Yahoo to Sean05
Quote:
Originally Posted by Giorgia View Post
Was anyone's oil strainer that bad that they had to replace it?
no when i replaced mine at 50k or 70k it was very clean. im doing another tranny fluid at 100k im at 84k now.. that will take 3 years for me to get to 100k lol
__________________
Appreciate 0
      02-07-2014, 09:43 AM   #70
Time Lord
Lieutenant
13

 
Time Lord's Avatar
 
Drives: E90 M3/E46 M3
Join Date: Mar 2011
Location: Ft Bragg


Posts: 424
iTrader: (5)

I just changed mine at 45k miles(08) and it was black!!!!! i know that oil still works efficiantly even though its black but im glad i did it. of course more of a piece of mind.

knocked out both diff and trans fluid in 30 min. and it was my first time. thanks to the guides on this forum.

Brakes are next......
__________________
E46/90 M3
Appreciate 0
      02-07-2014, 10:10 AM   #71
Sean05
Putcha ang ganda...
Philippines
149

 
Sean05's Avatar
 
Drives: 08 MR E92 M3
Join Date: Feb 2010
Location: Los Angeles, Brea CA.


Posts: 5,331
iTrader: (9)

Send a message via Yahoo to Sean05
Quote:
Originally Posted by Giorgia View Post
I just changed mine at 45k miles(08) and it was black!!!!! i know that oil still works efficiantly even though its black but im glad i did it. of course more of a piece of mind.

knocked out both diff and trans fluid in 30 min. and it was my first time. thanks to the guides on this forum.

Brakes are next......
hmmn weird when i replaced mine at 50 or 70k i could still see some of the aluminum part and i wipe it down with a cleaner and parts were still pretty shiny.. maybe the dealer replaced mine at 30k. not sure..

yea brakes are really easy. if you dont have power tools make sure you have extensions tubes those nuts are hard to get..
__________________
Appreciate 0
      02-07-2014, 11:50 AM   #72
Time Lord
Lieutenant
13

 
Time Lord's Avatar
 
Drives: E90 M3/E46 M3
Join Date: Mar 2011
Location: Ft Bragg


Posts: 424
iTrader: (5)

Oil was black lol...... strainer was clean
__________________
E46/90 M3
Appreciate 0
      03-11-2014, 08:34 PM   #73
414hpbabyshuttle
Private First Class
1

 
Drives: e90 m3
Join Date: Jul 2013
Location: nova


Posts: 102
iTrader: (0)

Any gl4 fluid ok to use? Must use BMW fluid?
Appreciate 0
      05-09-2014, 12:57 PM   #74
werly
First Lieutenant
Taiwan
32

 
Drives: 2011 MR E92 M3
Join Date: Aug 2010
Location: SoCal


Posts: 329
iTrader: (1)

Send a message via MSN to werly
Can someone elaborate on how to put together a oil pump using OP's method?

Thanks a bunch
Appreciate 0
      05-09-2014, 02:15 PM   #75
W///
Major General
92

 
W///'s Avatar
 
Drives: 2008 E92 M3/1999 E36 M3 Coupe
Join Date: Sep 2011
Location: SC


Posts: 5,237
iTrader: (12)

Quote:
Originally Posted by werly View Post
Can someone elaborate on how to put together a oil pump using OP's method?

Thanks a bunch
Just buy one off Amazon or go to your local auto store
__________________
2008 E92 M3: Sparkling Graphite | Bamboo Beige | 6MT | CF Roof | HRE | Catless Eisenmann Race | BPM Sport | Swift | Arkym | Mode Carbon | M.Perf
Appreciate 0
      05-10-2014, 10:01 AM   #76
e92zero
Lieutenant
11

 
Drives: 2011 E92 BW
Join Date: May 2010
Location: somewhere in US


Posts: 557
iTrader: (0)

Quote:
Originally Posted by werly View Post
Can someone elaborate on how to put together a oil pump using OP's method?

Thanks a bunch
Goto your local Home Depot or OSH, grab the gray colored Spray Master bottle. (This is the best one I found so far). Unscrew the spray tip, walk over to the clear tubing isle and match the smallest clear tubing that fit. There is only one size that will fit with a leak tight seal. It will be a bit tight but it will fit. Buy a roll of that tubing.

Once you get home, open the bottle, take off the strainer inside, fill it up with oil, cut a piece of tubing to length and screw it onto the spray bottle tip. You will now have your oil pump as the OP.

Hopefully, that's detail enough. I have one of these pump for every different oil for the different cars in the family that requires pumping. Can't thank the OP enough for showing this. Very clean oil change now compare to the stupid %#&)#!*&$ pumps I used before from auto stores.
Appreciate 0
      05-24-2014, 06:14 PM   #77
jimk
Captain
United_States
25

 
jimk's Avatar
 
Drives: 2011 E90 M3 M/T
Join Date: Jun 2009
Location: 1961 Stout Street, Suite 1823, Denver CO 80294


Posts: 732
iTrader: (5)

Activating the pump w ISTA/D

For those who have ISTA/D, you can activate the pump under Activities, Engine, Manual Transmission. I used the Rheingold release:
Attached Images
           
__________________
Appreciate 0
      08-09-2014, 08:56 AM   #78
bigfy39
New Member
0

 
Drives: e46 328ci
Join Date: Oct 2010
Location: New Jersey


Posts: 27
iTrader: (0)

Hey guys,

Any tips for removing the fill/drain plugs without stripping them? I came close to stripping the fill plug on my e90 330 when trying to do this. Then again, I tried it at 110k miles (I bought the car second hand) and it was probably never touched since production.
Appreciate 0
      08-09-2014, 09:19 AM   #79
dparm
Major
United_States
25

 
dparm's Avatar
 
Drives: 2011.5 E90 M3
Join Date: Jun 2013
Location: Chicago, IL


Posts: 1,447
iTrader: (0)

Quote:
Originally Posted by bigfy39 View Post
Hey guys,

Any tips for removing the fill/drain plugs without stripping them? I came close to stripping the fill plug on my e90 330 when trying to do this. Then again, I tried it at 110k miles (I bought the car second hand) and it was probably never touched since production.

I'd hit it with some PB Blaster before, let it soak in for a bit, and then try. Make sure you have the proper wrench to apply a lot of torque instantly.
__________________
2011.5 AW M3 sedan ZCP
Appreciate 0
      09-22-2014, 09:01 PM   #80
JonM
Private First Class
23

 
Drives: E90 M3 Sedan
Join Date: Sep 2008
Location: Charleston, SC


Posts: 172
iTrader: (4)

I just did this service on my 08 M3. My car only has 42k on it and I paid the dealer to do it once before. At any rate, the reason for my post is I used my brand new Motive fluid pump when I did it. It's basically a glorified garden pressure sprayer. If you are crafty you could make your own for less. But I have rigged up so many pumps over the last 20 years and tried all kinds of cheap POS pumps, I wanted to try a nice one for once. This is it. It is a pleasure to use. I pressurized it with my compressor and it filled the transmission fluid in about 1 minute on a single charge. Love the tool. I will use it on the M coupes next and on our GMC truck too.

http://www.ecstuning.com/Search/Motive/ES2207920/
__________________
Jon Maddux
14 S1000R | 09 F650GS | 08 M3 Sedan | 06 M Coupe | 01 M coupe
Appreciate 0
Post Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 10:15 PM.




m3post
Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST