BMW M3 Forum (E90 E92)

BMW Garage BMW Meets Register Search Today's Posts Mark Forums Read


Go Back   M3Post - BMW M3 Forum > E90/E92 M3 Technical Topics > DIY Guides/ Discussions
 
PYSPEED
Post Reply
 
Thread Tools Search this Thread
      10-06-2013, 05:45 AM   #1
cantonknees
Enlisted Member
0
Rep
46
Posts

 
Drives: 2008 e92
Join Date: Jul 2013
Location: West Coast

iTrader: (3)

CiC retrofit - repinning fail

hopefully this is the right sub-forum for this thread. here goes...

so I bought a retrofit kit a few weeks back and finally had the time to sit down and attempt the install. during the install, one of the steps required re-pinning four wires from the power cable from the original display to fit the new display's connector.

three of the wires came out as expected and then the last one just would not slide out and after some fiddling, it broke. here is a pic of what I'm talking about:

http://www.realoem.com/bmw/diagrams/m/d/190.png

its either 1, 3, or 5...not exactly sure which one it is that was on that power plug wire that I broke.

since the part is clearly a replaceable part that I can order, I have two questions.

1) how do I pinch or crimp the thing on the wire once I order this replacement part?

2) when I tried inserting the three wires that slid out easily into the new connector, it wouldn't fit. I also noticed the new connector I received has 8 slots vs 6 slots in the connector pictured in the walkthrough I am using. this connector fits in the display I received though so i'm not too concerned, but my old wires not fitting in this new connector does concern me. any ideas there?

I have an 08 e92 m3 btw. thanks for any guidance or advice!
Appreciate 0
      10-06-2013, 08:22 AM   #2
cn555ic
Bimmerscoding.com
cn555ic's Avatar
United_States
246
Rep
18,287
Posts

 
Drives: Bimmerscoding.com
Join Date: Jun 2007
Location: New York

iTrader: (5)

Send a message via Yahoo to cn555ic
the wires should look like this. THe connector to the CID for CIC retrofit screen is a 8 pin connector which is correct...If the wires you extracted doesn't fit correctly into the new connector, you probably have the wire turned upside down or inserted them sideways, retry with wire facing up or the other direction as it should go in only one way nice and smoothly as you will here a noticeable click when pushed all the way in
Attached Images
  

Last edited by cn555ic; 10-06-2013 at 08:36 AM.
Appreciate 0
      10-06-2013, 02:28 PM   #3
cantonknees
Enlisted Member
0
Rep
46
Posts

 
Drives: 2008 e92
Join Date: Jul 2013
Location: West Coast

iTrader: (3)

thanks cn555ic! that's a relief. I guess I was a tard and i'll try again but first I have to figure out the broken pin issue. any thoughts on that part?
Appreciate 0
      01-20-2014, 10:35 PM   #4
rdwest
Enlisted Member
rdwest's Avatar
Canada
1
Rep
46
Posts

 
Drives: 2008 Silverstone E92 M3
Join Date: Aug 2009
Location: Courtenay,BC

iTrader: (0)

Quote:
Originally Posted by cn555ic View Post
the wires should look like this. THe connector to the CID for CIC retrofit screen is a 8 pin connector which is correct...If the wires you extracted doesn't fit correctly into the new connector, you probably have the wire turned upside down or inserted them sideways, retry with wire facing up or the other direction as it should go in only one way nice and smoothly as you will here a noticeable click when pushed all the way in
Strange, funny whatever you'd like to call it. I had the same issue with the brown #3 wire pin. I broke.

The part number I was given is Part #61136954526.

Does this sound familiar? I can get it locally I'm hoping. How did you splice the two pieces. I have been told the been is a solder splice.
__________________
6 Speed Silverstone 2008 E92, Akrapovic exhaust, Dinan intake and ECU, Vorsteiner Diffuser, CIC Upgrade. Smiling all the way
Appreciate 0
      01-21-2014, 01:53 AM   #5
Mike Benvo
BimmerPost Supporting Vendor
Mike Benvo's Avatar
United_States
98
Rep
4,813
Posts


 
Drives: Harrop SC M3 / E46 M3 / 7Turbo
Join Date: Apr 2008
Location: SoCal

iTrader: (7)

Garage List
2008 BMW M3  [5.00]
1990 BMW 735i Turbo  [5.00]
2004 BMW M3  [0.00]
Send a message via Skype™ to Mike Benvo
We have the pins in stock if you need them. Best thing to do is to cut the wire and solder a new wire on with a factory crimp job, otherwise one wire will be slightly shorter.
__________________

-----| Like us on Facebook | Instagram || Tuning Information | Remote Coding |-----
----Visit us at www.BPMSport.com - Emotion. Driven. | Toll Free: (888) 557-5133----
Appreciate 0
      01-21-2014, 09:44 AM   #6
rdwest
Enlisted Member
rdwest's Avatar
Canada
1
Rep
46
Posts

 
Drives: 2008 Silverstone E92 M3
Join Date: Aug 2009
Location: Courtenay,BC

iTrader: (0)

Quote:
Originally Posted by Mike Benvo View Post
We have the pins in stock if you need them. Best thing to do is to cut the wire and solder a new wire on with a factory crimp job, otherwise one wire will be slightly shorter.
Is this part number correct? I was thinking of using a solder crimp using a heat gun to close it.

What is the cost for the wire.

Thanks
__________________
6 Speed Silverstone 2008 E92, Akrapovic exhaust, Dinan intake and ECU, Vorsteiner Diffuser, CIC Upgrade. Smiling all the way
Appreciate 0
      01-21-2014, 07:57 PM   #7
rdwest
Enlisted Member
rdwest's Avatar
Canada
1
Rep
46
Posts

 
Drives: 2008 Silverstone E92 M3
Join Date: Aug 2009
Location: Courtenay,BC

iTrader: (0)

Quote:
Originally Posted by Mike Benvo View Post
We have the pins in stock if you need them. Best thing to do is to cut the wire and solder a new wire on with a factory crimp job, otherwise one wire will be slightly shorter.
Also, you've heard of the hindsight is 20/20 thing. Well, IMO the center console trim should also be removed. I didn't and now due to the extremely tight fit, have damaged the trim. Now I'm looking to replace the black alacantra leather trim piece only. Surprise, I have all the pieces.

Any idea where I can track one down and the cost
__________________
6 Speed Silverstone 2008 E92, Akrapovic exhaust, Dinan intake and ECU, Vorsteiner Diffuser, CIC Upgrade. Smiling all the way
Appreciate 0
      01-23-2014, 07:35 PM   #8
Mike Benvo
BimmerPost Supporting Vendor
Mike Benvo's Avatar
United_States
98
Rep
4,813
Posts


 
Drives: Harrop SC M3 / E46 M3 / 7Turbo
Join Date: Apr 2008
Location: SoCal

iTrader: (7)

Garage List
2008 BMW M3  [5.00]
1990 BMW 735i Turbo  [5.00]
2004 BMW M3  [0.00]
Send a message via Skype™ to Mike Benvo
Can't post pricing here, please PM. Thanks!
__________________

-----| Like us on Facebook | Instagram || Tuning Information | Remote Coding |-----
----Visit us at www.BPMSport.com - Emotion. Driven. | Toll Free: (888) 557-5133----
Appreciate 0
      02-02-2014, 04:54 PM   #9
rdwest
Enlisted Member
rdwest's Avatar
Canada
1
Rep
46
Posts

 
Drives: 2008 Silverstone E92 M3
Join Date: Aug 2009
Location: Courtenay,BC

iTrader: (0)

Quote:
Originally Posted by Mike Benvo View Post
Can't post pricing here, please PM. Thanks!
No worries. I've been able to finish the connection. All is good with the wires I was able to find.

Thanks.
__________________
6 Speed Silverstone 2008 E92, Akrapovic exhaust, Dinan intake and ECU, Vorsteiner Diffuser, CIC Upgrade. Smiling all the way
Appreciate 0
Post Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 08:20 PM.




m3post
Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST