BMW M3 Forum (E90 E92)

BMW Garage BMW Meets Register Search Today's Posts Mark Forums Read


Go Back   M3Post - BMW M3 Forum > E90/E92 M3 Technical Topics > DIY Guides/ Discussions
 
PYSPEED
Post Reply
 
Thread Tools Search this Thread
      07-14-2013, 12:43 PM   #89
W Cole
Captain
 
Drives: 2009 M3
Join Date: Dec 2010
Location: Newport Coast, CA

Posts: 688
iTrader: (4)

FYI to anyone else doing the swap. Bolt #1 on the rear suspension (see photo in post above) does not need to be removed. Just put two wheel lugs into the hub and use your leg or a buddy to put some downward pressure on the suspension and you should be able to get the spring out, the shorter OEM spring should go in even easier.

This bolt is a bit of a pain to line up correctly and its very easy to damage the lower control arm ball joint/bushing when re-installing so its probably best not to remove if you don't have to.

When re-tightening bolt #2.. Before starting the install measure from the center of the hub to fender at normal ride height and then mimic this measurement using a hydraulic jack to compress the suspension when tightening to avoid any undue stress on the bushing.
W Cole is offline  
0
Reply With Quote
      10-07-2013, 07:48 PM   #90
jawwadh
Addicted to Speed.
 
jawwadh's Avatar
 
Drives: 08 e90 m3, 08 tl-S, 13 328xi
Join Date: Aug 2011
Location: Chicago.

Posts: 671
iTrader: (4)

How many people bought new nuts and bolts while doing the spring installed? Is there a part number list? It seems like numerous people have asked but there has been no answer. thanks!
__________________


08 JZB e90 M3 6MT- Dinan/kn/IND/BMWP
13 AW 328xi Msport 8AT
jawwadh is offline   United_States
0
Reply With Quote
      10-07-2013, 09:46 PM   #91
GregW / Oregon
Commander-In-Chief
 
Drives: 2008 M3 Coupe, 2012 ML350
Join Date: Nov 2005
Location: Lake Oswego, OR

Posts: 7,256
iTrader: (1)

Garage List
Quote:
Originally Posted by jawwadh View Post
How many people bought new nuts and bolts while doing the spring installed? Is there a part number list? It seems like numerous people have asked but there has been no answer. thanks!
Does this help?
Attached Images
 
__________________

Greg Lake Oswego, Oregon, USA
2008 M3 Coupe - Alpine/Fox Red/Carbon
2015 M4 coupe on order
GregW / Oregon is offline   United_States
0
Reply With Quote
      11-17-2013, 05:19 PM   #92
J5isalive
Private
 
Drives: M3 Coupe
Join Date: Aug 2010
Location: Alpharetta Ga

Posts: 99
iTrader: (0)

Quote:
Originally Posted by W Cole View Post
FYI to anyone else doing the swap. Bolt #1 on the rear suspension (see photo in post above) does not need to be removed. Just put two wheel lugs into the hub and use your leg or a buddy to put some downward pressure on the suspension and you should be able to get the spring out, the shorter OEM spring should go in even easier.

This bolt is a bit of a pain to line up correctly and its very easy to damage the lower control arm ball joint/bushing when re-installing so its probably best not to remove if you don't have to.

When re-tightening bolt #2.. Before starting the install measure from the center of the hub to fender at normal ride height and then mimic this measurement using a hydraulic jack to compress the suspension when tightening to avoid any undue stress on the bushing.
I tried this method of not removing the bolt, I could not get it to work. I even broke out a small jack and jacked the suspension down to try to get the spring out, no go.

In the end I removed the bolt. 1 side took me 5 minutes to get the bolt back in. The other side took an hour!!!! That bolt is a huge pain, very easy to damage the ball joint.

The front is a breeze.
J5isalive is offline  
0
Reply With Quote
      02-25-2014, 11:09 PM   #93
SR-71
Private First Class
 
SR-71's Avatar
 
Drives: 08 Jerez Black M3
Join Date: Mar 2011
Location: Newport News, VA

Posts: 127
iTrader: (5)

Has anyone had issues with their headlights adjusting too high after installation? Is there a way to reset the headlight sensors? Thanks for the help.
SR-71 is offline   United_States
0
Reply With Quote
      02-25-2014, 11:55 PM   #94
W Cole
Captain
 
Drives: 2009 M3
Join Date: Dec 2010
Location: Newport Coast, CA

Posts: 688
iTrader: (4)

Quote:
Originally Posted by SR-71 View Post
Has anyone had issues with their headlights adjusting too high after installation? Is there a way to reset the headlight sensors? Thanks for the help.
You most likely did not get the headlight leveling sensors oriented correctly when you reinstalled. If you search there is a thread explaining how to correct this.

With that being said, despite correctly reinstalling the headlight leveling sensors my headlights aimed too low after installing my coilovers. There is a knob on each headlight that you turn in order to adjust the height.
W Cole is offline  
0
Reply With Quote
      02-27-2014, 05:58 PM   #95
SR-71
Private First Class
 
SR-71's Avatar
 
Drives: 08 Jerez Black M3
Join Date: Mar 2011
Location: Newport News, VA

Posts: 127
iTrader: (5)

I figured I had somehow messed up the rear level sensor. I just wanted to do some searching/asking for help before getting crazy. Thanks for your help W Cole.
SR-71 is offline   United_States
0
Reply With Quote
      04-18-2014, 02:26 PM   #96
tmntmn
Lieutenant Colonel
 
Drives: e92 M3/M-DCT
Join Date: Feb 2008
Location: Bay Area

Posts: 1,886
iTrader: (6)

Does anyone know the Wrench socket size of the TOP HAT NUT?

thinking about making a tool like a fellow forum member robc1976 did in this picture
__________________
THANKS TO:~<RPM>~ ~<SONICMS>~ ~<MODECARBON>~ ~<McKennaPerformance>~
MODS: MODECARBON V2 GTS FRONT LIP & REAR DIFFUSER, AA GREEN FILTER, RPI SCOOPS, PSW, Verstraβe Extended DCT Shifter, ZCP WHEELS (SEMI-GLOSS), OHLINS R&T, Megan Exhaust, ACM TP, BMW LED INTERIOR, BLACKOUT W/ORION V4 LED AE, OSRAM CBI
tmntmn is offline   United_States
0
Reply With Quote
      04-18-2014, 02:39 PM   #97
adc
Brigadier General
 
Drives: 2009 E90 M3 ED
Join Date: Sep 2006
Location: MD/DC

Posts: 4,073
iTrader: (6)

Quote:
Originally Posted by tmntmn View Post
Does anyone know the Wrench socket size of the TOP HAT NUT?

thinking about making a tool like a fellow forum member robc1976 did in this picture
This tool has a cutout and might work.

http://www.zorotools.com/g/00141033/...FQ2hOgoda2oAJw

Edit: I think the nut is actually 22mm. I used a plumbers adjustable wrench at the time, but will try to source or fabricate a tool when I change springs next month.
__________________

2009 E90 M3 ED
2014 X1 28i
2000 Boxster

Last edited by adc; 04-18-2014 at 02:56 PM.
adc is offline  
0
Reply With Quote
      04-18-2014, 03:18 PM   #98
tmntmn
Lieutenant Colonel
 
Drives: e92 M3/M-DCT
Join Date: Feb 2008
Location: Bay Area

Posts: 1,886
iTrader: (6)

Quote:
Originally Posted by adc View Post
This tool has a cutout and might work.

http://www.zorotools.com/g/00141033/...FQ2hOgoda2oAJw

Edit: I think the nut is actually 22mm. I used a plumbers adjustable wrench at the time, but will try to source or fabricate a tool when I change springs next month.
Thanks!

I'm planning on picking up a cheap socket to cut open
__________________
THANKS TO:~<RPM>~ ~<SONICMS>~ ~<MODECARBON>~ ~<McKennaPerformance>~
MODS: MODECARBON V2 GTS FRONT LIP & REAR DIFFUSER, AA GREEN FILTER, RPI SCOOPS, PSW, Verstraβe Extended DCT Shifter, ZCP WHEELS (SEMI-GLOSS), OHLINS R&T, Megan Exhaust, ACM TP, BMW LED INTERIOR, BLACKOUT W/ORION V4 LED AE, OSRAM CBI
tmntmn is offline   United_States
0
Reply With Quote
      04-18-2014, 03:49 PM   #99
adc
Brigadier General
 
Drives: 2009 E90 M3 ED
Join Date: Sep 2006
Location: MD/DC

Posts: 4,073
iTrader: (6)

Quote:
Originally Posted by tmntmn View Post
Thanks!

I'm planning on picking up a cheap socket to cut open
I just ordered a 22mm oxygen sensor offset socket, which looks like it might do the trick. $9 on amazon. I'll post back here after I receive it.
__________________

2009 E90 M3 ED
2014 X1 28i
2000 Boxster
adc is offline  
0
Reply With Quote
      04-18-2014, 06:36 PM   #100
tmntmn
Lieutenant Colonel
 
Drives: e92 M3/M-DCT
Join Date: Feb 2008
Location: Bay Area

Posts: 1,886
iTrader: (6)

Quote:
Originally Posted by adc View Post
I just ordered a 22mm oxygen sensor offset socket, which looks like it might do the trick. $9 on amazon. I'll post back here after I receive it.
sounds good! please keep me updated!
__________________
THANKS TO:~<RPM>~ ~<SONICMS>~ ~<MODECARBON>~ ~<McKennaPerformance>~
MODS: MODECARBON V2 GTS FRONT LIP & REAR DIFFUSER, AA GREEN FILTER, RPI SCOOPS, PSW, Verstraβe Extended DCT Shifter, ZCP WHEELS (SEMI-GLOSS), OHLINS R&T, Megan Exhaust, ACM TP, BMW LED INTERIOR, BLACKOUT W/ORION V4 LED AE, OSRAM CBI
tmntmn is offline   United_States
0
Reply With Quote
      04-19-2014, 07:30 PM   #101
adc
Brigadier General
 
Drives: 2009 E90 M3 ED
Join Date: Sep 2006
Location: MD/DC

Posts: 4,073
iTrader: (6)

Quote:
Originally Posted by tmntmn View Post
sounds good! please keep me updated!
Just found this: http://www.ecstuning.com/News/Schwab...Kit/ES2652183/
__________________

2009 E90 M3 ED
2014 X1 28i
2000 Boxster
adc is offline  
0
Reply With Quote
      05-09-2014, 12:00 AM   #102
apecush
Lieutenant
 
Drives: 2008 E90 M3
Join Date: Aug 2011
Location: Edmonton

Posts: 430
iTrader: (2)

Just wanted to say thanks for the DIY. Did my springs, camber plates, and rear dinan mounts over two evenings, a grand total of about 5 hours (not working particularly fast). I think I spent more time finding the right size socket or wrench than actually working. This car has every metric size under the sun! I'm used to working on Japanese cars, where everything is 10, 12, 14, 17, 19, or 21mm.

FYI, on my car, 08 w/edc, the front strut nuts were 21mm.
apecush is offline  
0
Reply With Quote
      06-28-2014, 03:27 PM   #103
adc
Brigadier General
 
Drives: 2009 E90 M3 ED
Join Date: Sep 2006
Location: MD/DC

Posts: 4,073
iTrader: (6)

I just did the rears on my car, took around 2.5 hours with a second pair of hands helping. I found it easier to use 3 jacks: one to raise the car, one to raise/lower the suspension arm as needed, and the third to raise or lower the disc brake (suspension hub) as needed.

The difficulty came from the fact that you need to adjust the last bolt in 2 directions, left right and up down. So while I could get enough leverage with a wrench, I couldn't maintain the support long enough to line the holes correctly.

With the 3 jacks in place, all I needed was a big old screwdriver to position the holes.

Just did the fronts, took again about 2-2.5 hours. I used this tool: http://www.ecstuning.com/News/Schwab...Kit/ES2652181/
21mm for my 2009 with EDC.

Didn't get an EDC fault, but I think I messed up a brake sensor because i got the yellow car-on-the-list symbol and I noticed one of them hanging at the front. I'll check it next week when I do track pads.
__________________

2009 E90 M3 ED
2014 X1 28i
2000 Boxster

Last edited by adc; 06-29-2014 at 11:08 AM.
adc is offline  
0
Reply With Quote
Post Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 08:28 PM.




m3post
Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST