Vorshlag Camber Plates for M3

1MOREMOD · 08-03-2013, 10:52 AM

Quote:

Originally Posted by gan1hck

I know this post is a little old, but I just had these plates installed in my car....and I'm wondering how you get the edc cap to fit when you adjust the camber to max negative setting?????

you dont. there has to be some room left. it can be pretty close and you can work it onto there however.

gan1hck · 08-03-2013, 11:18 AM

Quote:

Originally Posted by 1MOREMOD

you dont. there has to be some room left. it can be pretty close and you can work it onto there however.

I tried for half an hour trying to fit the cap back on....gave up and just cut the cap off and left the wires exposed.

Glad I tried this out before track....would have hated wasting time at track side trying to figure this out.

1MOREMOD · 08-03-2013, 12:34 PM

Quote:

Originally Posted by gan1hck

I tried for half an hour trying to fit the cap back on....gave up and just cut the cap off and left the wires exposed.

Glad I tried this out before track....would have hated wasting time at track side trying to figure this out.

you removed the cap not cut the wires correct? how much camber are you running i had -2.5 and fit the cap still. thats about tops for street driven car really.

gan1hck · 08-03-2013, 01:03 PM

Quote:

Originally Posted by 1MOREMOD

you removed the cap not cut the wires correct? how much camber are you running i had -2.5 and fit the cap still. thats about tops for street driven car really.

removed the cap, so that the wiring would fit and keep edc functional.

-2.5 is all that I can get with the plates pushed all the way in with the center of the strut touching the inside of the metal cutout.......-1.5 in street/factory setting.

1MOREMOD · 08-03-2013, 01:23 PM

Quote:

Originally Posted by gan1hck

removed the cap, so that the wiring would fit and keep edc functional.

-2.5 is all that I can get with the plates pushed all the way in with the center of the strut touching the inside of the metal cutout.......-1.5 in street/factory setting.

okay i was able to get closer to -3 with stock ride height but at -2.5 i could fit the cap.

HP Autosport · 08-04-2013, 10:31 PM

These are once again on back order until mid to late August.

ortho281 · 08-06-2013, 12:40 PM

Quote:

Originally Posted by gan1hck

I know this post is a little old, but I just had these plates installed in my car....and I'm wondering how you get the edc cap to fit when you adjust the camber to max negative setting?????

I have never adjusted camber to max, but I can see how this would be a problem. I believe you can go up to -3.0 neg (lowered) without any problems. On a E92, you should not be needing more than -2.8 neg.

gan1hck · 08-06-2013, 01:20 PM

Quote:

Originally Posted by ortho281

I have never adjusted camber to max, but I can see how this would be a problem. I believe you can go up to -3.0 neg (lowered) without any problems. On a E92, you should not be needing more than -2.8 neg.

the max is -2.5 for me

ortho281 · 08-06-2013, 04:41 PM

Quote:

Originally Posted by gan1hck

the max is -2.5 for me

I see. It depends on how much you are lowered. The more you lower the front end, the less neg camber you need to adj with the camber plates. I'm lowered about 1 inch with KW S/O, so don't need as much adj with plates.

gan1hck · 08-06-2013, 04:48 PM

Quote:

Originally Posted by ortho281

I see. It depends on how much you are lowered. The more you lower the front end, the less neg camber you need to adj with the camber plates. I'm lowered about 1 inch with KW S/O, so don't need as much adj with plates.

that's what I figured....I'm at stock height.

Got rid of the caps, and everything is all good again.

ortho281 · 08-06-2013, 08:09 PM

Quote:

Originally Posted by gan1hck

that's what I figured....I'm at stock height.

Got rid of the caps, and everything is all good again.

That would explain why you are close to max neg. and why your caps are not fitting.

HP Autosport · 08-19-2013, 06:05 PM

Have a very limited number of Vorshlag camber plates for the E9x M3 ready to ship! PM, email or call us before placing your order!

HP Autosport · 10-04-2013, 11:37 PM

Looks like all the back orders will be filled in about two weeks! There should be plenty of spaces for new orders as well!

1MOREMOD · 10-04-2013, 11:39 PM

Quote:

Originally Posted by HP Autosport

Looks like all the back orders will be filled in about two weeks! There should be plenty of spaces for new orders as well!

Late night sales. Harolds always on it!

HP Autosport · 10-15-2013, 05:41 PM

These are shipping in the next few days!

We will have about 10 sets of these after filling all back orders so order away!

HP Autosport · 10-22-2013, 12:42 PM

About 10 sets just arrived!

HP Autosport · 10-25-2013, 02:27 PM

Vorshlag is back ordered again on the 1M/M3 camber plates. We still have a few on the shelf after filling all the back orders.

HP Autosport · 11-04-2013, 09:43 PM

Have just a couple of sets left!

mlhj83 · 12-03-2013, 09:23 AM

Are the OEM springs more compressed with the Vorshlag spring perch compared to the OEM mounts, or are the springs of equal height? Thanks.

HP Autosport · 01-15-2014, 03:53 PM

Quote:

Originally Posted by mlhj83

Are the OEM springs more compressed with the Vorshlag spring perch compared to the OEM mounts, or are the springs of equal height? Thanks.

No, the stack height of the camber plates are exactly like th OE strut mounts. Your ride height is not changed with the installation of these.

yandy · 01-28-2014, 06:04 PM

are the OE strut type/sport-springs in stock? can't find anyone with stock ready to ship.

Foozed · 03-05-2014, 01:00 PM

Quote:

Originally Posted by HP Autosport

No, the stack height of the camber plates are exactly like th OE strut mounts. Your ride height is not changed with the installation of these.

Just installed mine yesterday and there is a very noticeable increase in rode height. So much so that I'll be shopping for springs now

08-04-2013, 10:31 PM	#116
HP Autosport BimmerPost Supporting Vendor 448 Rep 11,499 Posts Drives: F80 M3 Join Date: Mar 2007 Location: Santa Barbara, Brembo, GIAC, Koni, Ohlins, Performance Friction, Quaife, Stoptech, Vorshlag iTrader: (31)	These are once again on back order until mid to late August.
	Appreciate 0 Quote

08-19-2013, 06:05 PM	#122
HP Autosport BimmerPost Supporting Vendor 448 Rep 11,499 Posts Drives: F80 M3 Join Date: Mar 2007 Location: Santa Barbara, Brembo, GIAC, Koni, Ohlins, Performance Friction, Quaife, Stoptech, Vorshlag iTrader: (31)	Have a very limited number of Vorshlag camber plates for the E9x M3 ready to ship! PM, email or call us before placing your order!
	Appreciate 0 Quote

10-04-2013, 11:37 PM	#123
HP Autosport BimmerPost Supporting Vendor 448 Rep 11,499 Posts Drives: F80 M3 Join Date: Mar 2007 Location: Santa Barbara, Brembo, GIAC, Koni, Ohlins, Performance Friction, Quaife, Stoptech, Vorshlag iTrader: (31)	Looks like all the back orders will be filled in about two weeks! There should be plenty of spaces for new orders as well!
	Appreciate 0 Quote

10-15-2013, 05:41 PM	#125
HP Autosport BimmerPost Supporting Vendor 448 Rep 11,499 Posts Drives: F80 M3 Join Date: Mar 2007 Location: Santa Barbara, Brembo, GIAC, Koni, Ohlins, Performance Friction, Quaife, Stoptech, Vorshlag iTrader: (31)	These are shipping in the next few days! We will have about 10 sets of these after filling all back orders so order away!
	Appreciate 0 Quote

10-22-2013, 12:42 PM	#126
HP Autosport BimmerPost Supporting Vendor 448 Rep 11,499 Posts Drives: F80 M3 Join Date: Mar 2007 Location: Santa Barbara, Brembo, GIAC, Koni, Ohlins, Performance Friction, Quaife, Stoptech, Vorshlag iTrader: (31)	About 10 sets just arrived! Attached Images
	Appreciate 0 Quote

10-25-2013, 02:27 PM	#127
HP Autosport BimmerPost Supporting Vendor 448 Rep 11,499 Posts Drives: F80 M3 Join Date: Mar 2007 Location: Santa Barbara, Brembo, GIAC, Koni, Ohlins, Performance Friction, Quaife, Stoptech, Vorshlag iTrader: (31)	Vorshlag is back ordered again on the 1M/M3 camber plates. We still have a few on the shelf after filling all the back orders.
	Appreciate 0 Quote

11-04-2013, 09:43 PM	#128
HP Autosport BimmerPost Supporting Vendor 448 Rep 11,499 Posts Drives: F80 M3 Join Date: Mar 2007 Location: Santa Barbara, Brembo, GIAC, Koni, Ohlins, Performance Friction, Quaife, Stoptech, Vorshlag iTrader: (31)	Have just a couple of sets left!
	Appreciate 0 Quote

12-03-2013, 09:23 AM	#129
mlhj83 Scythe-Meister 24 Rep 1,041 Posts Drives: '11 E92 M3 DCT ZCP Join Date: Aug 2011 Location: London iTrader: (0)	Are the OEM springs more compressed with the Vorshlag spring perch compared to the OEM mounts, or are the springs of equal height? Thanks.
	Appreciate 0 Quote

01-28-2014, 06:04 PM	#131
yandy Lieutenant Colonel 32 Rep 1,968 Posts Drives: 2009 e92 MR "Civic" ///M3 Join Date: Feb 2009 Location: Miami, FL iTrader: (3) Garage List 2009 BMW M3 [0.00]	are the OE strut type/sport-springs in stock? can't find anyone with stock ready to ship. __________________ \|\| DCT \| ESS Tune \| ACM Test-pipes \| AA Green Filter \| Swift Spec-R Springs \| Stoptech ST-40 F \|\| \|\| My Youtube Channel\|\| My Vimeo Channel \|\|
	Appreciate 0 Quote

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search