BMW M3 Forum (E90 E92)

BMW Garage BMW Meets Register Search Today's Posts Mark Forums Read


Go Back   M3Post - BMW M3 Forum > E90/E92 M3 Technical Topics > Cosmetic/Visual (Exterior + Interior) Modifications
 
GetBMWParts
Post Reply
 
Thread Tools Search this Thread
      05-03-2011, 08:37 AM   #1
Dieselino
Lieutenant
28

 
Dieselino's Avatar
 
Drives: 03 LSB M3 06 M coupe 08 M3 SG
Join Date: Apr 2007
Location: Detroit


Posts: 592
iTrader: (2)

BMW Carbonfiber Spoiler installation, 3M tape works perfect!

Sorry I didnt not take any pics but there is absolutly no reason if installed properly that 3M double sided automotive tape will not work. I believe many auto stores sell it and even home depot. Its the grey foam tape with the red backing, its no different then the tape used on the OEM M3 lip spoiler.

First off the spoiler weighs nothing, it is alot lighter then the stock spoiler so no serious glueing is required. I wanted to be able to remove the spoiler later if I needed to, and using betalink would probably be very difficult to remove without damaging the spoiler.

Anyways on to the install, remove the stock spoiler with fishing line. Once its off heat up the residual tape thats left with a heat gun and it should come off with a little work. I then used a wax and grease remover on the spoiler and the trunk to make sure the tape would stick on a clean surface for maximum contact.

As for the tape, I used a fine exacto knife and cut strips of tape to the appropriate width and put it around the entire edge of the spoiler. I didnt put it right on the edge of the spoiler, more like a 2 or 3mm away from the edge so when the spoiler is put down the tape isnt visible.

Once all done tape I test fitted the spoiler so I would know where to place it because once the tape sticks it will be very hard to remove without messing up the tape. To make things easier, once I had the spoiler all lined up I used some masking tape and tape areas around the spoiler as a guide so I could line up the spoiler in one shot.

I then peeled all the red backing off the tape and then heated up both the decklid and the spoiler with the heat gun so the tape would be tacky and be sticking to a warm clean surface for maximum intial adhesion.

I then placed the spoiler on using the masking tape I put down earlier as a guide and pressed the spoiler down good when I checked everything. the spoiler is on really good and is not going anywhere. Save yourselfs the messy headache of using glue and just use the tape. If you take your time and do it right it works perfect. That tape is used in many OEM applications and has been used for years and it holds on much heavier parts that take more abuse then an extremely light carbonfiber spoiler.
Appreciate 0
      05-03-2011, 09:20 AM   #2
UsurbrainM3
Private First Class
4

 
Drives: 2008 e90 M3
Join Date: Jan 2011
Location: CA


Posts: 132
iTrader: (0)

Appreciate 0
      05-03-2011, 11:16 AM   #3
Dieselino
Lieutenant
28

 
Dieselino's Avatar
 
Drives: 03 LSB M3 06 M coupe 08 M3 SG
Join Date: Apr 2007
Location: Detroit


Posts: 592
iTrader: (2)

Yes I know... didnt have time to take pics during the install
Appreciate 0
      05-04-2011, 10:45 AM   #4
Jbook
Major
33

 
Jbook's Avatar
 
Drives: '11 ESS E90 M3
Join Date: Sep 2010
Location: South Bay Area


Posts: 1,290
iTrader: (20)

Garage List
2011 BMW E90 M3  [4.72]
I just installed the type II CF performance spoiler on my e90 yesterday only using 3M tape. Worked perfectly and definitely will not fly off (even if you go 100+). I don't understand why everyone thinks you need to use permanent betalink.

I didn't even use a heat gun or anything. I just lined the spoiler with 3M a bit back from the edge, lined it up with the trunk, and stuck it on. No tape is visible.
Appreciate 0
      06-19-2013, 08:53 AM   #5
jtuds
Major
Canada
39

 
Drives: 335i M Sport
Join Date: Oct 2011
Location: 1.5-2 hrs west of Toronto


Posts: 1,064
iTrader: (0)

Everyone's spoilers still attached?
Appreciate 0
      06-19-2013, 09:21 AM   #6
Alex@ONEighty
BimmerPost Supporting Vendor
United_States
68


 
Alex@ONEighty's Avatar
 
Drives: E93 M3
Join Date: Jul 2012
Location: NYC


Posts: 592
iTrader: (3)

3M Double sided tap is super strong and we use it for lips and smaller spoilers all the time. As long as the area where the spoiler is being applied is properly cleaned it should hold up very well.
Appreciate 0
      06-19-2013, 10:54 AM   #7
edwinm3
Lieutenant Colonel
United_States
34

 
edwinm3's Avatar
 
Drives: E92 MELBOURNE RED M3
Join Date: Nov 2011
Location: Doral


Posts: 1,915
iTrader: (8)

I just can't live with the fact that it doesn't matter how thin the tape is you can always see a slight gap. And I'm not new to this. I use tape on the splitters and the diffuser but not on the spoiler. What I do is grab a medical syringe cut the plastic tip off and use it to lay the glue nice and thin. Once you press on it it'll spread and practically no or very little comes out. Comes out great.

Just removed one I applied to my E90 using my technique and came off pretty easy with a string, sawing thru the betalink.
FYI betalink doesn't get rock solid it turns into a hard rubber when dry
__________________
Appreciate 0
      06-19-2013, 03:46 PM   #8
M3PO
Colonel
45

 
M3PO's Avatar
 
Drives: '08 IB E92
Join Date: Sep 2011
Location: OC


Posts: 2,753
iTrader: (7)

Quote:
Originally Posted by edwinm3 View Post
I just can't live with the fact that it doesn't matter how thin the tape is you can always see a slight gap. And I'm not new to this. I use tape on the splitters and the diffuser but not on the spoiler. What I do is grab a medical syringe cut the plastic tip off and use it to lay the glue nice and thin. Once you press on it it'll spread and practically no or very little comes out. Comes out great.

Just removed one I applied to my E90 using my technique and came off pretty easy with a string, sawing thru the betalink.
FYI betalink doesn't get rock solid it turns into a hard rubber when dry
My spoiler has virtually no gap at all. To the point where you can't see the tape at all. Usually this bothers me also, but it's not an issue at all with the Performance spoiler. It has a little lip that hides the tape (or a recess where the tape sits, I forget).
__________________
2008 IB E92 M3| BBS | KW | Arkym | Platte Forme A.G. | Active Autowerke | K&N | Fabspeed | Dinan | Evolve-R
Appreciate 0
      06-20-2013, 12:54 PM   #9
edwinm3
Lieutenant Colonel
United_States
34

 
edwinm3's Avatar
 
Drives: E92 MELBOURNE RED M3
Join Date: Nov 2011
Location: Doral


Posts: 1,915
iTrader: (8)

Just don't see why ppl are so afraid of using betalink
__________________
Appreciate 0
      06-20-2013, 10:53 PM   #10
W Cole
Captain
27

 
Drives: 2009 M3
Join Date: Dec 2010
Location: Newport Coast, CA


Posts: 764
iTrader: (4)

If you want an even stronger tape get some 3M VHB tape for painted surfaces off of amazon.
Appreciate 0
Post Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 09:00 PM.




m3post
Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST