Login


11272012, 11:22 PM  #89 
Lieutenant General
236
Rep 10,257
Posts 
Rogue said explicitly that with both of their systems, 1 and 2 pulleys, that all systems are underdriven by the same 16% figure. The point of the 2nd pulley in the 2 pulley system (included in a note in the spreadsheet) is to be able to use readily accessible belts (as pointed out also in a post just above).
Last edited by swamp2; 11282012 at 01:55 AM. 
Appreciate
0

11282012, 05:14 PM  #90 
Colonel
54
Rep 2,717
Posts 
The AFE is 4.124" in diameter, according to my calculations this makes it a 84.5 of the OEM diameter or a 15.5% reduction if my calculations are correct.
Dave
__________________
2013 M3 CoupeMR/BLK ZCP, ACM test pipes, BPM Stg2 dev. tune and Megan catback, AFE Stg2. with C/F elbow VMRV810 19x10&19X11 275/295 Mich PSS.
Previous rides: 2011 M3 CoupeMR/Blk 2007 Porsche 997C2S Speed Yellow/Blk sport seats 2004 BMW M3 Imola/Blk 
Appreciate
0

11282012, 09:16 PM  #91 
Lieutenant General
236
Rep 10,257
Posts 
Great, thanks. Does this also mean you measured the OEM pulley at 124mm (4.88"). In the calculations for the AA pulley I used 122mm as the OEM size. I will use these figures for an update.

Appreciate
0

11282012, 09:19 PM  #92 
Lieutenant General
236
Rep 10,257
Posts 

Appreciate
0

11282012, 09:59 PM  #93  
Colonel
54
Rep 2,717
Posts 
Quote:
Swamp I didn't know the exact size of the OEM pulley just what I saw someone else post up. I used 124mm for OEM, if its 122mm then I am off a bit. Dave
__________________
2013 M3 CoupeMR/BLK ZCP, ACM test pipes, BPM Stg2 dev. tune and Megan catback, AFE Stg2. with C/F elbow VMRV810 19x10&19X11 275/295 Mich PSS.
Previous rides: 2011 M3 CoupeMR/Blk 2007 Porsche 997C2S Speed Yellow/Blk sport seats 2004 BMW M3 Imola/Blk 

Appreciate
0

11282012, 10:27 PM  #94 
Lieutenant General
236
Rep 10,257
Posts 
Thanks for clarifying. This means the AA and AFE numbers in the table are still potentially off a percent or two. Anyone with a precise number here?

Appreciate
0

11292012, 12:24 AM  #95 
Colonel
32
Rep 2,315
Posts 
Looking at your sheet swamp, there's a small error on a technicality. The AA pulley is shown as coming with 2 belts when it actually comes with 3. 2 for use with the new crank, and 1 extra belt for the double sided application. I'll try to get an exact measurement tomorrow on my removed stock pulley. I'll post a picture like Andrew did if I can find the time in the evening, using the same style digital caliper.

Appreciate
0

11292012, 02:01 AM  #96  
Lieutenant General
236
Rep 10,257
Posts 
Quote:
Thanks in advance for any measurements you can share. IMHO there is absolutely no need to post a fancy picture like that "proving" a number. If you're a contributing member here and you know how to zero and use a caliper, no one should question a simple distance measurement on a small part. Really  don't waste your time. 

Appreciate
0

11302012, 01:05 AM  #98  
Colonel
54
Rep 2,717
Posts 
Quote:
Dave
__________________
2013 M3 CoupeMR/BLK ZCP, ACM test pipes, BPM Stg2 dev. tune and Megan catback, AFE Stg2. with C/F elbow VMRV810 19x10&19X11 275/295 Mich PSS.
Previous rides: 2011 M3 CoupeMR/Blk 2007 Porsche 997C2S Speed Yellow/Blk sport seats 2004 BMW M3 Imola/Blk 

Appreciate
0

12022012, 12:26 PM  #99 
Colonel
50
Rep 2,267
Posts 
Is there any proof that the underdrive on the water pump actually has an effect in high rpm running? Many OEM pumps are on the right side of their envelope once you get within 2000 rpm of redline, underdriving the pump can actually help ontrack cooling on some cars.
__________________

Appreciate
0

12032012, 03:53 AM  #100 
Captain
22
Rep 900
Posts 
I understand cooling may be diminished and depending on the pulley setup you choose the A/C system as well.
But has anyone running these pulleys noticed any power steering lag during quick corrections? I would hate to install a set and then have the power steering not react 100% while quickly correcting unanticipated oversteer, etc. Also, I haven't seen the charging system addressed. All of these pulleys must underdrive the alternator as well? I know the M3 charge system is already very weak.. just spent $500 on a new battery. 
Appreciate
0

12032012, 12:45 PM  #101  
Lieutenant
16
Rep 561
Posts 
Quote:


Appreciate
0

12032012, 03:09 PM  #102 
Lieutenant General
236
Rep 10,257
Posts 
Some speculation but I would expect if there was not enough rpm/power/pressure in the PS system that the response would be a heavier feel rather than a lack of response. Due to safety the power steering is almost always a boost on what can be done purely manually.

Appreciate
0

12032012, 09:12 PM  #103  
Colonel
32
Rep 2,315
Posts 
Quote:
Yes you are correct that the AA kit requires 2 special belts, but it does comes with 3. In case you or anyone didn't know that, I thought I would mention it. 

Appreciate
0

12312012, 07:55 AM  #108 
Captain
10
Rep 627
Posts 
I've read that the e9x M cars decouple the alternator under full throttle.
Assuming this is true, the % by which the alternator pulley is underdriven is irrelevant with respect to peak hp gains. 
Appreciate
0

12312012, 05:24 PM  #109 
Banned
8
Rep 220
Posts 
exactly! I always have preached underdrive pulley's no longer are worth it. The A/C and alternator are already disengaged under large throttle which means the only thing that is underdriven is powersteering and engine cooling. The two things I would never want to have heat up more than normal.
In older cars it was more worth it because you had all 4 systems sucking power but in new bimmers, you only have the water pump and power steering sucking power. I hope with newer engines they go with electrical water pump like the N52 engine. That way it would completely eliminate the need for an underdrive pulley. Especially if they go electric steering which they will. Actually may eliminate the need for a accessory drive if they can change how the A/C is run. This would probably free up 1520 hp consistently in cars and save on mileage. That is a winwin and should be the focus for bmw on m cars rather than going turbo. Lighter cars and elimination of parastic losses and direct injection could have netted great mileage on naturally aspirated high revving cars to meet both mileage and enthusiast desires 
Appreciate
0

01062013, 09:32 PM  #110  
Captain
22
Rep 900
Posts 
Quote:
Unfortunately I did not have a pair of calipers large enough to fit around the pulleys. Can anyone from EAS chime in with the measurements? 

Appreciate
0

Post Reply 
Bookmarks 
Thread Tools  Search this Thread 

