BMW M3 Forum (E90 E92)

BMW Garage BMW Meets Register Search Today's Posts Mark Forums Read


Go Back   M3Post - BMW M3 Forum > E90/E92 M3 Technical Topics > Engine, Transmission, Exhaust, Drivetrain, ECU Software Modifications
 
BPM Sport
Post Reply
 
Thread Tools Search this Thread
      11-14-2012, 05:25 PM   #23
Mike Benvo
BimmerPost Supporting Vendor

 
Mike Benvo's Avatar
 
Drives: 08 E90 M3 / 400whp Turbo 7
Join Date: Apr 2008
Location: SoCal

Posts: 4,574
iTrader: (7)

Garage List
1990 BMW 735i Turbo  [5.00]
2004 BMW M3  [0.00]
2008 BMW M3  [5.00]
Send a message via Skype™ to Mike Benvo
Many people have asked me:
1) How long will it take for the light to come on?
2) Why do some cars trigger the light sooner than others?
3) Will my driving style affect how long it takes to trigger the light?

Here are the answers of how setting readiness works. The CEL is thrown after readiness FAILS and may require MULTIPLE drive cycles to ensure that all testing conditions are met:

An example of a drive cycle is as follows:
1. Engine cold start, idling, approximately 3 minutes.

Evaluated:

• Secondary Air System
• Evaporative Leak Detection (LDP Equipped Vehicles)

2. Constant driving at 20 to 30 MPH, approximately 4 minutes.

Evaluated:

• Oxygen Sensors - Achieved “Closed Loop” Operation
• Oxygen Sensors - Response Time and Switching Time (Control Frequency)

3. Constant driving at 40 to 60 MPH, approximately 15 minutes (sufficient vehicle coasting phases included).

Evaluated:

• Catalytic Converter Efficiency
• Oxygen Sensors - Response Time and Switching Time (Control Frequency)

4. Engine idling, approximately 5 minutes.

Evaluated:
Tank-Leak Diagnosis (DMTL Equipped Vehicles after KL 15 is switched OFF) US Spec M3's are DMTL Equipped and KL15 means ignition on.

Now the reason of why some cars take MUCH longer than others to throw the error light - Driving Style!

The diagnostic sequence illustrated above will be interrupted if:
• The engine speed exceeds 3000 RPM.
• Large fluctuations in the accelerator pedal position.
• The driving speed exceeds 60 MPH.


The Service Engine Soon / Increased Emissions! warning will be illuminated under the following conditions:
• Upon the completion of the next consecutive driving cycle where the previously faulted system is monitored again and the emissions relevant
fault is again present.

• Immediately if a “Catalyst Damaging” fault occurs (Misfire Detection).

The illumination of the light is performed in accordance with the Federal Test Procedure (FTP) which requires the lamp to be illuminated when:

• A malfunction of a component that can affect the emission performance of the vehicle occurs and causes emissions to exceed 1.5 times the standards required by the (FTP).
• Manufacturer-defined specifications are exceeded.
• An implausible input signal is generated.
• Catalyst deterioration causes HC-emissions to exceed a limit equivalent to 1.5 times the standard (FTP).
• Misfire faults occur.
• A leak is detected in the evaporative system, or “purging” is defective.
• ECM fails to enter closed-loop oxygen sensor control operation within a specified time interval.
• Engine control or automatic transmission control enters a "limp home" operating mode.
• Ignition is on (KL15) position before cranking = Bulb Check Function.

There you have it. Everything you need to know about readiness testing, how it's tested, and why some cars take longer than others to record an error.

If anyone has any questions, please let me know. I can go further in depth to what the DME is looking for for each specific test if you'd like. I hope this post helps educate anyone interested in how these testing procedures are performed.

__________________

-----| Like us on Facebook | Instagram || Tuning Information | Remote Coding |-----
----Visit us at www.BPMSport.com - Emotion. Driven. | Toll Free: (888) 557-5133----
Mike Benvo is offline   United_States
0
Reply With Quote
      11-15-2012, 01:29 PM   #24
System Of A...
Captain
 
System Of A...'s Avatar
 
Drives: e93 M3
Join Date: Jun 2010
Location: 818

Posts: 846
iTrader: (1)

Garage List
2008 BMW e93 M3  [3.83]
Thanks for the great info mike and tom!
__________________
Gintani 4.6l S65 | Gintani Race Catless Exhaust | Gintani CF Race lip
System Of A... is offline   Armenia
0
Reply With Quote
      12-21-2012, 07:04 PM   #25
andy9188
Lieutenant
 
andy9188's Avatar
 
Drives: van
Join Date: Apr 2012
Location: uk

Posts: 427
iTrader: (4)

Quote:
Originally Posted by tom @ eas View Post
Kiwi/PLX makes an OBDII interface that will interact with your iPhone/Android device via Bluetooth for ~$75.

Clearing codes is only temporary, you'll need a flash tune (like the ESS E-Flash) in order to get this rectified.
How much is the flash tom? Does it come with a cable lime the evolve r cable? I'm in the UK
andy9188 is offline  
0
Reply With Quote
      12-21-2012, 07:09 PM   #26
andy9188
Lieutenant
 
andy9188's Avatar
 
Drives: van
Join Date: Apr 2012
Location: uk

Posts: 427
iTrader: (4)

Quote:
Originally Posted by Mike Benvo View Post
Many people have asked me:
1) How long will it take for the light to come on?
2) Why do some cars trigger the light sooner than others?
3) Will my driving style affect how long it takes to trigger the light?

Here are the answers of how setting readiness works. The CEL is thrown after readiness FAILS and may require MULTIPLE drive cycles to ensure that all testing conditions are met:

An example of a drive cycle is as follows:
1. Engine cold start, idling, approximately 3 minutes.

Evaluated:

• Secondary Air System
• Evaporative Leak Detection (LDP Equipped Vehicles)

2. Constant driving at 20 to 30 MPH, approximately 4 minutes.

Evaluated:

• Oxygen Sensors - Achieved “Closed Loop” Operation
• Oxygen Sensors - Response Time and Switching Time (Control Frequency)

3. Constant driving at 40 to 60 MPH, approximately 15 minutes (sufficient vehicle coasting phases included).

Evaluated:

• Catalytic Converter Efficiency
• Oxygen Sensors - Response Time and Switching Time (Control Frequency)

4. Engine idling, approximately 5 minutes.

Evaluated:
Tank-Leak Diagnosis (DMTL Equipped Vehicles after KL 15 is switched OFF) US Spec M3's are DMTL Equipped and KL15 means ignition on.

Now the reason of why some cars take MUCH longer than others to throw the error light - Driving Style!

The diagnostic sequence illustrated above will be interrupted if:
• The engine speed exceeds 3000 RPM.
• Large fluctuations in the accelerator pedal position.
• The driving speed exceeds 60 MPH.


The Service Engine Soon / Increased Emissions! warning will be illuminated under the following conditions:
• Upon the completion of the next consecutive driving cycle where the previously faulted system is monitored again and the emissions relevant
fault is again present.

• Immediately if a “Catalyst Damaging” fault occurs (Misfire Detection).

The illumination of the light is performed in accordance with the Federal Test Procedure (FTP) which requires the lamp to be illuminated when:

• A malfunction of a component that can affect the emission performance of the vehicle occurs and causes emissions to exceed 1.5 times the standards required by the (FTP).
• Manufacturer-defined specifications are exceeded.
• An implausible input signal is generated.
• Catalyst deterioration causes HC-emissions to exceed a limit equivalent to 1.5 times the standard (FTP).
• Misfire faults occur.
• A leak is detected in the evaporative system, or “purging” is defective.
• ECM fails to enter closed-loop oxygen sensor control operation within a specified time interval.
• Engine control or automatic transmission control enters a "limp home" operating mode.
• Ignition is on (KL15) position before cranking = Bulb Check Function.

There you have it. Everything you need to know about readiness testing, how it's tested, and why some cars take longer than others to record an error.

If anyone has any questions, please let me know. I can go further in depth to what the DME is looking for for each specific test if you'd like. I hope this post helps educate anyone interested in how these testing procedures are performed.

How much is your tune also mike does it come with a cable so I can put back to stock myself? Pm me if you like. I'm in the uk
andy9188 is offline  
0
Reply With Quote
      12-21-2012, 08:22 PM   #27
Vic311
Banned
 
Drives: 2011 e92 M3
Join Date: Dec 2012
Location: NY

Posts: 1,469
iTrader: (0)

Quote:
Originally Posted by tom @ eas View Post
It will come on eventually.
+1..it always does
Vic311 is offline   United_States
0
Reply With Quote
      12-21-2012, 08:27 PM   #28
Chriskm3
Colonel
 
Chriskm3's Avatar
 
Drives: M3
Join Date: Jul 2012
Location: Toronto

Posts: 2,218
iTrader: (4)

It always does
Chriskm3 is offline   Canada
0
Reply With Quote
      12-21-2012, 08:29 PM   #29
Munit
Banned
 
Drives: m3
Join Date: Oct 2012
Location: CA

Posts: 220
iTrader: (0)

I have AA HFC xpipe for 3 months and about 10000 miles and no CEL here. I was waiting for it but never came. Figured after 10k miles it would be here if it was going to happen!
Munit is offline  
0
Reply With Quote
Post Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 08:41 PM.




m3post
Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST