BMW M3 Forum (E90 E92)

BMW Garage BMW Meets Register Search Today's Posts Mark Forums Read


Go Back   M3Post - BMW M3 Forum > E90/E92 M3 Technical Topics > Suspension | Brakes | Chassis
 
PYSPEED
Post Reply
 
Thread Tools Search this Thread
      08-08-2012, 07:01 AM   #1
gsrbri
Enlisted Member
 
Drives: E90 M3
Join Date: Jul 2011
Location: Boston, MA

Posts: 46
iTrader: (0)

Track brake pad/rotor wear - your results?

My 2011 E90 ZCP is a daily driver, but sees quite a few track days. Since I purchased the car in July 2011, I've done 8 days (6 at New Hampshire MS and two at Mt. Tremblant). I run stock pads on the street and Pagid RS-19 yellows front and RS-7 black on the rear when on-track. I'm an intermediate-level driver and get into my brakes very hard each lapping session.

After 8 days, my Pagid pads are still good for probably two more track days (wear has been excellent). The rotors, both front/rear, are exhibiting no "lip" after 13,000 miles of spirited driving on the road and track. The Pagid pads, as it turns out, bed very well at the track w/no real need to pre-bed, and I've installed the factory pads directly after being on track, and, as long as you don't hammer the brakes too much, the stock pads remove the bedded material from the Pagids and wipe the rotor clean. No pedal pulsations or anything.

I had a friend that drives an E90 M3 w/PFC-01 pads drive my car at Mt. Tremblant and his impression was that the PFC's offer a little more bite at the limit, but the Pagids are very good. He is seeing much more wear w/the PFC-01s, both on the pads and rotors.

What are your experiences?

-Brian

Last edited by gsrbri; 08-08-2012 at 07:02 AM. Reason: misspelling subject
gsrbri is offline  
0
Reply With Quote
      08-08-2012, 08:10 AM   #2
Gearhead999s
Major General
 
Gearhead999s's Avatar
 
Drives: E93 335is(wifes)E92 M3
Join Date: Apr 2007
Location: Toronto

Posts: 6,677
iTrader: (0)

Quote:
Originally Posted by gsrbri View Post
My 2011 E90 ZCP is a daily driver, but sees quite a few track days. Since I purchased the car in July 2011, I've done 8 days (6 at New Hampshire MS and two at Mt. Tremblant). I run stock pads on the street and Pagid RS-19 yellows front and RS-7 black on the rear when on-track. I'm an intermediate-level driver and get into my brakes very hard each lapping session.

After 8 days, my Pagid pads are still good for probably two more track days (wear has been excellent). The rotors, both front/rear, are exhibiting no "lip" after 13,000 miles of spirited driving on the road and track. The Pagid pads, as it turns out, bed very well at the track w/no real need to pre-bed, and I've installed the factory pads directly after being on track, and, as long as you don't hammer the brakes too much, the stock pads remove the bedded material from the Pagids and wipe the rotor clean. No pedal pulsations or anything.

I had a friend that drives an E90 M3 w/PFC-01 pads drive my car at Mt. Tremblant and his impression was that the PFC's offer a little more bite at the limit, but the Pagids are very good. He is seeing much more wear w/the PFC-01s, both on the pads and rotors.

What are your experiences?

-Brian
I ran my 08 car with both Hawk HP+'s & Pagid RS19's for the 3 years that I had my car and my rotors were still in spec after 3 yrs,54000 kms & 40 track days when I sold the car.I use a Stoptech BBK 380/355 on my new car and after about 25 days I changed the front rotor rings due to heat checking not wear.I am using a RS14/29 combination with this setup.
Gearhead999s is offline  
0
Reply With Quote
      08-08-2012, 09:15 AM   #3
TC Kline Racing
BimmerPost Supporting Vendor

 
TC Kline Racing's Avatar
 
Drives: Many BMW's & Porsche's
Join Date: Mar 2012
Location: Columbus, OH & Santa Barbara, CA

Posts: 308
iTrader: (0)

We are a Performance Friction dealer, so we have a little bit of knowledge with them. The 01's are going to be a more aggressive pad and will, in fact, eat rotors a little quicker than some other compounds. Tell your friend that he should look at the PFC 08 compound. It is more of an endurance pad that will last longer, not eat rotors as quickly, and still give good bite and torque.

If the Pagid's are working for you, I would stick with them. It's good to get into different cars, if you can, to see what other brake pads feel like too, so you can compare. Hawk DTC's (60' or 70's) are a good pad for the track as well.
TC Kline Racing is offline   United_States
0
Reply With Quote
      08-08-2012, 09:46 AM   #4
lutfy
Private First Class
 
lutfy's Avatar
 
Drives: 2009 E90 M3 DCT
Join Date: Mar 2012
Location: Washington DC

Posts: 197
iTrader: (1)

Quote:
Originally Posted by gsrbri View Post
I had a friend that drives an E90 M3 w/PFC-01 pads drive my car at Mt. Tremblant and his impression was that the PFC's offer a little more bite at the limit, but the Pagids are very good. He is seeing much more wear w/the PFC-01s, both on the pads and rotors.

What are your experiences?

-Brian
Brian,

I have used PF01s for 3 track events. Each weekend, my pads are almost down to the backing plates (with 1-2mm to spare). Used at Summit Point, Watkins Glen and Summit Point (in that order). Two weeks ago, the pad material literally came off from the backing plate and was dragging on the rotors!!

From my understanding, its the heat which is killing these pads. Long and short, if you go b**s out with 01s in this car, they turn to dust quickly. Not sure if its the heat, drilled rotors, weight or a combination. But this is unacceptable to me (one set of pads each weekend).

I dont have ducting and the car is completely stock just pads and 18*10 wheels with Toyo RA1s (camber pins removed). My fluid holds up fairly well (Motul 600 and I do a quick bleed after each event).

I am going to order the Pagid Yellow next time around. Heard the PF08s are somewhat better?

Lutfy
lutfy is offline  
0
Reply With Quote
      08-08-2012, 10:34 AM   #5
RickyBobby
Lieutenant
 
RickyBobby's Avatar
 
Drives: M3
Join Date: Mar 2008
Location: NorCal

Posts: 452
iTrader: (1)

I had a hard time wearing out my original rotors with various track pads (dtc 70, raybestos st 43, pfc01) and two competitive NASA tt seasons. They were replaced at the 30k service. The moral of the story is that the oem rotors are pretty darn good.
I'm also finding that my 380mm stoptechs are holding up well but will most likely be replaced due to cracking before they wear out. I had some pretty bad luck with the pfc replacement rotors as well.
RickyBobby is offline  
0
Reply With Quote
      08-08-2012, 12:47 PM   #6
lutfy
Private First Class
 
lutfy's Avatar
 
Drives: 2009 E90 M3 DCT
Join Date: Mar 2012
Location: Washington DC

Posts: 197
iTrader: (1)

Quote:
Originally Posted by RickyBobby View Post
I had a hard time wearing out my original rotors with various track pads (dtc 70, raybestos st 43, pfc01) and two competitive NASA tt seasons. They were replaced at the 30k service. The moral of the story is that the oem rotors are pretty darn good.
I'm also finding that my 380mm stoptechs are holding up well but will most likely be replaced due to cracking before they wear out. I had some pretty bad luck with the pfc replacement rotors as well.
RickyBobby, have you heard of Coleman Machines? They make rotors for NASCARS and Prodrive. I have used them in the past (for the 2 piece rotor rings). They can sell you a set heat treated no slotted/cross drilled and are REALLY affordable. Send them your current rotors once (worn out is fine) they can mimic it and will save it in the system for future shipment.

Trey is a great guy there.

There, saved you over 50% in replacement cost

I intend to do the same with my stock rotors once the maint. program runs out. Send them the stock ones, get back 2 piece custom rotors which a) will last much longer b) reduced cost to replace as all I would need would be rings.

Lutfy
lutfy is offline  
0
Reply With Quote
      08-10-2012, 06:27 AM   #7
leo95se
Lieutenant
 
Drives: 09 JB e92, Q5 and passat
Join Date: May 2009
Location: CT

Posts: 488
iTrader: (1)

Hey Lutfy
you know im using the pagids. i like them, but dont/cant drive nearly as hard as you. wore a set down at nj last weekend, but they lasted around 10 track weekends, so not terrible.
i dont think they give the same initial bite as the 01s.

ps - ill be at watkins, i hope in late sept. you in?
leo95se is offline   United_States
0
Reply With Quote
      08-10-2012, 07:15 AM   #8
dawgdog
Colonel
 
dawgdog's Avatar
 
Drives: 2010 Porsche GT3RS
Join Date: Oct 2006
Location: Seattle, Wa.

Posts: 2,114
iTrader: (0)

Warped my stock rotors and replaced with AP BBK. Last season used Mintex F3R pads in front and Mintex Extreme in the rear. I replaced my AP front rotors after two seasons. This year I am using Pagid Yellows front and rear and love them. They are predicable, no fade, and wear evenly.
__________________
AW on Fox Red Extended, Alum trim, ZPP, ZTP, DCT, 19" wheels, Heated front seats, HD radio, Sat radio, I-pod & usb, Premium sound, AP racing BBK, 18 Volk Racing TE 37s, Akrapovic Evolution exhaust, AST suspension
dawgdog is offline  
0
Reply With Quote
      08-10-2012, 08:35 AM   #9
VictorH
Lieutenant
 
Drives: '09 M3
Join Date: Dec 2007
Location: SC

Posts: 594
iTrader: (1)

No one has commented on actual rotor measurements. I have 10,000 street pad miles on my rotors and 6 track days with Pagid RS-19s and my front rotors are at 29.33 mm (wear limit 26 mm something).
VictorH is offline  
0
Reply With Quote
      08-10-2012, 09:42 AM   #10
lutfy
Private First Class
 
lutfy's Avatar
 
Drives: 2009 E90 M3 DCT
Join Date: Mar 2012
Location: Washington DC

Posts: 197
iTrader: (1)

Quote:
Originally Posted by leo95se View Post
Hey Lutfy
you know im using the pagids. i like them, but dont/cant drive nearly as hard as you. wore a set down at nj last weekend, but they lasted around 10 track weekends, so not terrible.
i dont think they give the same initial bite as the 01s.

ps - ill be at watkins, i hope in late sept. you in?
I am going to swap to 08s or even the Pagids and remove the darn backing plate behind the rotor. 10 as in TEN weekends? Brilliant!!!

When pushed, the stock brake system now does (slightly) inspire confidence for me. Going full tilt, the problem is pad turns to dust and at NJ, the pad material came off the backing plate (new set, day 2) and chunks of it disintegrated. Not cool.

I'll be at Glen with GVC

I have a set of 2 PF01 front sets which I may be selling now to replace with something that lasts longer.

Lutfy
lutfy is offline  
0
Reply With Quote
      08-10-2012, 10:19 AM   #11
paradocs98
Major
 
paradocs98's Avatar
 
Drives: 2014 991 Carrera S
Join Date: May 2009
Location: NY

Posts: 1,342
iTrader: (0)

StopTech ST60 380mm front, ST40 355mm rear. After 16,500+ miles of combined street and track driving--12 or so HPDE events which corresponds to 18 or so track days--and two sets of ST Street Perf pads and one set of Pagid RS29s, I'm about to replace my front rotors (actually just the friction rings, since I can keep the rotor hats). I had been measuring my rotor thickness recently, and the original front rotor thickness of 35mm has only gone down about 1mm (2mm wear is the recommended replacement trigger). But I wasn't appreciating the amount of scalloping or lip that was developing on the rotors until my shop pointed it out to me. So I'll be able to get one more event out of this front set of rotors and Pagids, then it's replacement time. Obviously the front pads and rotors are wearing about twice as fast as the rears.

The experience above with the PF 01 pads wearing completely down on stock brakes after one track weekend is interesting. Perhaps the better heat management of a BBK would prevent this? Also, there might be something to be said for Pagid's pad design of having small pegs securing the pad material to the backing plate in addition to adhesive--this is intended to prevent the pad material from delaminating or falling off the backing plate when it wears down.
paradocs98 is offline   United_States
0
Reply With Quote
      08-10-2012, 10:24 AM   #12
VictorH
Lieutenant
 
Drives: '09 M3
Join Date: Dec 2007
Location: SC

Posts: 594
iTrader: (1)

Quote:
Originally Posted by lutfy View Post
RickyBobby, have you heard of Coleman Machines? They make rotors for NASCARS and Prodrive. I have used them in the past (for the 2 piece rotor rings). They can sell you a set heat treated no slotted/cross drilled and are REALLY affordable. Send them your current rotors once (worn out is fine) they can mimic it and will save it in the system for future shipment.

Trey is a great guy there.

There, saved you over 50% in replacement cost

I intend to do the same with my stock rotors once the maint. program runs out. Send them the stock ones, get back 2 piece custom rotors which a) will last much longer b) reduced cost to replace as all I would need would be rings.

Lutfy
Do you have a link? Coleman Machine (at least the first one that comes up) is farm supply and Coleman Racing is out of MI.
VictorH is offline  
0
Reply With Quote
      08-10-2012, 04:05 PM   #13
kartracer12
Private
 
Drives: e90M3 White
Join Date: Mar 2009
Location: VA

Posts: 51
iTrader: (0)

I just installed ST60 and ST40 Stoptech BBK new out of the box and ran one weekend at Summit Point on brand new PF01 pads. I push the car running 1:27-1:30s lap times so pretty hard on the brakes.

Is it normal for the rotors to look like this after one weekend?
Attached Images
 
kartracer12 is offline  
0
Reply With Quote
      08-10-2012, 04:41 PM   #14
arter
collecting toys
 
arter's Avatar
 
Drives: M3 MCB
Join Date: May 2008
Location: rochester, ny

Posts: 745
iTrader: (0)

Have stock rotors and have been using Pagid yellows for 26 track days so far. Just replaced front rotors ( initial 30mm, min 28.4 mm, I was at 28.8 mm) as I saw some cracking around the holes. I was switching to my 3rd set of pagids ( averaging 13 days a set) and decided to switch them with the rotors. Front Rotor cost ~$615 from Turner as DIY.

Love the pagid yellows and happy with stock rotors and brakes so far.
__________________
2011 e92 M3 Monte Carlo Blue ESS 535
2010 Honda FIT
2006 SLK 55 AMG

Last edited by arter; 08-11-2012 at 08:13 PM.
arter is offline  
0
Reply With Quote
      08-11-2012, 03:28 PM   #15
bigjae1976
Takes threads off topic...daily
 
bigjae1976's Avatar
 
Drives: 11 E90 M3 Individual
Join Date: Mar 2006
Location: Milwaukee, WI

Posts: 5,227
iTrader: (11)

Garage List
2004 BMW M3  [4.50]
2011 BMW E90 M3  [5.00]
2013 BMW 328i  [5.00]
The PF01s are not endurance pads. I went through a set on my stock brakes in 5 days at the track.
__________________


Sponsored by Momentum BMW #593...We Bleed BMW BLUE!
bigjae1976 is offline  
0
Reply With Quote
      08-12-2012, 09:27 AM   #16
VP M3
Private First Class
 
VP M3's Avatar
 
Drives: Looking for something new
Join Date: Sep 2008
Location: Toronto

Posts: 106
iTrader: (2)

Pagids & stock rotors

Is anyone running stock rotors with the Pagids on the street / track?

Wondering about noise for daily driving?
VP M3 is offline   Canada
0
Reply With Quote
      08-12-2012, 09:48 AM   #17
HP Man
First Lieutenant
 
Drives: Batmobile
Join Date: Aug 2009
Location: Everywhere

Posts: 306
iTrader: (4)

Pagids work very well but squeal like a pig. Unless you do not mind sounding like a garbage truck, then you will not want to daily drive them.
HP Man is offline  
0
Reply With Quote
      08-13-2012, 07:19 AM   #18
gsrbri
Enlisted Member
 
Drives: E90 M3
Join Date: Jul 2011
Location: Boston, MA

Posts: 46
iTrader: (0)

Rotor photo

I'd check w/the manufacturer, but the pad material that is bedded on the rotor in the photo looks a bit odd, but not all that bad. Maybe a bit intermittent? Which pads are you using? My Pagid RS-19 (front) and RS-7 (rear) pads bed-in w/a good bluish-grey deposit that is very uniform around the rotor (stock M3 rotors).

What did you follow for a bed-in procedure? I'd contact the rotor mfr and send them the photo and get their feedback.

-Brian
gsrbri is offline  
0
Reply With Quote
      08-13-2012, 08:02 AM   #19
kartracer12
Private
 
Drives: e90M3 White
Join Date: Mar 2009
Location: VA

Posts: 51
iTrader: (0)

GSRBRI - Thanks for the feedback. Those were PF01 pads all the way around on my Stoptech rotors. The mechanic at the local shop said he bedded them for me when he installed. Not sure I believe him now.
kartracer12 is offline  
0
Reply With Quote
      08-13-2012, 08:16 AM   #20
Gearhead999s
Major General
 
Gearhead999s's Avatar
 
Drives: E93 335is(wifes)E92 M3
Join Date: Apr 2007
Location: Toronto

Posts: 6,677
iTrader: (0)

Quote:
Originally Posted by VP M3 View Post
Is anyone running stock rotors with the Pagids on the street / track?

Wondering about noise for daily driving?
I did on my other car and they are fairly noisy when cold,but nothing like when I had Hawk HP+'s on.The Pagids are quiet on the street with my ST60/40 setup on my new car.
Gearhead999s is offline  
0
Reply With Quote
      08-13-2012, 09:00 AM   #21
arter
collecting toys
 
arter's Avatar
 
Drives: M3 MCB
Join Date: May 2008
Location: rochester, ny

Posts: 745
iTrader: (0)

My first year I switched between my stock pads and my pagids about 8 times

This year I have just left the pagids on around town. Not that noticeable most of the time, but it will squeak once in a while
__________________
2011 e92 M3 Monte Carlo Blue ESS 535
2010 Honda FIT
2006 SLK 55 AMG
arter is offline  
0
Reply With Quote
      08-13-2012, 09:58 AM   #22
VP M3
Private First Class
 
VP M3's Avatar
 
Drives: Looking for something new
Join Date: Sep 2008
Location: Toronto

Posts: 106
iTrader: (2)

Changing Pads

How difficult and what tools do I need to change by pads myself on stock rotors?
VP M3 is offline   Canada
0
Reply With Quote
Post Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 02:53 PM.




m3post
Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST