BMW M3 Forum (E90 E92)

BMW Garage BMW Meets Register Search Today's Posts Mark Forums Read


Go Back   M3Post - BMW M3 Forum > E90/E92 M3 Technical Topics > DIY Guides/ Discussions
 
Mporium BMW
Post Reply
 
Thread Tools Search this Thread
      06-15-2012, 03:24 PM   #1
mendez
Private
20
Rep
86
Posts

Drives: 2008 e92 M3
Join Date: Jun 2008
Location: Columbus, OH

iTrader: (1)

DIY Radiator Flush

I can't find a DIY for flushing the radiator. Can someone tell me if this is the right procedure?

1. Let the engine cool down.
2. Put the car in ramps/jacks. * Make sure the car height is balanced. The Radiator reservoir has to be the highest.
3. Remove one of the Under body cover
4. Remove the radiator bleeder screw (underneath the car) and let it radiator bleed.
5. Reinstall the bleed screw
6. Fill the radiator with only water. Let the radiator cap off (Pressurized cap) and turn the engine and car heater on. *Keep an eye in the fluid level!!
7. Let the car run for 5-10 min then repeat steps 4-6 like 2 times.
8. After bleeding water, Install a new bleader screw and fill the radiator with 50% Antifreeze-50% water.
9. Turn the engine and car heater on and let the coolant flow with the radiator cap off (to release the air in the system)
10. Turn the engine off, check level and install the radiator cap.

If above steps are ok, I will do it today/tomorrow and post some pictures..

Thanks
Jose
Appreciate 0
      06-15-2012, 03:27 PM   #2
mendez
Private
20
Rep
86
Posts

Drives: 2008 e92 M3
Join Date: Jun 2008
Location: Columbus, OH

iTrader: (1)

I dont know how much is the capacity...Anyone?
Appreciate 0
      06-15-2012, 05:54 PM   #3
VictorH
Major
430
Rep
1,286
Posts

Drives: '09 M3
Join Date: Dec 2007
Location: SC

iTrader: (4)

If you do this, please post plenty of photos. I want to do this too, but haven't seen a DYI yet.

I checked the owner's manual and the only capacities it lists are for the fuel tank and the window washer fluid.
Appreciate 0
      06-15-2012, 06:07 PM   #4
italyix
Captain
italyix's Avatar
United_States
141
Rep
979
Posts

Drives: '08 E90 M3
Join Date: Dec 2011
Location: Bay Area

iTrader: (5)

I found a post for an E46 M3 and the DIY said 2.5 gallons. Ours could be more though...

http://www.m3forum.net/m3forum/showthread.php?t=327613
__________________
Mods: too many the list wont fit in the sig page. PM me
Tesla Referral code: http://ts.la/juliana77782
Appreciate 0
      07-17-2012, 07:59 AM   #5
Sleeper519
Captain
Sleeper519's Avatar
United_States
68
Rep
869
Posts

Drives: 08 E92 M3 DCT
Join Date: Nov 2009
Location: Atlanta, GA

iTrader: (0)

Bump. Any updates? I would like to do this too.
__________________

2008 M3 Coupe / DCT // StopTech BBK 380/355 / Pagid RS29 / Motul / Apex Arc-8 / BFG R1S / Ground Control / MS filter / Performance spoiler / BPM tune // Road Atlanta 1:39.70 / VIR Full 2:10.87 / Barber 1:42.20
Appreciate 0
      07-29-2012, 12:41 PM   #6
pbonsalb
Lieutenant General
5152
Rep
10,532
Posts

Drives: 18 F90 M5, 99 E36 M3 Turbo
Join Date: Feb 2011
Location: New England

iTrader: (4)

I'll be doing it this week. Have not researched it yet. Typically, I find block drain(s) and open those and also the radiator drain. Apparently the system holds 12 quarts so buy 3 gallons if using a pre-mix or 2 gallons if you are mixing with distilled water.
Appreciate 0
      08-14-2012, 06:19 PM   #7
tony093
Captain
tony093's Avatar
111
Rep
746
Posts

Drives: E92 AW M3
Join Date: Jan 2007
Location: Woodbridge, NJ

iTrader: (2)

Quote:
Originally Posted by pbonsalb View Post
I'll be doing it this week. Have not researched it yet. Typically, I find block drain(s) and open those and also the radiator drain. Apparently the system holds 12 quarts so buy 3 gallons if using a pre-mix or 2 gallons if you are mixing with distilled water.
any update?
i'm looking to do this soon.
Appreciate 0
      08-14-2012, 06:32 PM   #8
surlynkid
Major
surlynkid's Avatar
112
Rep
1,470
Posts

Drives: 2013 E92 M3
Join Date: Apr 2012
Location: League City, TX

iTrader: (1)

Garage List
Make sure to use distilled water. It is okay to not know the capacity. Just keep mixing up your own 50/50 blend a little at a time and only add that mix. Keep in mind that there will be residual fluid left in the block after you do these water flushes unless BMW has a plug on the side of the block to remove to get that out. Toyota gives you a block plug to remove. So if you cannot do that, err on the strong side when blend up your coolant and water to end up at 50/50. If you truly knew the capacity, that would help. I would fill and drain 3x with distilled water if I was doing it.
__________________
Stoptech 380mm/355mm | PFC08 / Pagid RS-29 | Akrapovic EVO - CF tips | Benvo Tune | MS UDP | AA air filter | MCS 2-way with 700/1000lb springs | Solid bushings and adjustable links | RD front swaybar | Apex EC-7 18x10 square 275/35-18 NT01 | Turner Race Studs | GT4 Brake Cooling | GT4 Power Steering Cooling | Alekshop Oil Cooler | Performance Steering Wheel | | CF Spoiler | Varis System 1 Full CF Diffuser | Extended Paddle Shifters | Schroth Quick Fit Pro | Turner Steering Rack Stops | Vorshlag Camber Plates
Appreciate 0
      08-15-2012, 09:13 AM   #9
W///
Lieutenant General
W///'s Avatar
7433
Rep
12,291
Posts

Drives: F82GTS, E36/E92M3, Z4M
Join Date: Sep 2011
Location: SC

iTrader: (13)

I've done this job on my other BMW's. Really simple that you probably don't need pictures on this one.

If you were going to flush the radiator, might as well flush what's left in the block too (there's another plug as other members mentioned). Quite a lot of coolant came out of that too.

Be prepared to get soaked though. It's always such a messy job. I recommend wearing safety glasses and have plenty of towels/rags on hand.
__________________
Current:
16 F82 M4 GTS, Black Sapphire/Black, DCT
08 E92 M3, Sparkling Graphite/Bamboo Beige, 6MT
07 E85 Z4M Roadster, Alpine White/Red, 6MT
99 E36 M3, Techno Violet/Dove Grey, 6MT
Appreciate 0
      08-15-2012, 09:33 AM   #10
pbonsalb
Lieutenant General
5152
Rep
10,532
Posts

Drives: 18 F90 M5, 99 E36 M3 Turbo
Join Date: Feb 2011
Location: New England

iTrader: (4)

So where is the block drain on the S65? No one has answered that question yet.

I have flushed coolant on E34, E36, and E39 so I understand the normal process. We are trying to figure out in this thread if there are any E9x M3 specific issues. I still have not gotten to this project so I have nothing to contribute yet.
Appreciate 0
      08-15-2012, 09:52 AM   #11
W///
Lieutenant General
W///'s Avatar
7433
Rep
12,291
Posts

Drives: F82GTS, E36/E92M3, Z4M
Join Date: Sep 2011
Location: SC

iTrader: (13)

Quote:
Originally Posted by pbonsalb View Post
So where is the block drain on the S65? No one has answered that question yet.

I have flushed coolant on E34, E36, and E39 so I understand the normal process. We are trying to figure out in this thread if there are any E9x M3 specific issues. I still have not gotten to this project so I have nothing to contribute yet.
I haven't crawled under there myself yet but if you've done those, then I'm sure you'll be fine. Same goes to anyone that's ever done a full coolant flush on a BMW.

There's nothing else down there. You're either draining oil or coolant from the block
__________________
Current:
16 F82 M4 GTS, Black Sapphire/Black, DCT
08 E92 M3, Sparkling Graphite/Bamboo Beige, 6MT
07 E85 Z4M Roadster, Alpine White/Red, 6MT
99 E36 M3, Techno Violet/Dove Grey, 6MT
Appreciate 0
      08-15-2012, 12:30 PM   #12
pbonsalb
Lieutenant General
5152
Rep
10,532
Posts

Drives: 18 F90 M5, 99 E36 M3 Turbo
Join Date: Feb 2011
Location: New England

iTrader: (4)

One internet report I read stated that there is no block drain. Does anyone know?
Appreciate 0
      10-15-2012, 07:06 PM   #13
meko
First Lieutenant
meko's Avatar
No_Country
177
Rep
387
Posts

Drives: E92 M3 - 535i Sport
Join Date: Oct 2010
Location: New Jersey

iTrader: (3)

Anyone do this yet?
Appreciate 0
      10-15-2012, 07:37 PM   #14
bimdo
Lieutenant
bimdo's Avatar
United_States
42
Rep
486
Posts

Drives: 2008 e90 m3
Join Date: Jan 2012
Location: usa

iTrader: (0)

Quote:
Originally Posted by surlynkid View Post
Make sure to use distilled water. It is okay to not know the capacity. Just keep mixing up your own 50/50 blend a little at a time and only add that mix. Keep in mind that there will be residual fluid left in the block after you do these water flushes unless BMW has a plug on the side of the block to remove to get that out. Toyota gives you a block plug to remove. So if you cannot do that, err on the strong side when blend up your coolant and water to end up at 50/50. If you truly knew the capacity, that would help. I would fill and drain 3x with distilled water if I was doing it.
+1 on the distilled water,it's a cheap way to help prevent corrosion.tap water has a lot of minerals which are bad for radiators.i just had a radiator flush and refill done at the dealer,brought in 2 gallons of distilled water for them to use,1 was still about half full,so about 3 gallons was the total fill.

the manual says the coolant is lifetime fill.i plan to change it every 3-4 years.does anyone who is more mechanically savvy than me think it can really be left unchanged for the life of the car?

Last edited by bimdo; 10-15-2012 at 08:26 PM..
Appreciate 0
      10-18-2012, 10:35 AM   #15
W///
Lieutenant General
W///'s Avatar
7433
Rep
12,291
Posts

Drives: F82GTS, E36/E92M3, Z4M
Join Date: Sep 2011
Location: SC

iTrader: (13)

Quote:
Originally Posted by robbiedawg View Post
+1 on the distilled water,it's a cheap way to help prevent corrosion.tap water has a lot of minerals which are bad for radiators.i just had a radiator flush and refill done at the dealer,brought in 2 gallons of distilled water for them to use,1 was still about half full,so about 3 gallons was the total fill.

the manual says the coolant is lifetime fill.i plan to change it every 3-4 years.does anyone who is more mechanically savvy than me think it can really be left unchanged for the life of the car?
Wow it says it's a lifetime fluid? No way in hell. It starts breaking down after many heat cycles.

I don't track my car, but I still do a full fluid flush every 2 years. Easy job (although messy), but well worth it I think.
__________________
Current:
16 F82 M4 GTS, Black Sapphire/Black, DCT
08 E92 M3, Sparkling Graphite/Bamboo Beige, 6MT
07 E85 Z4M Roadster, Alpine White/Red, 6MT
99 E36 M3, Techno Violet/Dove Grey, 6MT
Appreciate 1
      10-18-2012, 11:56 AM   #16
pbonsalb
Lieutenant General
5152
Rep
10,532
Posts

Drives: 18 F90 M5, 99 E36 M3 Turbo
Join Date: Feb 2011
Location: New England

iTrader: (4)

So how do you do your full coolant fluid flush on your 08 M3? Where is the block drain on this engine?
Appreciate 0
      10-22-2012, 02:52 PM   #17
RBB
First Lieutenant
RBB's Avatar
22
Rep
344
Posts

Drives: E92 M3
Join Date: Mar 2012
Location: NOVA

iTrader: (11)

Has anyone done this yet? I'm due, but can't seem to find the information I need. Some posts say there is no block drain, others say there is. What's the consensus?

I've never done a coolant flush on a BMW and it would be awesome if somebody could post pics of the block drain (if it exists) and radiator bleeder screw.
Appreciate 0
      10-24-2012, 07:13 PM   #18
Richbot
Major General
2735
Rep
5,473
Posts

Drives: Jerez Black E90
Join Date: Sep 2007
Location: STL

iTrader: (5)

When they say "lifetime" they mean "it'll last long enough to make it until something else fails catastrophically to the point of needing a rebuild". For those who want 200k+ out of an engine, I'd change it more frequently than "never", or at least drain the rad and refill to get some of the more corrosive, higher dielectric stuff out and dilute it with fresh
__________________
Appreciate 0
      03-14-2013, 09:00 AM   #19
W///
Lieutenant General
W///'s Avatar
7433
Rep
12,291
Posts

Drives: F82GTS, E36/E92M3, Z4M
Join Date: Sep 2011
Location: SC

iTrader: (13)

Still no updates on potential drain plug in the block? I'm about to do this tonight or tomorrow, guess I might as well check for myself if no one has looked yet.
__________________
Current:
16 F82 M4 GTS, Black Sapphire/Black, DCT
08 E92 M3, Sparkling Graphite/Bamboo Beige, 6MT
07 E85 Z4M Roadster, Alpine White/Red, 6MT
99 E36 M3, Techno Violet/Dove Grey, 6MT
Appreciate 0
      03-14-2013, 10:14 AM   #20
JonM
Lieutenant
140
Rep
409
Posts

Drives: E90 M3 Sedan
Join Date: Sep 2008
Location: Seattle, WA

iTrader: (4)

Quote:
Originally Posted by W/// View Post
Still no updates on potential drain plug in the block? I'm about to do this tonight or tomorrow, guess I might as well check for myself if no one has looked yet.
I was unable to find one. This makes adding a water temp gauge very difficult.

It's a bummer they didn't put one in... on other BMWs it makes it really easy to get ALL the fluid out, albeit messy.
__________________
Jon Maddux
coupenut.blogspot.com
x5nut.blogspot.com
16 X5d | 08 M3 Sedan | 06 M Coupe | 01 M coupe | 99 M coupe
Appreciate 1
Fr0gman19.50
      03-19-2013, 06:18 PM   #21
jjw2331
First Lieutenant
jjw2331's Avatar
52
Rep
381
Posts

Drives: 2011 JtBlk e92 M3
Join Date: Sep 2008
Location: Michigan

iTrader: (6)

So... I gave this coolant flush a try and to my disappointment, I was unsuccessful in accomplishing a full flush.

Two problems:

1. I cannot locate the engine block drain.

2. I do not know the volume of the whole coolant system.

What I bought:

Two gallons of BMW antifreeze/coolant (one shown), 2 gallons of distilled water (one extra), new radiator drain plug - part#17117530902



What I did:

1. Jack up the car and level. Remove the felt panels underneath the bumper (Left, Center and Right). They are mounted with 8mm screws and 3x 10mm screws on the back of the center piece connected to the metal skid plate.

(L piece - part# 51757896419, R piece - part# - 51757896420 )

- Unhooked (twist and slide to bigger hole) the hangers holding the center piece on both sides - part# 51757899820



2. Found the radiator drain plug (left side underneath the radiator).



3. Used a large phillips to unscrew it and drain.



4. Replugged the radiator drain hole with the old plug.

5. Filled the reservoir to about halfway with %50 BMW coolant / %50 distilled H20 (made separately in a container). The ball on the floating stick sat above the fill line.

6. Removed the bleed screw and fill cap. Start the engine and turn heater on highest temp without putting the fan on high.

7. I let the engine get to about 140 degrees F (took about 7-8 mins and heat starts coming out of cabin vents) and then shut down. Repeated steps 3.-6. three times using a new drain plug when done.

8. On the final fill, I filled to full and closed the bleed screw, opening and closing to let the air bubbles out while the engine is on. When there are no more bubbles, I used a turkey baster to remove some coolant from the reservoir.



The issues:

Since I did not know the volume of the coolant system, I did not try to flush the entire system using pure distilled water. The ratio of coolant to water would've been unknown when it came time to fill. I made a premix of 50/50 coolant/H20 and filled with that after each drain. Each drain yielded about 1 gallon of coolant.

What my method hopes to accomplish is to dilute old coolant with new coolant. This is why I mentioned this is NOT a flush but a way to get keep the coolant somewhat fresh. My car is just under 2 years old and I have about 28,000 miles.

If anyone knows a full flush method please let us know. For the time being, if anyone sees other problems with my method in addition to what I mentioned or has a better method than mine please let me and the rest of us know.

Last edited by jjw2331; 03-20-2013 at 01:04 PM..
Appreciate 0
      03-19-2013, 06:41 PM   #22
bimdo
Lieutenant
bimdo's Avatar
United_States
42
Rep
486
Posts

Drives: 2008 e90 m3
Join Date: Jan 2012
Location: usa

iTrader: (0)

in some correspondence about radiator flushes with mike miller of roundel,he said that bmw had made it hard to do a full coolant flush on bmw's built after 2006 without extensive,and therefore expensive,disassembly,and that because of that the best you can do is drain and fill the radiator,which it looks like you have done.

hth
Appreciate 0
Post Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 02:27 AM.




m3post
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST