BMW M3 Forum (E90 E92)

BMW Garage BMW Meets Register Search Today's Posts Mark Forums Read


Go Back   M3Post - BMW M3 Forum > E90/E92 M3 Technical Topics > Suspension | Brakes | Chassis
 
European Auto Source
Post Reply
 
Thread Tools Search this Thread
      03-05-2012, 07:38 AM   #1
Bubbles
Green Bastard
 
Bubbles's Avatar
 
Drives: ZCP-Powered
Join Date: Jun 2007
Location: Bishop Bend

Posts: 3,545
iTrader: (3)

Replaced Brake Lines

I followed Mr.5's DIY to replace the mid brake lines (here:http://www.e90post.com/forums/showpo...1&postcount=17).
One of the more challenging mods I've worked on to date. My hands paid the price because there isn't much room to work with.

I went with Stoptech Stainless lines. Great quality but I wish the lines had the "star design" at the hose connects that the OEM lines have to prevent rotation as you tighten down the lines. ECS lines have this with their "exact fit" lines. It wasn't a huge issue, but given the challenge in swapping the mid lines, every bit helps. The install for the lines to the calipers are a breeze.

Tip #1: depress the brake pedal about 2 inches using something to wedge between the seat and the pedal to prevent significant fluid loss while you are wrenching away. The fluid loss was minimal during the nearly three hour install (second time around will go quicker).

Tip #2: You need a quality Flare Nut Wrench 11m to loosen and tighten the hard lines. The metal is soft and will round off very easily. I bought 6 identical wrenches from pep boys, out of the six only one had the tolerance I was comfortable with. Also, I hit the bolts with Liquid Wrench (any penetrating oil should work) the day before to ease breaking the nut free. I loosened it to the point I could use my fingers to remove the line.

Did a full flush with Castrol SRF brake fluid using a Motive pressure bleeder. I always pull the old fluid from the reservoir with a measuring syringe as there is no reason to push old fluid through the system (don't pull too much and add air). I then top off the fluid reservoir with fresh fluid and attach the pressure bleeder (I don't add fluid to the pressure bleeder). Start with RR, RL, FR, FL (Facing the rear of the car).

I bled the rear lines first. Starting with the RR line until nearly half the reservoir was depleted, released the pressure AT THE BLEEDER TOP, then refilled the reservoir and bled the RL line. Refilled the reservoir again and bled the FR and FL (Refill was necessary due to the length of the lines).

The Feel: I was skeptical at first, but the feel is great, tremendous actually. Much more brake-by-wire feel. The OEM lines are very good, but the difference in pedal feel is significant. The true test will be at the track, I expect consistent firm pedal feel for longer than can be achieved with stock lines.

Running Stoptech ST-60s with Pagids RS29s on the front and Stock Calipers and RS-7 Pagids on the rears.
Attached Images
     
__________________

Last edited by Bubbles; 03-05-2012 at 09:19 AM.
Bubbles is offline   Cayman Islands
0
Reply With Quote
      03-05-2012, 09:20 AM   #2
Wendall
***Major MammelToe
 
Wendall's Avatar
 
Drives: E92 M3 SG coupe
Join Date: Feb 2012
Location: Orange County, CA

Posts: 1,146
iTrader: (3)

Feel any difference?
__________________
E92 M3 SG DCT - AA Filter, Verstraβe Paddles, ECS SS, MH race stud, Stoptech BBK, MR Exhaust,RE Pulley, BPM Tune,Euro bumper and GTS lip, Euro MDM & DCT, KW CS, Recaro PP, TMS Soild Diff Mounts, MRF solid subframe mounts, GTS aero, RPM track built motor.

Wendall is offline   United_States
0
Reply With Quote
      03-05-2012, 10:51 AM   #3
mkPOTO
Mr. Nice Says Hello
 
mkPOTO's Avatar
 
Drives: 1999 528I
Join Date: Dec 2008
Location: USA

Posts: 15,297
iTrader: (23)

Garage List
i did when i ran the same lines, pedal feels stiffer and when you stomp on them there isnt much delay like stock (it might be all in my head lol)
__________________
EVOLVE BMW E92 M3
mkPOTO is offline  
0
Reply With Quote
      03-05-2012, 11:07 AM   #4
Bubbles
Green Bastard
 
Bubbles's Avatar
 
Drives: ZCP-Powered
Join Date: Jun 2007
Location: Bishop Bend

Posts: 3,545
iTrader: (3)

Quote:
Originally Posted by biggynuts01 View Post
Feel any difference?
Quote:
Originally Posted by mkPOTO View Post
i did when i ran the same lines, pedal feels stiffer and when you stomp on them there isnt much delay like stock (it might be all in my head lol)

Well put mkPOTO, the seems to be a reduction in the delay, a much more brake-by-wire feeling.

The pedal feels great.
__________________
Bubbles is offline   Cayman Islands
0
Reply With Quote
      03-05-2012, 02:21 PM   #5
e92zero
Lieutenant
 
Drives: 2011 E92 BW
Join Date: May 2010
Location: somewhere in US

Posts: 520
iTrader: (0)

^^^mkPOTO/Bubbles, how much of the pedal feel difference do you think is because of the fresh/new/different brake fluid vs the ss brake lines?
e92zero is offline  
0
Reply With Quote
      03-05-2012, 02:51 PM   #6
mkPOTO
Mr. Nice Says Hello
 
mkPOTO's Avatar
 
Drives: 1999 528I
Join Date: Dec 2008
Location: USA

Posts: 15,297
iTrader: (23)

Garage List
Quote:
Originally Posted by e92zero View Post
^^^mkPOTO/Bubbles, how much of the pedal feel difference do you think is because of the fresh/new/different brake fluid vs the ss brake lines?
less travel for sure, i dont have to stomp on them to stop, now all i have to do is push it lightly. Huge difference from when I went to the track with stock lines, I had to brake early sometimes and now I just push it alittle more brake better on the aftermarket lines
__________________
EVOLVE BMW E92 M3
mkPOTO is offline  
0
Reply With Quote
      03-05-2012, 07:27 PM   #7
Bubbles
Green Bastard
 
Bubbles's Avatar
 
Drives: ZCP-Powered
Join Date: Jun 2007
Location: Bishop Bend

Posts: 3,545
iTrader: (3)

Quote:
Originally Posted by e92zero View Post
^^^mkPOTO/Bubbles, how much of the pedal feel difference do you think is because of the fresh/new/different brake fluid vs the ss brake lines?

When I swapped on the BBK a few weeks ago, the pedal did not feel this linear. Even cold, the feel is different.

I've flushed my brake system before with fresh SRF fluid and this feel is not from new fluid.
__________________
Bubbles is offline   Cayman Islands
0
Reply With Quote
      03-05-2012, 07:34 PM   #8
e92zero
Lieutenant
 
Drives: 2011 E92 BW
Join Date: May 2010
Location: somewhere in US

Posts: 520
iTrader: (0)

^^^Thanks for the info, mkPOTO/Bubbles.
e92zero is offline  
0
Reply With Quote
      03-07-2012, 07:51 AM   #9
Bubbles
Green Bastard
 
Bubbles's Avatar
 
Drives: ZCP-Powered
Join Date: Jun 2007
Location: Bishop Bend

Posts: 3,545
iTrader: (3)

My hands are healing and I must say the upgrade is worth it.
__________________
Bubbles is offline   Cayman Islands
0
Reply With Quote
      03-07-2012, 08:54 AM   #10
Sleeper519
Captain
 
Sleeper519's Avatar
 
Drives: 08 E92 M3 DCT
Join Date: Nov 2009
Location: Atlanta, GA

Posts: 721
iTrader: (0)

Nice job. Didn't the BBK kit come with SS lines?

I thought it was interesting that you don't fill the pressure bleeder with fluid, just refill the reservoir periodically. Any advantages? I may try this just to keep the bleeder hoses from getting all gooey.
__________________

2008 M3 Coupe / DCT // StopTech BBK 380/355 / Pagid RS29 / Motul / Apex Arc-8 / BFG R1S / Ground Control / MS filter / Performance spoiler / BPM tune // Road Atlanta 1:39.80 / VIR Full 2:10.87 / Barber 1:42.20
Sleeper519 is offline   United_States
0
Reply With Quote
      03-07-2012, 09:04 AM   #11
LiM3y
Major
 
LiM3y's Avatar
 
Drives: 2008 E90 M3
Join Date: Jun 2009
Location: CT

Posts: 1,196
iTrader: (2)

Quote:
Originally Posted by Sleeper519 View Post
Nice job. Didn't the BBK kit come with SS lines?

I thought it was interesting that you don't fill the pressure bleeder with fluid, just refill the reservoir periodically. Any advantages? I may try this just to keep the bleeder hoses from getting all gooey.
I have tried both methods and now just refill the reservoir and use the power bleeder to provide pressure. If you use hose clamps (I put a ball valve in the bleeder hose), you can keep the pressure in the bottle while you top off the reservoir in between bleeds.
__________________
LiM3y is offline   United Kingdom
0
Reply With Quote
      03-07-2012, 09:04 AM   #12
THE TECH
BimmerPost Supporting Vendor

 
THE TECH's Avatar
 
Drives: BPMsport 2012 E92 M3
Join Date: Jun 2011
Location: Kansas

Posts: 13,001
iTrader: (42)

Garage List
Send a message via AIM to THE TECH Send a message via Skype™ to THE TECH
Quote:
Originally Posted by Sleeper519 View Post
Nice job. Didn't the BBK kit come with SS lines?

I thought it was interesting that you don't fill the pressure bleeder with fluid, just refill the reservoir periodically. Any advantages? I may try this just to keep the bleeder hoses from getting all gooey.
+1
__________________
THE TECH is offline   United_States
0
Reply With Quote
      03-07-2012, 09:29 AM   #13
THE TECH
BimmerPost Supporting Vendor

 
THE TECH's Avatar
 
Drives: BPMsport 2012 E92 M3
Join Date: Jun 2011
Location: Kansas

Posts: 13,001
iTrader: (42)

Garage List
Send a message via AIM to THE TECH Send a message via Skype™ to THE TECH
Also, which Motive bleeder cap are you using? I need to buy the Euro one for mine and they make two different ones.
__________________
THE TECH is offline   United_States
0
Reply With Quote
      03-07-2012, 11:11 AM   #14
Bubbles
Green Bastard
 
Bubbles's Avatar
 
Drives: ZCP-Powered
Join Date: Jun 2007
Location: Bishop Bend

Posts: 3,545
iTrader: (3)

Quote:
Originally Posted by Sleeper519 View Post
Nice job. Didn't the BBK kit come with SS lines?

I thought it was interesting that you don't fill the pressure bleeder with fluid, just refill the reservoir periodically. Any advantages? I may try this just to keep the bleeder hoses from getting all gooey.
I bought my BBK used (front only), so I don't blame the seller for not wanting to deal with the mid-lines. I did swap all brakes to SS lines (including the stock rear calipers) I don't fill the pressure bleeder because I believe if you factor in clean up time, not filling the pressure bleeder saves you time. Plus, I like to keep my risk of brake fluid spillage to a single location and I think it adds to the longevity of the bleeder's hoses.

Quote:
Originally Posted by LiM3y View Post
I have tried both methods and now just refill the reservoir and use the power bleeder to provide pressure. If you use hose clamps (I put a ball valve in the bleeder hose), you can keep the pressure in the bottle while you top off the reservoir in between bleeds.
Interesting, but I'm conservative and release the pressure completely between fills, again just a cost benefit to me.

Quote:
Originally Posted by THE TECH View Post
Also, which Motive bleeder cap are you using? I need to buy the Euro one for mine and they make two different ones.
I believe it's the Motive European "Black Label", it's not the one that comes with the bleeder.
__________________
Bubbles is offline   Cayman Islands
0
Reply With Quote
      03-07-2012, 11:17 AM   #15
THE TECH
BimmerPost Supporting Vendor

 
THE TECH's Avatar
 
Drives: BPMsport 2012 E92 M3
Join Date: Jun 2011
Location: Kansas

Posts: 13,001
iTrader: (42)

Garage List
Send a message via AIM to THE TECH Send a message via Skype™ to THE TECH
Quote:
Originally Posted by Bubbles View Post
I believe it's the Motive European "Black Label", it's not the one that comes with the bleeder.
Thanks.
__________________
THE TECH is offline   United_States
0
Reply With Quote
      03-08-2012, 04:06 PM   #16
adc
Brigadier General
 
Drives: 2009 E90 M3 ED
Join Date: Sep 2006
Location: MD/DC

Posts: 4,073
iTrader: (6)

I just replaced my clutch slave cylinder in my Miata, for which I had to buy a set of flare wrenches. I can feel the success of that operation coupled with the new tools pushing me towards doing this mod on the M3. lol.

Thanks Bubbles!
__________________

2009 E90 M3 ED
2014 X1 28i
2000 Boxster
adc is offline  
0
Reply With Quote
      03-09-2012, 07:15 AM   #17
1SICKM
Captain
 
1SICKM's Avatar
 
Drives: 2009 M3 E92
Join Date: Oct 2010
Location: Mansfield, NJ

Posts: 946
iTrader: (5)

How does depressing the brake pedal prevent fluid loss? I would think it creates more because your pressurizing the system
__________________
E92 M3 DCT...Powered by ESS VT2 650/DCT GTS Software/Aquamist HFS-3 50/50/Morr /Toyo R888's

CURRENT WORLD RECORD HOLDER 1/4 MILE - 12/7/12 (ESS VT2 625, Meth Off)
ATCO RACEWAY: 10.65 @ 131.79MPH 1.725 60FT
1SICKM is offline  
0
Reply With Quote
      03-09-2012, 08:15 AM   #18
Bubbles
Green Bastard
 
Bubbles's Avatar
 
Drives: ZCP-Powered
Join Date: Jun 2007
Location: Bishop Bend

Posts: 3,545
iTrader: (3)

Quote:
Originally Posted by adc View Post
I just replaced my clutch slave cylinder in my Miata, for which I had to buy a set of flare wrenches. I can feel the success of that operation coupled with the new tools pushing me towards doing this mod on the M3. lol.

Thanks Bubbles!
Do it man, you won't regret it!

Quote:
Originally Posted by 1SICKM View Post
How does depressing the brake pedal prevent fluid loss? I would think it creates more because your pressurizing the system
You'd think but it actually slows the fluid loss, think of it creating a pseudo closed system.
__________________
Bubbles is offline   Cayman Islands
0
Reply With Quote
      03-09-2012, 09:29 AM   #19
schnell325
Bored at work....
 
schnell325's Avatar
 
Drives: '08 M3,'11 335xi
Join Date: Aug 2007
Location: BC

Posts: 3,818
iTrader: (5)

Good to see a review of the Stoptech SS lines.
schnell325 is offline   Canada
0
Reply With Quote
      03-09-2012, 11:54 AM   #20
JAJ
Captain
 
Drives: 2014 Shelby GT500
Join Date: Apr 2008
Location: Vancouver, BC

Posts: 923
iTrader: (4)

Quote:
Originally Posted by 1SICKM View Post
How does depressing the brake pedal prevent fluid loss? I would think it creates more because your pressurizing the system
When the brake pedal is fully released, there's a duct that opens between the reservoir and the master cylinder. As the pads wear, fluid flows from the reservoir into the master cyliner to keep the system full.

When the pedal moves forward, the first few millimeters of movement close this duct off. If you close the duct before you open up the brake lines, no fluid can flow into, through and out of the master cylinder. Surface tension combined with the slight vacuum that forms keeps the system from draining while you work on it.
JAJ is offline  
0
Reply With Quote
      03-12-2012, 06:16 AM   #21
Bubbles
Green Bastard
 
Bubbles's Avatar
 
Drives: ZCP-Powered
Join Date: Jun 2007
Location: Bishop Bend

Posts: 3,545
iTrader: (3)

Quote:
Originally Posted by JAJ View Post
When the brake pedal is fully released, there's a duct that opens between the reservoir and the master cylinder. As the pads wear, fluid flows from the reservoir into the master cyliner to keep the system full.

When the pedal moves forward, the first few millimeters of movement close this duct off. If you close the duct before you open up the brake lines, no fluid can flow into, through and out of the master cylinder. Surface tension combined with the slight vacuum that forms keeps the system from draining while you work on it.

Good explanation, thanks.
__________________
Bubbles is offline   Cayman Islands
0
Reply With Quote
      03-12-2012, 11:24 AM   #22
THE TECH
BimmerPost Supporting Vendor

 
THE TECH's Avatar
 
Drives: BPMsport 2012 E92 M3
Join Date: Jun 2011
Location: Kansas

Posts: 13,001
iTrader: (42)

Garage List
Send a message via AIM to THE TECH Send a message via Skype™ to THE TECH
Where's everyone getting their Castrol SRF from? And, are you buying more than one liter for the flush?
__________________

Last edited by THE TECH; 03-12-2012 at 01:47 PM.
THE TECH is offline   United_States
0
Reply With Quote
Post Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 05:18 AM.




m3post
Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST