BMW M3 Forum (E90 E92)

BMW Garage BMW Meets Register Search Today's Posts Mark Forums Read


Go Back   M3Post - BMW M3 Forum > E90/E92 M3 Technical Topics > DIY Guides/ Discussions
 
GT Haus
Post Reply
 
Thread Tools Search this Thread
      05-15-2011, 07:57 PM   #1
BimmerM
Lieutenant
 
BimmerM's Avatar
 
Drives: '11.5 E92 M3, '05 X5 4.8is
Join Date: Mar 2008
Location: NYC

Posts: 528
iTrader: (0)

Garage List
2005 BMW X5 4.8is  [0.00]
2011 BMW M3  [0.00]
DIY: Replace Side Gills (easy method) on E92 M3

I took over 2 months before I finally installed my gills (back in January) as I wanted to figure out an easier method to install them. Here's how I installed mine. Hopefully it'll help you guys. Once you get the hang of doing one side your see it'll take you less than a minute to pop them out. Hopefully this will help you guys.

Tools Required
  • Scotch Packing Tape (or any super strength tape that doesn't leave adhesive behind when you peel it off)
  • Blue Painters Tape

Before you begin:
If you are afraid of scratching your car, tape the painted surface around the gills with painters tape

Installation

Step 1. Remove OEM chrome side gill

Apply packing tape to the end closest to the door (ie. the part pointing toward the rear of the car). To apply the tape, pull a long strip of tape and tape the ends to the top and bottom of the gill then press the tape together.

Assuming you are working on the driver's side (left) gill (you will do the opposite for the other side):
  • Use your right hand and grasp the long piece of the tape with your right palm and your last three fingers (your middle finger, ring finger, and pinky finger).
  • Now using your right thumb and pointer finger, grab the top and bottom of the gill pressing down on the tape.
  • So that your left hand don't feel lonely, grab the middle of the gill with the fingers from your left hand.
  • Wiggle up and down while you pull on the tape.
  • The gill should pop right out easily.



Step 2. Do not drop the wire behind the fender

Tilt the gill out of the fender to expose and pull it out.

Before you disconnect the wiring, use some painters tape to tape down the wiring so that it doesn't fall behind the fender. If it fall behind the fender you will extend your install time MUCH MUCH longer trying to fish it out.

Once the wire is secure and you know it won't fall behind the fender, unlatch the wiring harness plug from the gill.



Step 3. Install new gill

Finally, the easy part!

Plug the wiring harness into the new side gill then insert the larger end of the gill into the fender and line up the mounting points.

Simply press the gill into the mounting points till it's flush. You are done!



Below is a comparison of the OEM chrome gill vs the new OEM M3 Edition black chrome gill



Disclaimer: Use this DIY at your own risk, I'm not responsible for any damage to your car.
__________________

Drives: '11.5 Interlagos Blue E92 M3, '05 LeMans Blue X5 4.8is
Sold: '03.5 Mystic Blue E46 M3
DIYs: Enable Rear Fog | Easy Side Gill Replacement | Front Grill Replacement
BimmerM is offline   United_States
0
Reply With Quote
      05-15-2011, 11:37 PM   #2
Bimmerboy888
Lieutenant
 
Bimmerboy888's Avatar
 
Drives: E92 M3 DCT
Join Date: Nov 2009
Location: OC

Posts: 462
iTrader: (0)

Great way to do it!
__________________
BAVARIANBEAST
Bimmerboy888 is offline   United_States
0
Reply With Quote
      05-16-2011, 11:38 PM   #3
stealthM3
Private First Class
 
stealthM3's Avatar
 
Drives: 08 e90 M3
Join Date: May 2010
Location: OC

Posts: 121
iTrader: (0)

Nice man and thanks for the DIY! Im assuming it'll be the same for the e90 though? Heard alot about it being harder on the e90 for some reason...any more pics of the black chrome installed? BTW where did you get them from? Thanks!
stealthM3 is offline  
0
Reply With Quote
      05-17-2011, 12:17 PM   #4
BimmerM
Lieutenant
 
BimmerM's Avatar
 
Drives: '11.5 E92 M3, '05 X5 4.8is
Join Date: Mar 2008
Location: NYC

Posts: 528
iTrader: (0)

Garage List
2005 BMW X5 4.8is  [0.00]
2011 BMW M3  [0.00]
Quote:
Originally Posted by stealthM3 View Post
Nice man and thanks for the DIY! Im assuming it'll be the same for the e90 though? Heard alot about it being harder on the e90 for some reason...any more pics of the black chrome installed? BTW where did you get them from? Thanks!
I'm not too certain on the E90 as I have not done it on the E90. However, I would assume it would come out similiar.

I bought my M3 "Edition" gills from getBMWParts.com.

Unfortunately I haven't really taken too many closeup shots of them installed. If you search on the forum there's many that have posted pics of them installed.
__________________

Drives: '11.5 Interlagos Blue E92 M3, '05 LeMans Blue X5 4.8is
Sold: '03.5 Mystic Blue E46 M3
DIYs: Enable Rear Fog | Easy Side Gill Replacement | Front Grill Replacement
BimmerM is offline   United_States
0
Reply With Quote
      06-10-2011, 05:57 PM   #5
phildeez010
Private First Class
 
Drives: 2011 E92 M3
Join Date: Feb 2011
Location: Los Angeles

Posts: 171
iTrader: (6)

This DIY worked out great, just make sure to put a thick layer of blue tape to avoid scratches. Also let the car sit in the some for a bit he helps out
phildeez010 is offline  
0
Reply With Quote
      06-22-2011, 09:41 PM   #6
艾利克斯
Private First Class
 
Drives: SG E92 M3
Join Date: Mar 2011
Location: Vancouver, B.C

Posts: 114
iTrader: (1)

Great method!
Actually I found it's easier to do with two people.
I have my girlfriend pulling the tape while I pull the gill upwards, and it pop off easily.
艾利克斯 is offline   Canada
0
Reply With Quote
      06-26-2011, 05:24 AM   #7
bobs619
First Lieutenant
 
bobs619's Avatar
 
Drives: 2014 Saphire Black F10 M5
Join Date: Mar 2011
Location: San Diego

Posts: 366
iTrader: (0)

+1 worked for me!
bobs619 is offline   United_States
0
Reply With Quote
      07-07-2011, 06:45 PM   #8
Brucewonder
Lieutenant Colonel
 
Brucewonder's Avatar
 
Drives: 2011 E92 M3 yea boi
Join Date: Nov 2007
Location: Socal

Posts: 1,543
iTrader: (4)

worked like a charm to get off the car. 30 sec for each side. Now, the only trouble im having is removing the chrome body from the black end thingy. Cant seem to get the 2 clips loose
Brucewonder is offline  
0
Reply With Quote
      07-18-2011, 07:32 PM   #9
rye m3
Lieutenant
 
rye m3's Avatar
 
Drives: 2011.75 E92 M3
Join Date: Apr 2011
Location: New York

Posts: 489
iTrader: (2)

OMG! You are a genius man! Simply wrap the tape around it, hold the gill with a micro fiber towel, wriggle the gill in the towel and pull hard on the tape. I changed both sides in 10 minutes! Holy crap, to think of people ripping out their fender liners and prying these things off with a screwdriver... This method there was no way you damage anything. They pop out, but not violently, very easy to control and no chance of damaging the paint or the gill.

This board should have reputation points like 6 speed. You certainly earn some with this.
__________________
E92 M3 MR on Red/Black ZCP Sound
Carbon

2007 997S - sold
2003 E46 M3 Steel Grey on Red- sold
1997 E36 M3 Arctic Silver on Black- sold
rye m3 is offline   Switzerland
0
Reply With Quote
      07-18-2011, 07:43 PM   #10
BimmerM
Lieutenant
 
BimmerM's Avatar
 
Drives: '11.5 E92 M3, '05 X5 4.8is
Join Date: Mar 2008
Location: NYC

Posts: 528
iTrader: (0)

Garage List
2005 BMW X5 4.8is  [0.00]
2011 BMW M3  [0.00]
Quote:
Originally Posted by rye m3 View Post
OMG! You are a genius man! Simply wrap the tape around it, hold the gill with a micro fiber towel, wriggle the gill in the towel and pull hard on the tape. I changed both sides in 10 minutes! Holy crap, to think of people ripping out their fender liners and prying these things off with a screwdriver... This method there was no way you damage anything. They pop out, but not violently, very easy to control and no chance of damaging the paint or the gill.

This board should have reputation points like 6 speed. You certainly earn some with this.
Glad you found it useful.
__________________

Drives: '11.5 Interlagos Blue E92 M3, '05 LeMans Blue X5 4.8is
Sold: '03.5 Mystic Blue E46 M3
DIYs: Enable Rear Fog | Easy Side Gill Replacement | Front Grill Replacement
BimmerM is offline   United_States
0
Reply With Quote
      07-29-2011, 07:52 AM   #11
mmaroto
New Member
 
Drives: 2011 M3 e90
Join Date: Jul 2011
Location: Dallas, TX

Posts: 9
iTrader: (0)

Please clarify...

Can this method also be used to replace gills on a 2011 e90? I ask bc of the "grille" on the gills unlike the vert or coupe.

thanks
mmaroto is offline  
0
Reply With Quote
      07-30-2011, 01:55 AM   #12
OC3
Havin' a blast!
 
OC3's Avatar
 
Drives: 2013 M3 E92 Jerez Blk DCT ZCP
Join Date: Nov 2010
Location: SoCal

Posts: 4,716
iTrader: (1)

Quote:
Originally Posted by mmaroto View Post
Please clarify...

Can this method also be used to replace gills on a 2011 e90? I ask bc of the "grille" on the gills unlike the vert or coupe.

thanks
Not so simple on E90, lulz

http://www.m3post.com/forums/showthread.php?t=497779
__________________

BRP CW13 1:58 | CVR CW 2:01 | CVR CCW 2:02 | ACS 1:53 | WSIR 1:34
2013 E92 M3 Jerez Black DCT ZCP | JRZ RS Pro | Brembo BBK | Endless ME20 | Volk TE37 18x10.5 squared | NT01/TD
OC3 is offline   United_States
0
Reply With Quote
      09-28-2011, 09:32 PM   #13
mazing
Private First Class
 
mazing's Avatar
 
Drives: 2011.5 Jet Black M3
Join Date: Jun 2011
Location: Virginia

Posts: 192
iTrader: (1)

Brilliant worked just as indicated. Just completed install on E93 took about 20 mins. Thanks for this method.
__________________
2011 Jet Black Bamboo Novillo/DCT/Gloss Black Grills/Gloss Black Reflectors/Gloss Black Side Gills w/Light Tinted Lenses/Black Vinyl Window Trim
mazing is offline  
0
Reply With Quote
      10-08-2011, 06:20 PM   #14
llis
octane chick
 
llis's Avatar
 
Drives: Ms
Join Date: Oct 2010
Location: Colorado

Posts: 1,131
iTrader: (1)

Garage List
2003 BMW M5  [0.00]
2002 BMW 530i (fs)  [0.00]
2013 BMW M3  [5.00]
Sticky this thread, please!

I am shaking my head, seeing how obvious this approach is, because the hardest thing about swapping gills was getting a firm grip on it to get it out. It takes gorilla grip to do it! But the tape technique could really help.

Now did I read you right: OEM black chrome gills? I got black chrome, but they were not OEM afaik.

Edit: Moderators, please sticky this thread. This is very useful!
__________________

2013 E92 ///M3 ZCP 6MT Speed Yellow 2003 E39 ///M5

Last edited by llis; 10-08-2011 at 06:25 PM. Reason: recommend for sticky
llis is offline   United_States
0
Reply With Quote
      10-08-2011, 10:13 PM   #15
BimmerM
Lieutenant
 
BimmerM's Avatar
 
Drives: '11.5 E92 M3, '05 X5 4.8is
Join Date: Mar 2008
Location: NYC

Posts: 528
iTrader: (0)

Garage List
2005 BMW X5 4.8is  [0.00]
2011 BMW M3  [0.00]
Quote:
Originally Posted by llis View Post
I am shaking my head, seeing how obvious this approach is, because the hardest thing about swapping gills was getting a firm grip on it to get it out. It takes gorilla grip to do it! But the tape technique could really help.

Now did I read you right: OEM black chrome gills? I got black chrome, but they were not OEM afaik.

Edit: Moderators, please sticky this thread. This is very useful!
Yes, it was part of the M3 "Edition" car that was released overseas. The OEM Satin/Black Chrome parts can be ordered from here: http://www.trademotion.com/partlocat...catalogid=4462

__________________

Drives: '11.5 Interlagos Blue E92 M3, '05 LeMans Blue X5 4.8is
Sold: '03.5 Mystic Blue E46 M3
DIYs: Enable Rear Fog | Easy Side Gill Replacement | Front Grill Replacement
BimmerM is offline   United_States
0
Reply With Quote
      11-21-2011, 09:42 AM   #16
JRV
Lieutenant
 
Drives: 2011.75 AWE90M3
Join Date: Aug 2008
Location: Bedford, NY

Posts: 483
iTrader: (1)

To the OP - I love you! LOL This worked like a charm. It was much better than the screw driver trick. The only thing i added was 2 more strips of packing tape from the little end towards the middle for more leverage...you rock!
__________________
'08 Silver/Black C300 (Wife)
'04 Jeep Grand Cherokee Limited V8 (My beater)
Loaded AW Fox Red/Black/Black Carbon Leather ZCP E90 M3 (Halloween Delivery)
JRV is offline   United_States
0
Reply With Quote
      12-14-2011, 05:00 PM   #17
jwarner
Private
 
Drives: 2011 E92 Alpine White ZCP
Join Date: May 2011
Location: Sammamish, WA

Posts: 82
iTrader: (2)

Video instructions

I followed this advice, and it worked extremely well. The packing tape is the key method for getting the gill off with no fuss, all other methods risk scratching the paint or using too much force, in my opinion.

I did the first gill replacement, and then took videos of the second.

Before you start, it's worth watching all 4 videos (sorry, I don't have time to splice them together) so you know all the steps.

Overall, this is a very simple procedure that even non-mechanically inclined people can do.

Now that I've done one set, I could do 1 gill replace and removal in probably 7-8 minutes, so 15 minutes for both sides.

I hope this is useful.

Part 1 is here:

Part 2 is here

Part 3 is here

Part 4 is here
jwarner is offline  
0
Reply With Quote
      12-14-2011, 05:07 PM   #18
jwarner
Private
 
Drives: 2011 E92 Alpine White ZCP
Join Date: May 2011
Location: Sammamish, WA

Posts: 82
iTrader: (2)

By the way, this should probably be a sticky thread.

Jason
jwarner is offline  
0
Reply With Quote
      12-14-2011, 07:56 PM   #19
ss134
Brigadier General
 
ss134's Avatar
 
Drives: ...a hard bargain...
Join Date: Feb 2009
Location: Germany/UK

Posts: 3,649
iTrader: (1)

Quote:
Originally Posted by mmaroto View Post
Please clarify...

Can this method also be used to replace gills on a 2011 e90? I ask bc of the "grille" on the gills unlike the vert or coupe.

thanks
Even my dealer managed to break the plastic vents when they changed the side grilles for me on my old car - for the E90 the safest way is to remove the wheels and go in from the wheel well - it can be done without doing this but youre taking a risk of something breaking.
__________________
2014 AW F80 M3 DCT
2011 AW E90 M3 DCT - Sold
2010 JZB E90 M3 DCT - Sold
2009 6MT E90 LCI 335i M -Sport - Sold
ss134 is offline   United Kingdom
0
Reply With Quote
      12-30-2011, 08:07 PM   #20
0311_grunt
Second Lieutenant
 
Drives: 2008 M3
Join Date: Apr 2009
Location: Superior, CO

Posts: 260
iTrader: (0)

Took 20 min total with replacing all the parts and whatnot. I'm glad I stumbled upon this...all the other DIY's were way too difficult..
0311_grunt is offline  
0
Reply With Quote
      01-02-2012, 12:26 AM   #21
skins333
Captain
 
skins333's Avatar
 
Drives: '08 E93 BMW M3 MR/'12 x5d SG
Join Date: May 2009
Location: Northern VA

Posts: 983
iTrader: (2)

you guys are the best...took less than 10 min total, no scratches. ( i did spend some good time doing research though)
skins333 is offline   United_States
0
Reply With Quote
      01-26-2012, 08:40 PM   #22
pak10
New Member
 
Drives: E92
Join Date: Dec 2011
Location: Underground

Posts: 17
iTrader: (0)

BimmerM

Thanks for the excellent write up. I swapped mine out today and it looks so much cleaner.
pak10 is offline  
0
Reply With Quote
Post Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 10:03 PM.




m3post
Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST